Bedienungsanleitung TECHNIRADIO 4 IR DAB+/UKW/Internet-Radio
1 Abbildungen 1.
1.
1.
1 2 3 4 5 6 7 8 9 10-13 14 15 16 NAVIGATE/SELECT Drehregler (Drehen = Auswahl, Drücken = Übernehmen) Ein/Standby/Volume (Drehen = Lautstärke, Drücken = Ein-Ausschalten) Farb-Display MODE (Quellen-Umschaltung) MENU (Aufrufen des Hauptmenü) INFO (Displayanzeigen durchschalten) Vorheriger Titel (FM Sendersuche) Nächster Titel (FM Sendersuche) PRESET (Favoritenspeicher) Direktwahltasten 1...4 (Favoritenspeicher 1...
2 Inhaltsverzeichnis 1 1.1 1.2 1.3 Abbildungen................................................................................................................ 2 Ansicht von vorne........................................................................................................................ 2 Tastenfeld.........................................................................................................................................3 Ansicht von hinten...........................................
6.2 6.3 6.3.1 6.3.2 6.3.3 6.4 6.4.1 6.4.2 6.4.3 6.4.4 6.4.5 Die besonderen Eigenschaften des TECHNIRADIO 4 IR.......................................... 21 TECHNIRADIO 4 IR zum Betrieb vorbereiten................................................................22 Teleskopantenne ausrichten.................................................................................................22 Netzteil anschließen.......................................................................................................
9.2.4 9.2.5 9.2.6 9.2.7 9.2.8 9.2.9 9.2.10 DAB+ -Sender auf einem Speicherplatz ablegen....................................................... 37 DAB+ -Sender von einem Speicherplatz abrufen......................................................38 Überschreiben/Löschen einer Programmplatz-Speicherung...............................38 Signalstärke...................................................................................................................................38 Lautstärkeanpassung (DRC)......
11.3 11.4 11.5 Favoriten speichern................................................................................................................. 49 Favoriten abrufen..................................................................................................................... 50 Überschreiben/Löschen einer Programmplatz-Speicherung.............................. 50 12 12.1 12.2 12.2.1 12.2.2 12.3 12.3.1 Weitere Funktionen............................................................................
13.3 13.4 13.5 13.6 13.7 13.8 13.9 Display Einstellungen...............................................................................................................65 Sprache.......................................................................................................................................... 66 Werkseinstellung....................................................................................................................... 66 Systeminfo...........................................
3 Sicherheitshinweise 3.1 Verwendete Zeichen und Symbole In dieser Bedienungsanleitung: Kennzeichnet einen Sicherheitshinweis, der bei Nichtbeachtung zu schweren Verletzungen oder zum Tod führen kann.
Auf dem Gerät: Benutzung in Innenräumen - Geräte mit diesem Symbol sind nur für die Verwendung in Innenräumen geeignet. Schutzklasse II - Elektrogeräte der Schutzklasse II sind Elektrogeräte die durchgehende doppelte und/oder verstärkte Isolierung besitzen und keine Anschlussmöglichkeiten für einen Schutzleiter haben. Das Gehäuse eines isolierstoffumschlossenen Elektrogerätes der Schutzklasse II kann teilweise oder vollständig die zusätzliche oder verstärkte Isolierung bilden.
3.2 Bestimmungsgemäßer Gebrauch Das Gerät ist für den Empfang von Radiosendungen über DAB+, FM und Internet entwickelt. Das Gerät ist für den privaten Gebrauch konzipiert und nicht für gewerbliche Zwecke geeignet. 3.3 Die Zielgruppe dieser Bedienungsanleitung Die Bedienungsanleitung richtet sich an jede Person, die das Gerät aufstellt, bedient, reinigt oder entsorgt. 3.
Nutzung des Gerätes und um Gerätedefekten und Personenschäden vorzubeugen. - Reparieren Sie das Gerät nicht selbst. Eine Reparatur darf nur von geschultem Fachpersonal durchgeführt werden. Wenden Sie sich an unsere Kundendienststellen. - Das Gerät darf nur in den dafür angegebenen Umgebungsbedingungen betrieben werden. - Setzen Sie das Gerät nicht Tropf- oder Spritzwasser aus.
- Wenn das Gerät Schäden aufweist, darf es nicht in Betrieb genommen werden. - Nehmen Sie das Gerät nicht in der Nähe von Badewannen, Duschen, Swimmingpools oder fließendem/spritzendem Wasser in Betrieb. Es besteht die Gefahr eines elektrischen Schlages und/oder Gerätedefekten. - Fremdkörper, z.B. Nadeln, Münzen, etc., dürfen nicht in das Innere des Gerätes fallen. Die Anschlusskontakte nicht mit metallischen Gegenständen oder den Fingern berühren. Die Folge können Kurzschlüsse sein.
