. INTRODUCTION Overview…………………………………………………………………………..………………...……... 2 Main Features……………………………………………………………………………... ...………... ....4 2. EASY INSTALLATION GUIDE...…………...…………...…………...…………...……….. .. 3 3. SAFETY Instructions.………………………………………………………………………… …6 4. CHECK POINTS BEFORE USE……………………………………………………………… 7 Accessories Satellite Dish 5. CONTROLS/FUNCTIONS……………………………………………………………………….8 Front/Rear panel Remote controller Front Display 6. EQUIPMENT CONNECTION……………………………………………………………....
INTRODUCTION OVERVIEW This combo receiver is designed for using both free-to-air and encrypted channel reception. Enjoy the rich choice of more than 20,000 different channels, broadcasting a large range of culture, sports, cinema, news, events, etc. This receiver is a technical masterpiece, assembled with the highest qualified electronic parts. MAIN FEATURES • High Definition Tuners : DVB-S/DVB-S2 Satellite & DVB-T Terrestrial Compliant • DVB-S/DVB-S2 Satellite Compliant(MPEG-II/MPEG-IV/H.
EASY INSTALLATION GUIDE Part 1 Using the Preinstalled Satellite & Channel list This receiver is preinstalled with Satellites and default Channels and is fully configured. No settings need to be changed. After turning ON the receiver, select a language. Go to system setting and Factory Reset Menu. If you select Restore default channels, You can use preinstalled default channel list. How to add/delete Satellites Press the MENU button on the remote and go to Installation. Press OK on the Installation setup.
How to Install a New Satellite(Fixed Non-Motorized System) Press the MENU button on the remote and press the OK button on Installation setup. Press OK on satellite to display a Satellite List. To add a satellite, press the YELLOW( ) button on the remote. Press the EXIT button on the remote to exit the list. When the quality bar is at its highest level, press the RED( )button on the remote to scan the satellite. You can see Search popup menu. Press OK button to search channels.
How to restore default channels Press the MENU button on the remote. Go to Factory Reset and insert PIN Code(default 0000) Then go to Restore default channels, press OK button on the remote. Select YES It will retrieve default channels.
Safety Instructions 1. Be sure to read this User's Manual before starting the operation of the receiver. 2. Do not touch a power cord with wet hands as it may cause electric shock. 3. Never open the cover. It is very dangerous to touch the inside of the unit due to the possibility of an electric shock. 4. Place the unit in a well ventilated and no-heat environment. 5. When you do not use this unit for a long time, make sure that the power cord is pulled out from the outlet.
CHECK POINTS BEFORE USE ACCESSORIES If any accessories listed above are missing, contact the sales representative where you purchased this unit. SATELLITE DISH You dish should be properly installed and azimuth and elevation must be precisely set up. This unit is working with DiSEqC 1.2 on a compatible antenna positioner. Ask your dealer for more information.
CONTROLS/FUNCTIONS FRONT/REAR PANEL Watching TV status (Live mode) 1. Power 2. Menu 3. Exit 4. Volume +/5. OK 6. Channel +/- Connector 1. CABLE IN 2. LOOP OUT 3. LNB INPUT 4. LNB OUTPUT 5. LAN 6. USB 7. e-SATA 8. RS232 9. HDMI 10. SPDIF 11. S-VIDEO 12. Component Out 13. VIDEO 14. Audio L/R Out 15. TV/VCR SCART 16. RF OUT UHF 17. TV ANT IN 18. Power Cord OSD operating status (OSD mode) Turns the receiver on/off. To enter or exit the Main Menu. To change a previous menu or live mode.
REMOTE CONTROL 1. POWER : To turn the receiver On/Off. 2. MUTE : To turn the Sound On/Off. 3.TV/SAT : To switch the TV output source between the satellite input and the UHF/VHF antenna input. 4. ZOOM : To zoom In/Out. 5. EDIT : To go to Edit Channels Menu. 6. UHF : To adjust UHF channel. Use Volume key ◀/▶ to control UHF Channel 7. TV/RADIO : To Switch between TV and Radio modes. 8. MOSAIC : To display multiple pictures. 9. SLEEP : To adjust the Sleep Timer. 10. PAUSE : To pause the video.
