ELEMENT + ESSENTIAL STRENGTH Lat Machine User manual 1 Downloaded from www.Manualslib.
Contents Identification of the manufacturer and the equipment............... 3 Description of the equipment..................................................... 4 Technical data............................................................................ 5 Safety labels and warnings........................................................ 6 Place of installation.................................................................... 7 Unpacking......................................................................
Identification of the manufacturer and the equipment The identification plate of the equipment and manufacturer, affixed on the frame behind the weight stack, gives the following details: A B C D E Name and address of the manufacturer CE Mark Serial number Cautions and maximum user weight Equipment classification A B D ELEMENT+ SILVER-BLU AVI CB350C0 - ALK0GGGK Controllare periodicamente lo stato di usura Peso MAX utente: 180 kg Peso MX di lavoro: vedi pacco pesi Tipo: IC EN957 - 1/2 Maximum user’s b
Description of the equipment Seat (A): where the user sits to perform the exercise. Bar (B): moved by the user to perform the exercise. B Rollers (C): allow you to use workloads equal to or higher than body weight. Their position is adjustable in depth by means of the rollers lever (D) after having released it by operating the button positioned on it. Weight stack (E): the bar, operated by the user, moves the weights along two guides by means of a cable.
Technical data 1202 mm (47") 799 mm (31") 1205 mm (47") 1421 mm (56") Lat Machine Downloaded from www.Manualslib.
Safety labels and warnings The equipment does not have any sharp corners. All the parts which come into contact with the body are adequately protected with rubber coverings or padding. Warnings During all operations involving transport, maintenance and cleaning, pay attention to any part of the equipment where body parts may become trapped. It is important to pay attention to the labels affixed to the equipment, as they provide information about possible risks and hazards.
Place of installation To guarantee safe, comfortable and effective use of the equipment, the place of installation must comply with certain specific requirements; in particular, before choosing where to install the equipment it is recommended to check the following: - temperature between +10°C and +25°C; - sufficient ventilation to maintain a humidity level between 20% and 90%, when the equipment is in use; - adequate lighting, so that the physical exercise takes place in pleasant and relaxing conditio
Unpacking The equipment is supplied fully assembled in a carton and protected by cellophane wrapping, and secured to a pallet. The equipment can be lifted and handled using normal lifting machine. In order to ensure the safety of persons and property, carefully determine the lifting and handling machine used as a function of the place of installation.
Lifting and handling the equipment To move the equipment, use normal lifting and handling machine. Warning The equipment must be moved with great care, due to the risk of it tipping over. Lift the equipment from the weight stack side, as shown in the figure. Warnings Given the weight of the equipment, we recommend that more than one person be involved in lifting it. It is recommended to place some padded material between the frame and the lifting machine. Lat Machine Downloaded from www.Manualslib.
Routine maintenance Warnings The safety of the equipment is assured only on condition that it is carefully inspected for signs of damage and/or wear every two weeks. Replace defective and worn components immediately, or alternatively remove the equipment from service. The equipment should always be kept clean and free of dust, in compliance with good hygiene practice, especially if it is used in a gym or by more than one person. To clean the padded parts, use a moist cloth or a sponge and mild soap.
Replacing the padded components If any of the padded components show signs of wear, it is advisable, especially in the interests of hygiene, to replace them completely. In order to replace the seat loosen the screws on the opposite side to the padding. In order to replace the roller pads remove the cover (A) and unscrew the screw (B); then remove the washer (C) and the roller pads. A B Lat Machine Downloaded from www.Manualslib.
Replacing the cable To replace the cable, proceed as follows: - dismantle the bar; A - raise the rubber gaiter (A); - unscrew the screws (B) and extract the cable from the attachment (C); C - back off the lock nut (D) and unscrew the adjuster (E); - extract the cable from the adjuster side; B E Lat Machine Downloaded from www.Manualslib.com manuals search engine D cont.
Replacing the cable - insert the new cable beginning on the adjuster side (follow the original path of the cable as shown in the figure); - insert a thickness of approx. 10 mm (1/2”) under the first weight of the weight stack; Lat Machine Downloaded from www.Manualslib.com manuals search engine cont.
Replacing the cable - put in the adjuster (E); - insert the rubber gaiter (A) and the attachment (C), then tighten the screws (B); A - lower the rubber gaiter (A); - adjust the cable tension and tighten the lock nut (D); C - remove 10 mm thickness (1/2”) from the weight stack. B Warning ALWAYS use cables supplied directly by Technogym. The cables must always be replaced at the first sign of wear, even if it only affects the outer rubber protection.
Adjusting cable tension It is possible to take up some of the slack in the weight stack cable using the adjuster (E), after loosening the lock nut (D). E D Warning To pull the cable taut after replacement, it may be helpful, when tightening the screws (A), to insert a thickness of approx. 10 mm (1/2”) under the first weight in the weight stack. A Lat Machine Downloaded from www.Manualslib.
Replacing the spring hook Warning Once a month, carefully check the conditions of the spring hook. Always replace the spring hooks as soon as you notice the slightest signs of wear, deformity, difficulty closing, or anything else that may interfere with its robustness. When replacing, always use a spring hook supplied directly by Technogym.
Technical Service The Technogym Technical Support Service provides: - telephone assistance; - definition of service calls covered and not covered by warranty; - on-site assistance; - sending of original spare parts. Technogym Technical Support Service tel: 0547 650650 fax: 0547 650150 email: service@technogym.
Storage If the equipment will not be used for a prolonged period, it is recommended to store it: - in a clean and dry place, covered with a cloth to protect it from dust; - in an environment with a temperature between +10°C and +25°C and a humidity between 20% and 90%. For correct storage, use the original packing materials.
Using the equipment Sit down and position your legs underneath the roller pads. To adjust the height of the roller pads release the rollers lever (A) by operating the button positioned on it. Select the workload with the pin (B). Grasp the bar evenly. B A Lat Machine Downloaded from www.Manualslib.com manuals search engine cont.
Using the equipment Pull the bar down; make sure that your spine does not bend during the exercise. Maintain a smooth controlled speed through the movement while staying in control of the weight. At the end of the exercise return the weight stack to the starting position. Lat Machine Downloaded from www.Manualslib.