4 Rechtliche Hinweise Hiermit erklärt TechniSat, dass der Funkanlagentyp TECHNIRADIO 4 IR der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EUKonformitätserklärung ist unter der folgenden Internetadresse verfügbar: http://konf.tsat.de/?ID=22305 TechniSat ist nicht für Produktschäden auf Grund von äußeren Einflüssen, Verschleiß oder unsachgemäßer Handhabung, unbefugter Instandsetzung, Modifikationen oder Unfällen haftbar. Änderungen und Druckfehler vorbehalten. Stand 11/20.
TECHNIRADIO 4 IR und TechniSat sind eingetragene Warenzeichen der: TechniSat Digital GmbH TechniPark Julius-Saxler-Straße 3 D-54550 Daun/Eifel www.technisat.de Namen der erwähnten Firmen, Institutionen oder Marken sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber. In den nachfolgend aufgeführten Ländern darf das Gerät im 5GHz WLANBereich nur in geschlossenen Räumen betrieben werden.
4.1 Servicehinweise Dieses Produkt ist qualitätsgeprüft und mit der gesetzlichen Gewährleistungszeit von 24 Monaten ab Kaufdatum versehen. Bitte bewahren Sie den Rechnungsbeleg als Kaufnachweis auf. Bei Gewährleistungsansprüchen wenden Sie sich bitte an den Händler des Produktes. Hinweis! Für Fragen und Informationen oder wenn es mit diesem Gerät zu einem Problem kommt, ist unsere Technische Hotline: Mo. - Fr. 8:00 - 18:00 unter Tel.: 03925/9220 1800 erreichbar.
Für eine eventuell erforderliche Einsendung des Gerätes verwenden Sie bitte ausschließlich folgende Anschrift: TechniSat Digital GmbH Service-Center Nordstr. 4a 39418 Staßfurt 5 Aufstellen des Gerätes > Stellen Sie das Gerät auf einen festen, sicheren und horizontalen Untergrund. Sorgen Sie für gute Belüftung. Hinweis: - Stellen Sie das Gerät nicht auf weiche Oberflächen wie Teppiche, Decken oder in der Nähe von Gardinen und Wandbehängen auf.
- Der Standort darf nicht in Räumen mit hoher Luftfeuchtigkeit, z. B. Küche oder Sauna, gewählt werden, da Niederschläge von Kondenswasser zur Beschädigung des Gerätes führen können. Das Gerät ist für die Verwendung in trockener Umgebung und in gemäßigtem Klima vorgesehen und darf nicht Tropf- oder Spritzwasser ausgesetzt werden. - Beachten Sie, dass die Gerätefüße u. U. farbige Abdrücke auf bestimmten Möbeloberflächen hinterlassen könnten. Verwenden Sie einen Schutz zwischen Ihren Möbeln und dem Gerät.
- Bei Störungen oder Rauch- und Geruchsbildung aus dem Gehäuse sofort Netzstecker aus der Steckdose ziehen! - Wenn das Gerät längere Zeit nicht benutzt wird, z. B. vor Antritt einer längeren Reise, ziehen Sie den Netzstecker. 6 Beschreibung des TECHNIRADIO 4 IR 6.1 Der Lieferumfang Bitte überprüfen sie vor Inbetriebnahme, ob der Lieferumfang vollständig ist: 1x TECHNIRADIO 4 IR 1x Netzteil 1x Bedienungsanleitung 6.
- Internetradiobetrieb über WLAN Farb-Display. 6.3 TECHNIRADIO 4 IR zum Betrieb vorbereiten 6.3.1 Teleskopantenne ausrichten Die Anzahl und Qualität der zu empfangenden Sender hängt von den Empfangsverhältnissen am Aufstellort ab. Mit der Teleskopantenne kann ein ausgezeichneter Empfang erzielt werden. > Lösen Sie die Teleskopantenne aus der Halterung, richten Sie sie auf und ziehen Sie sie der Länge nach aus.
kann zu Empfangsbeeinträchtigungen und Tonaussetzern führen. 6.3.2 Netzteil anschließen Vergewissern Sie sich, dass die Betriebsspannung des Netzteils mit der örtlichen Netzspannung übereinstimmt, bevor Sie es in die Wandsteckdose stecken. WARNUNG! Netzstecker nicht mit nassen Händen anfassen, Gefahr eines elektrischen Schlages! ACHTUNG! Verlegen Sie das Netzkabel so, dass niemand darüber stolpern kann.