FRONT DISPLAY 1 Power On/Off mode 2 It is displayed when a Satellite channel is viewing 3 It is displayed when a Terrestrial channel is viewing 4 It is displayed when a USB device is connected.
EQUIPMENT CONNECTION CONNECTION WITH ANTENNA / TV SET / A/V SYSTEM 1. Connect the TV antenna to TV ANT IN. 2. Connect the Video and Audio of TV to the Video and Audio. Connect Red and White connector to Audio R and Audio L and Yellow into video port respectively. 3. Connect the Component Video of your TV to Component Video of best quality. Connect the Y, Pb and Pr of your TV to Y, Pb and Pr respectively. 4. Connect your satellite dish.
OPERATION GETTING STARTED Turn your receiver power on and proceed with system setup as follows: Menu Language Setting 1. Turn on your TV and receiver. 2. The language selection menu will be displayed, select a language and press the OK button on. Installation Setup 1. Press the MENU button on the remote to display the main menu. 2. Use ◀/▶ and ▲/▼ button on the remote to move in the menu. 3. Select Installation Setup, the Installation Setup menu will appear. 4. Select each menu you want to edit /change.
Motorized Setup 1. Press the MENU button on the remote to display the main menu. 2. Use ◀/▶ and ▲/▼ buttons on the remote to move in the menu. 3. Select Motorized Setup, the Motorized Setup menu will appear. 4. Select each menu you want to edit /change - Satellite : Select any satellite by pressing ◀/▶ buttons on the remote. - Transponder : Select the current TP value of the selected satellite. - DiSEqC Motor : Select DiSEqC Motor type Off/DiSEqC 1.2/USALS 5.
USALS System Setup 1. Select USALS on DiSEqC Motor, the USALS menu will appear. - - - Satellite : Select any satellite by pressing ◀/▶ buttons. Transponder : Displays the current TP value of the selected satellite. DiSEqC Motor : Select DiSEqC Motor USALS. Position setting : set the current degree of the selected satellite by press OK button • Longitude degree : set the longitude degree of user position. • Longitude direction : set the longitude direction of user position.
Auto Navigation All the available channels/satellites can be searched in this menu. Select the satellite and save before Auto Search. 1. Press the MENU button on the remote to display the main menu. 2. Use ◀/▶ and ▲/▼ button on the remote to move in the menu. 3. Select Auto Navigation, Auto Navigation menu will appear. 4. Select the satellites you want to search by pressing the OK button on the remote. You can select more satellites by pressing the ◀/▶ and OK button on the remote. 5.
Advanced Search To edit and search channels on newly launched satellites or not preprogrammed satellites in the list. 1. Press the MENU button to display the main menu. 2. Use ◀/▶ and ▲/▼ buttons to move in the menu. 3. Select Advanced Search, the Advanced Search menu will appear. 4. Select each menu you want to edit/change. • Search TPs : Press RED ( ) button to search ‘Selected’ TPs. • Delete TPs : Press GREEN ( ) button to delete ‘Selected’ TPs.
- Channel : Select Channel Number for scanning. - Transponder : Display Frequency of selected Channel. - Bandwidth : Display Bandwidth of selected Channel. - Scan Mode : Select search type (Free+CA, Free Only, CA Only) - Network Scan : Select Network Search On/Off. - Radio CH : Search TV channels only or All(TV+Radio) channels. - Antenna Supply 5V : Select external voltage (5V) output. 4. Single Scan : Press RED ( ) button to search a current channel. 5.
■ AUDIO You can press AUDIO button to select audio language provided by service provider. ■ TEXT The Teletext service is a text data service sometimes available from the Service Provider. ■ SAT Press the SAT button to select a satellite in the Satellite List. ■ FAV Press FAV button to select a favorite channel list in the favorite group. ■ PAUSE You can press this key to pause to video, Press it again to resume the video.
