AW4061 ADSL2+ WiFi Router User Manual Version 1.
REVISION HISTORY Revision 1.
AW4061 QIG Version 1.0 Page-1- 1. OVERVIEW The Quick Install Guide show you: 1. Hardware Connection 2. LED Status 3. Set Up Internet Access HARDWARE CONNECTION 1. POWER: Use only the included power adaptor to connector the POWER jack. The power adaptor is 15VDC@1000mA. 2. LAN1~4: Use the included Ethernet cable to connect a computer to the one of LAN port for Web setup and Internet access. 3.
AW4061 QIG Version 1.0 Page-2- LED STATUS After you have made the connections, push in the power button to power on the AW4061. 1. The POWER LED turns red light until AW4061 start up. When start up ready, the light change to green and stay on . 2. The ONLINE LED turns on while IP connected, and blinks while there is traffic. 3. The WLAN LED turns on while wireless active. 4. The DSL LED blinks then turns steady on when connection. 5.
AW4061 QIG Version 1.0 Page-3- SET UP INTERNET ACCESS 1. Login to AW4061 through Web Browser Configure your PC IP address automatically and DSN server automatically . In your browser, go to http://192.168.1.1 Enter the default login: Username: admin / Password: system 2. LAN Configuration You can choose LAN Interface to set IP address, subnet mask. 3. WAN Configuration There are three sub-menu for WAN configuration: [Channel Config], [ATM Settings], [ADSL Settings].
AW4061 QIG Version 1.0 Page-4- Set VPI /VCI and choose the Channel Mode.
AW4061 QIG Version 1.0 Page-5- If choose the PPPoE or PPPoA Channel Mode, you need configure the PPP Setting. Note: PPPoX can use default setting for DNS automatically. If choose the 1483 MEM or 1483 Routed Channel Mode, you need configure the WAN IP Setting.
AW4061 QIG Version 1.0 Page-6- Then you need click Services ->[DNS]->[DNS Server] and set the DNS manually. After finish the settings, go to the Admin->[Commit/Reboot] and click it to reboot AW4061. 4. Check ADSL Link Status There are two sub-menu for Statistic: [Interface], [ADSL].
AW4061 QIG Version 1.0 Page-7- 5. Wireless Configuration AW4061 is default enable for wireless service, so you didn’t need configure anything for using wireless. The default SSID is RTL867x-ADSL, you can get the access point on your computer. There are Five sub-menu for Wireless configuration: [Basic Settings], [Advanced Settings], [Security], [Access Control], [WDS]. Normally, [Basic Settings] and [Security] can be set usually.
AW4061 QIG Version 1.0 Page-8- SET UP Your Computer’s IP Address AW4061 is a ADSL Ethernet/Wireless Router which support DHCP and default enable. You also can set your computer IP Address as 192.168.1.x within the same subnet as AW4061 (AW4061 default IP is 192.168.1.1) and subnet mask (default is 255.255.255.0). 1. Click start > Control Panel 2. In the Control Panel, double-click Network Connections 3. Right-click Local Area Connection the click Properties 4.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2001 Safety of information technology equipment - IEEE Std.
Česky [Czech] [TECOM CO., LTD] tímto prohlašuje, že tento [AW4061] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [TECOM CO., LTD] erklærer herved, at følgende udstyr [AW4061]] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [TECOM CO.
Slovensko [Slovenian] [TECOM CO., LTD] izjavlja, da je ta [AW4061] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [TECOM CO., LTD] týmto vyhlasuje, že [AW4061] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [TECOM CO., LTD] vakuuttaa täten että [AW4061] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Regulatory Approvals FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