6.3.3 Kopfhörer benutzen ACHTUNG! Gehörschäden! Hören Sie Radio nicht mit großer Lautstärke über Kopfhörer. Dies kann zu bleibenden Gehörschäden führen. Regeln Sie vor der Verwendung von Kopfhörern die Gerätelautstärke auf minimale Lautstärke. Verwenden Sie nur Kopfhörer mit 3,5 mm Stereo-Klinkenstecker. > Stecken Sie den Stecker des Kopfhörers in die Kopfhörerbuchse (16) auf der Rückseite des Gerätes.
6.4 Allgemeine Geräte-Funktionen 6.4.1 Gerät einschalten > Bereiten Sie das TECHNIRADIO 4 IR zunächst wie unter Punkt 6.3.1 und 6.3.2 beschrieben, zum Betrieb vor. > Durch Drücken des VOLUME/ TECHNIRADIO 4 IR ein. Drehreglers (2), schalten Sie das Nach dem erstmaligen Einschalten müssen Sie zuerst den Erstinstallationsassistenten Konfigurieren. Näheres im Kapitel 8. 6.4.2 Gerät ausschalten > Durch Drücken des VOLUME/ Drehreglers können Sie das Gerät in den Standby-Modus schalten.
6.4.3 Quellenwahl > Mit der Taste MODE (4) kann zwischen den Quellen Internetradio, DAB+ (Digital Radio), FM (UKW) umgeschaltet werden. Die Quellen werden anhand eines Symbols dargestellt. DAB+ FM (UKW) Internetradio 6.4.4 Lautstärke einstellen > Stellen Sie die Lautstärke durch Drehen des VOLUME/ Drehreglers (2) ein. Die eingestellte Lautstärke wird im Display anhand eines Balkendiagrammes gezeigt.
6.4.
6.4.5.1 Displayanzeigen aufrufen > Drücken Sie mehrmals die Taste INFO (6). Sie haben die Wahl, sich folgende Infos anzeigen zu lassen: Im Internetradio -Betrieb (gewählte Funktion wird mit einem “*” gekennzeichnet): [Beschreibung], [Genre], [Zuverlässigkeit], [Bit-Rate], [Tonformat], [Abspiel-Puffer], und [Datum]. Im DAB+ -Betrieb (gewählte Funktion wird mit einem “*” gekennzeichnet): [Lauftext] (durchlaufender Text mit zusätzlichen Informationen, die die Sender u. U.
6.4.5.2 Slideshow Einige DAB+ Sender übertragen Zusätzliche Informationen wie z. B. Albumcover des Aktuellen Titels, Werbung oder Wetterdaten. Die Größe des Fensters kann durch gedrückt Halten des NAVIGATE/SELECT Drehreglers geändert werden. 7 Menübedienung Über das Menü gelangen Sie zu allen Funktionen und Einstellungen des TECHNIRADIO 4 IR. Die Menü-Navigation erfolgt mit den Tasten MENU und dem NAVIGATE/SELECT Drehregler.
nicht übernommen und gespeichert und Sie gelangen einen Schritt zurück. Funktionen und zu drückende Tasten werden in dieser Bedienungsanleitung in fett dargestellt. Displayanzeigen in [eckigen Klammern]. Einige Textdarstellungen (z. B. Menüeinträge, Senderinformationen) sind eventuell für die Anzeige im Display zu lang. Diese werden dann nach kurzer Zeit als Lauftext dargestellt.
8 Ersteinrichtung Nach dem erstmaligen Einschalten des TECHNIRADIO 4 IR startet der Ersteinrichtungsassistent. Alle Einstellungen können auch zu einem späteren Zeitpunkt jederzeit geändert werden. > Wählen Sie zuerst mit dem NAVIGATE/SELECT Drehregler die Menüsprache. Drücken Sie den NAVIGATE/SELECT Drehregler, um die Sprache zu übernehmen und zur nächsten Einstellung zu gelangen. > Beachten Sie die Hinweise zum Datenschutz und drücken Sie den NAVIGATE/ SELECT Drehregler.
Haben Sie Aktualisierung von NET gewählt, müssen Sie im nächsten Schritt noch die Zeitzone wählen, damit die Uhrzeit korrekt dargestellt wird. Legen Sie anschließend fest, ob zum Zeitpunkt der Einstellung die Sommerzeit oder die Winterzeit aktuell ist. > Im nächsten Schritt können Sie festlegen, ob das TECHNIRADIO 4 IR auch im Standby mit dem Internet verbunden bleiben soll. Jedoch erhöht sich dadurch der Stromverbrauch im Standby-Modus.