■ WIDE Press the WIDE button to change the TV’s Aspect Ratio directly. 4:3 : Pan-Scan or Letter Box or Full-Frame 16:9 : Center-Cut-Off or Pillar Box or Full-Frame ■ COLOR Adjustment Press the COLOR button on the remote to select Color Adjustment menu. By using the ◀/▶ button on the remote, you can adjust the brightness, contrast and the color of picture. ■ POS In case of setting DiSEqC Positioner or USALS, You can use POS button for adjust current motor position.
TIME SETUP This submenu arrows you to set your local time - Time : Display current date and time. - GMT-Time: Sat : Display GMT date and time using satellite stream information. - GMT-Time: Terrestrial : Display GMT date and time using terrestrial stream information. - GMT Usage : If you turn it ON, local time is determined by adjusting the differences from GMT (Greenwich Meantime), according to your location. - Time Zone : If GMT Usage is ON, The Local time is GMT time +Local Offset.
- Lock Level : If you select INSTALL, you will be asked to enter PIN when you go to installation/edit channels/EDIT button. If you select MENU, you will be asked to enter PIN when you go to menu. - Age Limit : Prevents children or unauthorized people from watching the specific programs. (Not use/Every/4/7/13/16/18) - Old Pin : Enter current password to change password. - New Pin : Enter the new password you want to change. - Verify Pin : Enter new password to confirm. *Note : The default pin is 0000.
IP Settings If the Network supports DHCP, IP settings can be allocated automatically, If the Network does not support DHCP, the Addresses must enter manually.(Static IP). - DHCP Usage : On/Off to receive IP settings automatically. - IP Address : Here enter the IP address. - Subnet Mask : Here enter Subnet Mask Number from your Network. - Gateway : Here enter IP address of Gateway (e.g. router) - DNS : Here enter IP address of main DNS Server. - Mac Address : Mac address display.
2. Select Edit Favorites, Favorite Edit menu will appear. - EDIT( ) : If you want to edit the favorite name, press Red button on the remote. At favorite name menu, press OK button for virtual keyboard. - NEXT LIST( ) : Press Green button to toggle Favorite 1~8 / Favorite 9~16 List - CH CHANGE( ) : If you press Yellow button, You can change channel using numeric buttons. - SELECT FAV( ) : Press Numeric number( ) to make favorite list. You can use OK button to make same favorite list.
Front Display Settings This sub-menu allows you to control front display. 1. Press the MENU button on the remote to display the main menu. 2. Select Front display settings, Front display settings menu will appear. - Text Moving : Turn the text moving On/Off. - Channel Number : Turn the channel number On/Off - LED : Turn the blue light On/Off - VFD : Control VFD Display light 0 / 1 / 2 / 3 - Power Save : Control Power saving mode of standby state.
CAM(COMMON INTERFACE MODULE) Only CAM Initializing To watch scrambled channels, you will need a Conditional Access Module(CAM) and Smart card which is specific to that CAM from the service provider (broadcaster). *Note : Without a CAM and a smart card, you can watch only Free-to-Air programs. 1. Insert a CAM into a CAM slot in the receiver and a Smart card into the CAM. 2. The message : CAM In it will appear. Status of the CAM 1. Go to CI Information.
System Information You can check the current information about your receiver, such as the receiver Model name, Hardware version, Software version, hardware version, Last update, etc. *Note : This information is necessary when you want to download a new software or you need to repair the receiver. USB Menu This sub-menu allows you to do File & Disk management for internal or external memory device.
MP3 Menu 1. Use ▲/▼, OK button to select the MP3 file that you want to listen 2. Use ◀/▶ button to select Icon in the MP3 Player box. 3. Press the OK button to select a file. - ◀◀ : Previous MP3 file is played. - PLAY ( ) : Current MP3 file is played. - ▶▶ : Next MP3 file is played. - PAUSE ( ) : Current MP3 file is paused. - STOP ( ) : Current MP3 file is stopped. - REPEAT : Select One time / Repeat play for one file or current folder. - LIST : Open/Close the MP3 file list.
- DIR MODE/FILE MODE : You can view Dir/File view mode using this button. - TIME SORT/NAME SORT : You can sort files with Time or Name using this button. - LOOP PLAY/NORMAL PLAY : Use this button to view all file list one by one. - For full screen, press OK button once more and then following time-bar will appear. ▶ Edit Menu Enter the password. Press the YELLOW button. A popup menu will appear. Select the file that you want to edit, and set its parameters as desired. 1.
