Explosion diagram specification 1 3 5 7 9 11 13 15 17 19 FL(CTP+LCM) 6.55HD+ H KF8 Black TM V1.0 F hsg asm KF8 Black PC+ 20%GF+Al-Tialloy F LED-Flash Seal Mylar 13.6*5.5*0.05 KF8 CAM AF 48M OV48B2Q A MOB 6P B SY V1.0 CAM FF 8M OV8856 A B 4PBG B TXD V1.0 48M R CAM Con Foams 15*11.9*0.15 KF8 PCBA MB H696 A1 64GB+4GB V1.0 FM con Foams 13.3*9 *0.4 KF8 MAIN CAM frame asm KF8 Black PC+20%GF FP BTB Imp Frame KF7 2 REC Deco part KF8 Black 4 DistanceSensorSeal Mylar10.5*5.5*0.
1 23 25 27 29 31 33 35 37 39 41 43 45 47 F CAM Cop foil 13*4.9*0.05 KF8 F CAM Location Frame KF8 Black PC 2M R CAM Rubber KF8 BlackBC FPC REC KF8 Coaxial cable KA7 RoHS 22 mc screw M1.4*L3.5*D2.5 *H0.5 silver mc Screw M1.4*L1.2*D3.5 *H0.4 Black Glue R CAM Lens 16M KF8 Glass 0.5mm Black CAM Deco KF8 Black PC SPK 1115 SPR H2.5 1.0W HS 32 DOWN frame asm KF8 Black PC+20%GF Motor Seal Mylar 12*5.5 *0.05 KF8 mc screw M1.4*L2.5*D2.5 *H0.5 silver glue PCBA SUB H696 1 A V1.
① 1. Front camera 2. Volume key 3.
1. Power off mobile. 2. Refer to the following picture for SIM / SD card installation.
to the computer using a USB cable (comes with the phone). 1. Please remind the front and back of the plug. 2. Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.
FCC Statement 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAR Information Statement Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is 1.329W/Kg and when worn on the body, as described in this user guide, is 0.519W/Kg(Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements).
of 10mm must be maintained between the user ’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited.