Während die virtuelle Tastatur im Display dargestellt wird, können Sie durch Drehen des NAVIGATE/SELECT Drehreglers navigieren. > Bestätigen Sie nach Abschluss der Netzwerkkonfiguration den Hinweis, das die Ersteinrichtung abgeschlossen ist, durch Drücken des NAVIGATE/SELECT Drehreglers. 9 Die DAB+ (Digital Radio)-Funktion 9.1 Was ist DAB+ und DAB+ Cable DAB+ ist ein neues digitales Format, durch welches Sie kristallklaren Sound ohne Rauschen hören können.
9.2 DAB+ (Digital Radio) Empfang > Drücken Sie die Taste MODE bis [DAB Radio] im Display angezeigt wird. Wird DAB+ zum ersten Mal gestartet, wird ein kompletter Sendersuchlauf durchgeführt. Nach Beendigung des Suchlaufes kann ein Sender aus der Senderliste gewählt und durch Drücken des NAVIGATE/SELECT Drehregler wiedergegeben werden. 9.2.
> Drücken Sie den NAVIGATE/SELECT Drehregler. > Im Display erscheint [Suchlauf...]. Während des Suchlaufs wird ein Fortschrittsbalken und die Anzahl an gefundenen Sendern angezeigt. Wird keine Station gefunden, prüfen Sie die Wurfantenne und verändern Sie ggf. den Aufstellort (Punkt 6.3.1). 9.2.2 Manuell einstellen Dieser Menüpunkt dient der Überprüfung der Empfangskanäle und kann zur Ausrichtung der Antenne dienen. Des Weiteren können Sender manuell hinzugefügt werden.
Signalstärke angezeigt. Wird auf einem Kanal ein DAB+ -Sender empfangen, wird der Ensemblename des Senders angezeigt. Die Antenne kann nun auf maximale Signalstärke ausgerichtet werden. Sender, deren Signalstärke unterhalb der erforderlichen Mindestsignalstärke liegt, senden kein ausreichendes Signal. Richten Sie die Teleskopantenne ggf. wie unter Punkt 6.3.1 beschrieben aus.
> Drücken Sie den NAVIGATE/SELECT Drehregler. 9.2.4 DAB+ -Sender auf einem Speicherplatz ablegen Der Programm-Speicher kann bis zu 40 Stationen im DAB+ -Bereich speichern. > Wählen Sie zunächst den gewünschten Sender aus (siehe Punkt 9.2.3). > Um diesen Sender auf einem Speicherplatz abzulegen, halten Sie während der Wiedergabe die Taste PRESET (9) gedrückt, bis [Sender speichern] im Display erscheint. Wählen Sie anschließend mit dem NAVIGATE/SELECT Drehregler einen Favoritenspeicher (1...40).
9.2.5 DAB+ -Sender von einem Speicherplatz abrufen > Um einen Sender abzurufen, den Sie zuvor im FAV-Speicher abgelegt haben, drücken Sie kurz die Taste PRESET und wählen Sie mit dem NAVIGATE/ SELECT Drehregler einen Senderspeicher (1...40). Drücken Sie den NAVIGATE/ SELECT Drehregler zur Wiedergabe des Senders. Ist kein Sender auf dem gewählten Programmplatz gespeichert, erscheint im Display [(leer)]. Alternativ kann auch die entsprechende Direktwahltaste 1...4 gedrückt werden. 9.2.
> Im Display wird die Signalstärke anhand eines Balkendiagrammes dargestellt. Die Markierung zeigt die Mindestsignalstärke. Sender, deren Signalstärke unterhalb der erforderlichen Mindestsignalstärke liegt, senden kein ausreichendes Signal. Richten Sie die Teleskopantenne ggf. wie unter Punkt 6.3.1 beschrieben aus. 9.2.
> Öffnen Sie das Hauptmenü durch Drücken der Taste MENU und wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Lautstärkeanpassung]. > Drücken Sie den NAVIGATE/SELECT Drehregler. > Wählen Sie mit dem NAVIGATE/SELECT Drehregler eine der Optionen: DRC hoch DRC tief DRC aus - > Hohe Kompression Niedrige Kompression Kompression abgeschaltet. Bestätigen Sie die Einstellung durch Drücken des NAVIGATE/SELECT Drehreglers. 9.2.
bestätigen Sie durch Drücken des NAVIGATE/SELECT Drehreglers. 9.2.10 Senderreihenfolge Die Anzeige der Sender in der Senderliste kann entweder Alphanumerisch oder nach Anbietern sortiert werden. > Öffnen Sie das Hauptmenü durch Drücken der Taste MENU und wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Senderreihenfolge]. > Drücken Sie den NAVIGATE/SELECT Drehregler.