▶ RWD(Rewind) When playing the file, press the RWD button to rewind the program (adjust the playing speed). - Choose from : x2, x4 and x8 ▶ SLOW(1/2x, 1/4x) When playing the file, press the SLOW button to slow the speed of the playback. (adjust the playing speed) ▶ Bookmark To create a bookmark/chapter at a specific time/place of the file. - BOOKMARK : Press the BOOKMARK button and a red triangle will appear at that position.
Timer Recording This function is available when HDD or USB device is connected. You can choose a channel to record from the EPG Guide by using the INFO button. Time Shift 1. To pause and resume live TV channel, press the PAUSE button, The default time for Time-Shift is 30 minutes. 2. To resume live TV channel, press the PLAY button. 3. The trick-mode operations are available. To return to the live broadcast, press the ADVANCE button.
Explain how to download S/W by USB and how to upload and download channels by USB How to download S/W or Channel data by USB. 1. Insert USB Memory Stick to USB Port after opening Front Cover.(See below drawing) 2. Press MENU Key to go Main menu 3. Select USB Item and Go to USB Download & Upload. 4. Press OK to display USB- Download & Upload menu. 5. Press OK ▲/▼Key to select file for downloading. 6. Press GREEN Key to start download a selected file. 7. Press OK Key at Download Popup menu. 8.
HOW TO DOWNLOAD SOFTWARE FROM PC TO RECEIVER 1. Connect the null model cable to the RS-232C connection on the back of the receiver and to your PC. 2. Download the latest version of the TM Loader from the Technomate web site (www.technomate.com) 3. Download the latest software(.TBN) of your receiver. Ensure that the model number of the software is the same as the receiver you have. 4. Click on Browse in the TM Loader. 5.
Note. How to download/upload Channels If you want to download /upload Channels, Click on Channels in the TM Loader, then select Download/upload * Downloading Channels from PC to TM-8000 Series. 1. Click on Download, and then Click on Browse in the TM Loader. 2. Select the file from where you saved it. 3. Click on Connect in the TM Loader. 4. Turn on the satellite receiver 5. Once it displays 100% finished, the Channel downloading has finished. * Uploading Channels from TM-8000 Series to PC 1.
Trouble Shooting There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact the dealer. Don't open the receiver cover. It may cause a dangerous situation. Symptom Cause LED on front panel doesn't turn ON A/C power cord DISCONNECTED. Connect power cord properly into the power socket. Wrong connection of the Audio/Video output to TV input terminal.
Specifications System capabilities Satellite LNB/Tuner input Demodulator TERRESTRIAL System capabilities Tuner & Channel Decoder System resource Video decoder MPEG Audio Serial data interface Remote control SATA USB Ethernet PCMCIA Smart card Fully DVB compliant Connector Frequency range Signal level LNB supply LNB switch control DiSEqC Front end Symbol rate IEC 169-24, female 950MHz~2150MHz -65dBm~-25 dBm DC 13/18, max 400mA 22KHz Ver 1.0/1.1/1.
RF Modulator RF-Connector Frequency Output Channel TV Standard Audio Output Preset Channel 75ohm IEC169-2, Male/Female 470MHz to 860MHz CH 21-69 for the Demodulator PAL B/G/I/D/K Selectable by Menu Setting Mono with Volume Control CH 40, Software changeable by Menu screen Power Supply Input Voltage Type Power Consumption Protection Physical Specification Size (WxHxD) Weight AC90 to 240V, 50Hz/60Hz SMPS Max.
Glossary of Terms C band 3.7 ~ 4.2 GHz Frequency. Ku band 11 ~ 18GHz Frequency. DiSEqC Digital Satellite Equipment Control. LNB (Low-Noise Block converter) The LNB is an electronic unit mounted on the satellite dish. It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver. PID Package Identifier. PIN Code Personal Identification Number. Afour-digit code that is used for locking/unlocking. e.g. with the parental control feature.
