User's Manual

TECHNICAL SPECIFICATIONS
WARRANTY INFORMATION
We do our best to make sure that this product is free from defects in
materials and workmanship for a period of 1 year.
The following conditions must be met for your warranty claim to be
approved:
You must have purchased the product from a Nautica or Technofashion
authorized dealer.
You must provide proof as to the date of purchase from the Nautica or
Technofashion authorized dealer.
You must have used the product only as intended and in accordance with
the product’s care instructions.
Within 12 months after the purchase, in case the product is determined
to be defective (at the date of original purchase) due to improper
materials or workmanship, you are entitled to free repair or exchange of
goods. The product should be returned to Technofashion.
For any questions, email us at
[e-mail]
FCC ID: 2AZBO-N00012
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This device generates, uses, and can radiate radio frequency energy and, if
For the smart phone models without magnetic
feature, metal plate (included) can be installed on
the outside of your smart device case, inside the
case or directly on the smart device.
1. Use the alcohol wipe to clean the surface on the
back of the device or case and allow to fully dry.
2. Remove the adhesive covering from the metal
plate.
3. Place the disk on to the cleaned area of the
device or case.
4. Remove transparent film from the front surface
of magnetic wireless car charger.
Thank you for purchasing an original
Nautica Magnetic Wireless Car Charger
You are getting a high-quality product that’s built to combine
technology and design for your everyday use.
Please read the below info carefully to get the most out of your new
product.
This guide is ENGLISH only. For other languages and
more detailed info on care, use and warranty,
please visit technofashion.com
© 2021 Technofashion, Inc. All Rights Reserved.
Designed in USA. Made in China.
May be patented. See technofashion.com/patents
designed, manufactured, distributed by
HOW TO USE
SUPPORT
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be
determined by turning the device off and on, the user is encoura ged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Changes
or modifications not expressively approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The distance between user and products should be no less than
7.87 in / 20 cm
WHAT’S IN THE BOX ?
SAFETY AND MAINTENANCE
Before using your Nautica Magnetic Wireless Car Charger, read the
following precautions carefully to ensure optimal product performance.
Do not expose your wireless car charger and its electronic parts to
extremely hot (fire, direct sunlight, etc.) or cold conditions.
Extreme temperatures may cause the unit to explode or overheat which
may in turn result in lower performance and a shorter life span. Also avoid
applying high pressure or penetration to the unit with sharp objects.
Keep your credit cards or any other cards with magnetic chips or strips on
them away from your Nautica Magnetic Wireless Car Charger against the
possibility of demagnetization.
MAGNETIC WIRELESS
CAR CHARGER
NTMC02
The warranty does not cover defects caused by third-party modifications,
repairs or replacement parts.
Punctures, scratches, normal wear and tear and the natural breakdown of
colors and materials over extended time and use are not warranted.
Warranty applies to the USA only.
We will make every effort to replace limited edition or discontinued
products but cannot guarantee availability for replacement.
Any limited edition or discontinued product still under its applicable
warranty that cannot be replaced with an identical product will be
replaced with the equivalent model based on availability.
We may make changes to products and designs in the time you
purchased your product and submitted a warranty claim.
Products repaired or replaced under this warranty may or may not
incorporate these changes.
Do not attempt to modify, repair, or replace any components of your
Nautica Magnetic Wireless Car Charger. Only authorized dealers or
service centers can disassemble the product.
If any parts of your product require replacement for any reason, including
normal wear and tear or breakage, please contact us.
Keep the product away from liquids as exposition to liquids may cause
your wireless car charger to short-circuit. In case of exposition to liquid,
do not operate the charger.
Keep your product away from the reach of children. This product is not a
toy.
MAGNETIC WIRELESS
CAR CHARGER
AIR VENT MOUNT
WITH CLIP
SCREW
3.3 FT / 1 M
TYPE-C CABLE
USER’S MANUAL
2X
METAL PLATE
Connect your Nautica Magnetic
Wireless Car Charger any USB-A
charging port or cigarette lighter
socket of your car or another
power source such as a power
bank via the included Type-C to
USB-A cable to start charging
your mobile phone.
Keep in mind that an adapter will
be required to connect to a
cigarette lighter socket.
Press down the switch of the attaching clip
to install your car holder on the air vent.
HOW TO MOUNT ON AIR VENT
HOW TO CHARGE YOUR PHONE
Place the included
screw and the ball joint
adapter as shown in
the illustration.
Insert the ball joint
adapter on the tip of
the air vent mount into
the socket at the back
of the wireless holder.
Adjust the screw.
HOW TO INSTALL
Input 5V / 2A, 9V / 1.67A, 12V / 1.5A
Input Power max 18W (QC2.0 / QC3.0)
Output 5V / 1A, 9V / 1A, 9V/1.5A
Output Power 15W / 10W / 7.5W / 5W
Max Transimission Distance 0.2 in / 5 mm
Material PC
Product Dimensions 3.93*2.55*3.5 in / 100*65*89 mm
Product Weight 3.17 oz / 90 g
Charging Port Type-C
Over Current Protection
Over Voltage Protection
Under Voltage Protection
Over Temperature Protection