10 FM (UKW)-Betrieb 10.1 UKW-Radiobetrieb einschalten > Drücken Sie die Taste MODE bis [FM Radio] im Display angezeigt wird. Beim erstmaligen Einschalten ist die Frequenz 87,50 MHz eingestellt. Haben Sie bereits einen Sender eingestellt oder gespeichert, spielt das Radio den zuletzt eingestellten Sender. Bei RDS-Sendern erscheint der Sendername. Um den Empfang zu verbessern, richten Sie die Antenne aus (Punkt 6.3.1). 10.
10.3 Automatische Sendersuche > Halten Sie die Taste Vorheriger Titel (7) oder Nächster Titel (8) gedrückt, um automatisch den nächsten Sender mit ausreichendem Signal zu suchen. Wird ein UKW-Sender mit ausreichend starkem Signal gefunden, stoppt der Suchlauf und der Sender wird wiedergegeben. Wird ein RDS-Sender empfangen erscheint der Sendername und ggf. der Radiotext. Für die Einstellung schwächerer Sender benutzen Sie bitte die manuelle Sendersuche. 10.
10.5 Suchlauf-Einstellung In diesem Menüpunkt kann die Empfindlichkeit des Suchlaufs eingestellt werden. > Öffnen Sie das Hauptmenü durch Drücken der Taste MENU und wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Suchlauf-Einstellungen]. > Drücken Sie den NAVIGATE/SELECT Drehregler. > Wählen Sie aus, ob der Suchlauf nur bei starken Sendern [JA] stoppen soll oder bei allen Sendern (auch bei schwachen Sendern) [NEIN].
> Wählen Sie mit dem NAVIGATE/SELECT Drehregler den Eintrag [JA] (nur Mono) oder [NEIN] (Stereo-Empfang), um den Empfang in Stereo oder nur in Mono-Ton bei schwachem FM-Empfang wiederzugeben. > Bestätigen Sie die Einstellung durch Drücken des NAVIGATE/SELECT Drehregler. Wiedergabe des Stereo-Tons nur über Kopfhörer möglich. 10.7 UKW-Sender auf einem Speicherplatz ablegen Der Programm-Speicher kann bis zu 40 Stationen im FM/UKW-Bereich speichern.
Sie können Sender auch direkt auf eine der Direktwahltasten 1...4 speichern, indem Sie die entsprechende Taste länger gedrückt halten. 10.8 UKW-Sender von einem Speicherplatz abrufen > Um einen Sender abzurufen, den Sie zuvor im FAV-Speicher abgelegt haben, drücken Sie kurz die Taste PRESET und wählen Sie mit dem NAVIGATE/ SELECT Drehregler einen Senderspeicher (1...40). Drücken Sie den NAVIGATE/ SELECT Drehregler zur Wiedergabe des Senders.
11 Internetradio Das TECHNIRADIO 4 IR ist mit einem Internet-Radio Empfänger ausgestattet. Um Internet-Radio Stationen/Sender empfangen zu können, benötigen Sie eine Internetverbindung über einen WLAN-Router zu einem Drahtlosnetzwerk. > Drücken Sie die Taste MODE bis [Internet Radio] im Display angezeigt wird.
Ob eine Verbindung besteht, erkennen Sie an den Signalbalken in der Statusleiste des Displays. Um die Eingabe abzubrechen, wählen Sie und drücken Sie den NAVIGATE/SELECT Drehregler. Haben Sie sich vertippt, können sie den zuletzt eingegebenen Buchstaben mit löschen. Während die virtuelle Tastatur im Display dargestellt wird, können Sie durch Drehen des NAVIGATE/SELECT Drehreglers navigieren. 11.
11.2 Verlauf > Wählen Sie MENU > Senderliste > Verlauf, um eine Liste mit den zuletzt wiedergegebenen Sendern anzuzeigen. > Wählen Sie mit dem NAVIGATE/SELECT Drehregler einen Sender und geben Sie ihn durch Drücken des NAVIGATE/SELECT Drehregler wieder. 11.3 Favoriten speichern Der Programm-Speicher kann bis zu 40 Stationen im Internetradio-Bereich speichern. > Suchen Sie zuerst einen Sender aus der Senderliste aus und geben Sie ihn wieder.
Sie können Sender auch direkt auf eine der Direktwahltasten 1...4 speichern, indem Sie die entsprechende Taste länger gedrückt halten. 11.4 Favoriten abrufen > Um einen Sender abzurufen, den Sie zuvor im FAV-Speicher abgelegt haben, drücken Sie kurz die Taste PRESET und wählen Sie mit dem NAVIGATE/ SELECT Drehregler einen Senderspeicher (1...40). Drücken Sie den NAVIGATE/ SELECT Drehregler zur Wiedergabe des Senders.
12 Weitere Funktionen 12.1 Sleep-Timer Durch den Sleep-Timer schaltet das TECHNIRADIO 4 IR nach der eingestellten Zeit automatisch in den Standby. > Öffnen Sie das Hauptmenü durch Drücken der Taste MENU und wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Systemeinstellungen] > [Sleep]. > Drücken Sie den NAVIGATE/SELECT Drehregler. > Wählen Sie mit dem NAVIGATE/SELECT Drehregler einen Zeitraum, nach dem das TECHNIRADIO 4 IR ausschalten soll.
12.2 Wecker Der Wecker schaltet das TECHNIRADIO 4 IR zur eingestellten Weckzeit ein. Es können 2 Weckzeiten programmiert werden. Als Beispiel erfolgt die Beschreibung der Programmierung von Wecker 1. 12.2.1 Wecker einrichten > Öffnen Sie das Hauptmenü durch Drücken der Taste MENU und wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Systemeinstellungen] > [Wecker]. > Drücken Sie den NAVIGATE/SELECT Drehregler.
Wiederholung > Sie können hier zwischen Aus, Täglich (jeden Tag in der Woche), Einmal, Werktage (Mo. - Fr.) oder Wochenende (Sa. u. So.) wählen. Drücken Sie zum Übernehmen der Einstellung den NAVIGATE/SELECT Drehregler. Uhrzeit und Datum > Hier können Sie die Weckzeit und ggf. das Datum eingeben. Wählen Sie zuerst mit dem NAVIGATE/SELECT Drehregler die Stunden und drücken Sie zum Übernehmen den NAVIGATE/SELECT Drehregler. Es folgt die Eingabe der Minuten.
Haben Sie Internet Radio, DAB oder FM gewählt, können Sie anschließend angeben, ob Sie mit dem zuletzt gehörten Sender geweckt werden wollen, oder mit einem aus Ihrer Favoritenliste. Lautstärke > Zuletzt können Sie die Weckton-Lautstärke festlegen. Drücken Sie zum Übernehmen den NAVIGATE/SELECT Drehregler. Speichern > Drücken Sie den NAVIGATE/SELECT Drehregler, um den Wecker zu speichern. Damit der Wecker ordnungsgemäß funktioniert, muss die Uhrzeit eingelesen werden. Näheres hierzu unter Punkt 13.2.2.
Möchten Sie die Schlummer-Funktion aktivieren, drücken Sie mehrmals bei aktivem Wecker den NAVIGATE/SELECT Drehregler. Jeder Druck erhöht die Schlummer-Zeit. 12.3 Equalizer Mit dem Equalizer können Sie den Ton Ihren Wünschen entsprechend anpassen. > Öffnen Sie das Hauptmenü durch Drücken der Taste MENU und wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Systemeinstellungen] > [Equalizer]. > Drücken Sie den NAVIGATE/SELECT Drehregler.
12.3.1 Mein EQ anpassen Die Equalizer-Voreinstellung MeinEQ kann angepasst werden. > Öffnen Sie das Hauptmenü durch Drücken der Taste MENU und wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Systemeinstellungen] > [Equalizer] > [Meine EQ-Einstellung]. > Drücken Sie den NAVIGATE/SELECT Drehregler. > Wählen Sie mit dem NAVIGATE/SELECT Drehregler entweder [Höhen], um die Höhen anzupassen oder [Bass], um die Tiefen anzupassen. Drücken Sie anschließend den NAVIGATE/SELECT Drehregler.
13 Systemeinstellungen Alle unter diesem Punkt erläuterten Einstellungen gelten für alle Quellen gleichermaßen. > Öffnen Sie das Hauptmenü durch Drücken der Taste MENU und wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Systemeinstellungen]. > Drücken Sie den NAVIGATE/SELECT Drehregler. 13.1 Interneteinstellungen > Über Menü > [Systemeinstellungen] > [Interneteinstellung] können Sie die Netzwerkeinstellungen aufrufen und konfigurieren. 13.1.
> Wählen Sie anschließend Ihr WLAN-Netz aus. Nun können Sie wählen, ob Sie die WPS-Funktion nutzen oder Ihr WLANPasswort manuell eingeben möchten. > Wenn Sie die WPS-Funktion nutzen möchten, starten Sie diese zunächst an Ihrem Router gemäß dessen Bedienungsanleitung und wählen Sie anschließend im Netzwerkassistenten [WPS Taste drücken] aus. Bitte beachten Sie die Displayeinblendungen.
13.1.1.2 Konfiguration per WPS-Funktion Hierdurch wird eine direkte Verbindung zum Router hergestellt. Eine Auswahl und/ oder Eingabe von WLAN-Netz (SSID) und Passwort ist nicht nötig. > Starten Sie die WPS-Funktion an Ihrem Router gemäß dessen Bedienungsanleitung. > Wählen Sie anschließend [WPS Taste drücken], um den Verbindungsvorgang zu starten. Bitte beachten Sie die Displayeinblendungen.
Bitte beachten Sie, dass das automatische Abrufen der IP-Adresse, Gateway, Subnetzmaske nur funktioniert, wenn die DHCP-Funktion in Ihrem Router aktiviert ist. > Geben Sie nacheinander die IP-Adresse, Subnetzmaske, Gateway-Adresse, Primärer DNS und ggf. Sekundärer DNS mit Hilfe des NAVIGATE/SELECT Drehregler ein. Bestätigen Sie jeden eingestellten Wert durch Drücken des NAVIGATE/SELECT Drehregler.
13.1.2 Einstellungen anzeigen > Wählen Sie [Einstellungen anzeigen] aus, um sich die aktuellen Netzwerkeinstellungen anzeigen zu lassen. 13.1.3 Netzwerkprofil löschen Verwenden Sie die Menüpunkte [Inaktive Netzwerke löschen ] oder [Alle Netzwerkverbindungen löschen] um eine bestehende Verbindung zu einem WLANNetzwerk oder allen konfigurierten Netzwerken zu löschen und die vorgenommenen Einstellungen zu löschen.
13.2 Uhrzeit- und Datumseinstellungen 13.2.1 Zeit/Datum manuell einstellen Je nach Einstellung der Zeitaktualisierung (Punkt 13.2.2), müssen Sie Uhrzeit und das Datum manuell einstellen. > Öffnen Sie das Menü > [Systemeinstellungen] > [Zeit und Datum]. > Drücken Sie den NAVIGATE/SELECT Drehregler. > Wählen Sie mit dem NAVIGATE/SELECT Drehregler > [Zeit/ Datumseinstellung] und drücken Sie den NAVIGATE/SELECT Drehregler.
> Verfahren Sie bei der Uhrzeit wie zuvor beschrieben. > Nachdem alle Einstellungen vorgenommen wurden und letztmalig der NAVIGATE/SELECT Drehregler gedrückt wurde, erscheint [Uhrzeit Gespeichert] im Display. 13.2.2 Zeitaktualisierung Hier können Sie festlegen, ob die Synchronisierung automatisch über DAB+, Internet oder FM (UKW) erfolgen soll oder ob Sie sie manuell eingeben möchten (Punkt 13.2.1).
> Drücken Sie zum Speichern der Einstellung den NAVIGATE/SELECT Drehregler drücken. Haben Sie [Aktualisieren von Net] gewählt, müssen Sie auch die Zeitzone und die Sommer/Winterzeiteinstellung konfigurieren. Dies geschieht unter [Systemeinstellungen] > [Zeit und Datum] > [Zeitzone einstellen] und [Systemeinstellungen] > [Zeit und Datum] > [Sommerzeit?]. 13.2.3 Uhrzeitformat einstellen Unter Zeitformat können Sie das 12 oder 24 Stunden Format aktivieren.
13.3 Display Einstellungen Sie können die Displayhelligkeit sowohl für den Betrieb als auch für Standby einstellen. > Öffnen Sie das Menü > [Systemeinstellungen] > [Beleuchtung] und Drücken Sie den NAVIGATE/SELECT Drehregler. > Wählen Sie mit dem NAVIGATE/SELECT Drehregler eine Option: [Betrieb] regelt die Helligkeit im normalen, eingeschalteten Zustand. Sie können hier zwischen den Helligkeitsstufen [Hoch], [Mittel] und [Niedrig] wählen.
Wird die Option [Aus] gewählt, leuchtet das Display mit der unter der Funktion [Betrieb] gewählten Helligkeit dauerhaft. Drücken Sie zum Speichern einer Einstellung den NAVIGATE/SELECT Drehregler. 13.4 Sprache > Öffnen Sie das Menü > [Systemeinstellungen] > [Sprache] und Drücken Sie den NAVIGATE/SELECT Drehregler. > Wählen Sie mit dem NAVIGATE/SELECT Drehregler eine der zur Verfügung stehenden Sprachen und bestätigen Sie die Auswahl durch Drücken des NAVIGATE/SELECT Drehregler. 13.
Werkseinstellung den Eintrag [Ja] und drücken Sie den NAVIGATE/SELECT Drehregler. Alle zuvor gespeicherten Sender und Einstellungen werden gelöscht. Das Gerät befindet sich nun im Auslieferungszustand. > Im Display erscheint [Neustart...] und das Gerät startet mit dem Ersteinrichtungsassistenten. Beachten Sie die Hinweise unter Punkt „8 Ersteinrichtung“ auf Seite 31. 13.6 Systeminfo Unter Info können Sie die aktuell installierte Software-Version abfragen.
Auto-Update > Schalten Sie die Automatische Suche nach neuen Software Versionen an (JA) oder aus (NEIN). Jetzt prüfen > Startet sofort die Suche nach einer neuen Software-Version. Wurde eine neue Software Version gefunden, können Sie diese direkt aktualisieren. Beachten Sie hierbei die Hinweise auf dem Display. Trennen Sie während dem Update-Prozess zu keiner Zeit die Stromversorgung. Ansonsten kann das Gerät beschädigt werden.
13.8 Ersteinrichtung Hier kann der Ersteinrichtungsassistent erneut aufgerufen werden. Näheres hierzu unter Punkt „8 Ersteinrichtung“ auf Seite 31. > Öffnen Sie das Menü > [Systemeinstellungen] > [Einrichtungsassistent] und Drücken Sie den NAVIGATE/SELECT Drehregler. 13.9 Datenschutz Unter diesem Punkt finden Sie Datenschutzinformationen. > Öffnen Sie das Menü > [Systemeinstellungen] > [Datenschutz] und Drücken Sie den NAVIGATE/SELECT Drehregler.
14 Reinigen Um die Gefahr eines elektrischen Schlags zu vermeiden, dürfen Sie das Gerät nicht mit einem nassen Tuch oder unter fließendem Wasser reinigen. Vor der Reinigung den Netzstecker ziehen und Gerät ausschalten! Sie dürfen keine Scheuerschwämme, Scheuerpulver und Lösungsmittel wie Alkohol oder Benzin verwenden. Keine der folgenden Substanzen verwenden: Salzwasser, Insektenvernichtungsmittel, chlor- oder säurehaltige Lösungsmittel (Salmiak).
15 Fehler beseitigen Wenn das Gerät nicht wie vorgesehen funktioniert, überprüfen Sie es anhand der folgenden Tabelle. Symptom Mögliche Ursache/Abhilfe Gerät lässt sich nicht einschalten. Das Gerät wird nicht mit Strom versorgt. Schließen Sie das Netzteil richtig an die Steckdose und am Gerät an. Es ist kein Ton zu hören. Erhöhen Sie die Lautstärke. Das Display schaltet sich nicht ein. Gerät vom Stromnetz trennen und Gerät wieder mit Strom versorgen. Empfang über DAB+/FM ist schlecht.
Symptom Gerät schaltet selbstständig in Standby Mögliche Ursache/Abhilfe Die Auto-Standby-Funktion schaltet das Gerät selbstständig nach ca. 15 Minuten in Standby, wenn z. B. keine Musik wiedergegeben wird. Wenn Sie die Störung auch nach den beschriebenen Überprüfungen nicht beheben können, nehmen Sie bitte Kontakt mit der technischen Hotline auf.
16 Technische Daten / Herstellerhinweise Technische Änderungen und Irrtümer vorbehalten. Empfangswege DAB/DAB+, FM, Internet Stromversorgung DC 5 V, 2 A über externes mitgeliefertes Netzteil Frequenzen UKW: 87,5-108 MHz DAB/DAB+: 174-240 MHz WLAN: 2400 MHz - 2483 MHz Sendeleistung: max. +17 dBm EIRP 5150 MHz - 5875MHz Sendeleistung: max. +17 dBm EIRP WLAN IEEE 802.11 a/b/g/n Dual band 2.
Leistungsaufnahme im Betrieb typisch: 7,2 W Standby: 0,95 W mit aktiver Netzwerkverbindung: 1,35 W Umgebungsbedingungen Betrieb 5 - 35° C 5 - 90% Luftfeuchtigkeit Gewicht (g) 675 Abmessungen (BxHxT) mm 210 x 143 x 81 74
Technische Daten des mitgelieferten Netzteils Hersteller TechniSat Digital GmbH, Julius-SaxlerStraße 3, D-54550 Daun Modellkennung OBL-0502000E Eingangsspannung AC 100 - 240 V Eingangswechselstromfrequenz 50/60 Hz Ausgangsspannung DC 5,0 V Ausgangsstrom 2,0 A Ausgangsleistung 10,0 W Durchschnittliche Effizienz im Betrieb 82,1 % Leistungsaufnahme bei Nulllast 0,07 W 75
04112020ORV2 76