HD3011/HD3010 User Manual Version: 2.0 Release Date: FEB 4th, 2015 Broadband Network Solution Department TECOM CO., LTD.
Ver. 2.0 Safety Precautions Please follow these safety precautions to prevent injury or damage to property that may be caused by fire or electrical damage. DOs: 1.) Use the type of power recommended as seen on the label of your device. 2.) Use the power adapter in the product package. 3.) Pay attention to the power load of the outlet or prolonged lines. An overburdened power outlet, damaged lines or plugs may cause electric shock or even fire.
Ver. 2.0 Northern America FCC Statement This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause interference to radio communications. This equipment as been tested and found to comply with the limits for a Class B computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against radio interference when operated in a commercial environment.
Ver. 2.0 Revision History Version 2.0 Date 2015‐02‐04 HD3011/HD3010 User Manual Update Log 2ed version for HD3011/HD3010 User Manual.
Ver. 2.0 Table of Contents 1. PRODUCT OVERVIEW........................................................................................... 6 2. INSTALLATION........................................................................................................ 7 2.1. APPEARANCE .................................................................................................................. 7 3. HD3011/HD3010 WEB CONFIGURATION ......................................................... 16 3.1.
Ver. 2.0 1. PRODUCT OVERVIEW HD3011/3010/3000 Series, ITU‐T G.hn networking standard compliant Ethernet/Wireless adapter, provides the best quality data transmission for the truly high‐speed ‘connected home’ experience. It allows users to extend a local area network via existing power lines, eliminating the need for extra wiring. Installation at home (or in a small office) is quick and easy as the HD3010/3000 Series come with plug‐and‐play technology.
Ver. 2.0 2. Installation Included devices are: One HD3000 device One HD3011/HD3010 device One Ethernet cable 2.1. Appearance HD3000 Device Front Panel There are 3 LED’s on the front panel of HD3000 that show the status of the unit.
Ver. 2.
Ver. 2.0 Item Define 1 Power Color Function In case of a regular device: (Sigma chipset define) Green The LED will blink if identifies a Domain Master till completion of registration (very short time period) and shall be Solid ON (Green) after registration In case of Domain Master device: The LED will be solid ON (Green) 2 Ethernet “Blink”, indicates data transmission.
Ver. 2.0 HD3011 device Front Panel There are 6 LED’s on the front panel that show the status of the unit.
Ver. 2.0 The side panels contains Ethernet port and USB ports Item Define 1 Power LED Color Function In case of a regular device: The LED will blink if identifies a Domain Master till completion of registration (very short time period) Green and shall be Solid ON (Green) after registration In case of Domain Master device: The LED will be solid ON (Green) 2 Link LED In case of Domain Master device: The LED will be solid ON (Green) if is a standalone Domain Master device.
Ver. 2.
Ver. 2.0 There are 5 LED’s on the front panel that show the status of the unit.
Ver. 2.0 Item Define 1 Power LED Color Function In case of a regular device: The LED will blink if identifies a Domain Master till completion of registration (very short time period) Green and shall be Solid ON (Green) after registration In case of Domain Master device: The LED will be solid ON (Green) 2 Link LED In case of Domain Master device: The LED will be solid ON (Green) if is a standalone Domain Master device.
Ver. 2.0 Green 6 WLAN LED Steadily On – WLAN enable Off ‐ WLAN disable Flashes ‐ traffic passing through Green Label Function WPS/WLAN Button ‐WPS (Wi‐Fi Protected Setup) encryption if press WPS button more than 2 seconds. ‐Enable / Disable WIFI function if press WPS button at least 5 seconds. Reset Button ‐The device restarts if you press the reset button for less than 3 seconds ‐The factory defaults press the rest button for more than 5 seconds. All settings will be lost.
Ver. 2.0 3. HD3011/HD3010 Web Configuration 3.1. Login Page Figure3.1‐1 shows the login window. Here, the login information should be filled in as shown below: Figure 3.1‐1 The default IP address of the HD3011/HD3010 LAN is 10.10.10.254 Username: admin Password: admin After login we can see Quick Setup page 3.2.
Ver. 2.0 Figure3.2‐1 displays the Quick setup page of the device. Figure 3.2‐1 Using quick setup we can configure below list.
Ver. 2.0 3.3. Basic Setup Figure3.3‐1 shows basic setup of the device Figure 3.
Ver. 2.0 3.3.1. Operation Mode Figure3.3.1‐1 displays operation mode settings Figure 3.3.
Ver. 2.0 3.3.2. LAN Figure3.3.2‐1 and Figure3.3.2‐2 displays LAN settings information page These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. Figure3.3.
Ver. 2.0 Figure3.3.2‐2 DHCP Server DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives out IP addresses when a device is booting up and request an IP address to be logged on to the network. That device must be set as a DHCP client to obtain the IP address automatically. By default, the DHCP Server is enabled. The DHCP address pool contains the range of the IP address that will automatically be assigned to the clients on the network.
Ver. 2.0 UPnP is a distributed, open networking standard that uses TCP/IP for simple peer‐to‐peer network connectivity between devices. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network. In turn, a device can leave a network smoothly and automatically when it is no longer in use. UPnP broadcasts are only allowed on the LAN.
Ver. 2.0 3.3.3. WAN Figure3.3.3‐1, Figure3.3.3‐2, Figure3.3.3‐3 and Figure3.3.3‐4 displays WAN settings information WAN has static, DHCP, PPPoE and 3G connection types. Configure static connection type as below Figure3.3.
Ver. 2.0 Configure DHCP connection type as below Figure3.3.
Ver. 2.0 Figure3.3.3‐3 PPPoE Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection. Please enter the information accordingly. Username: Enter your username for your PPPoE connection.
Ver. 2.0 Figure3.3.
Ver. 2.0 3.3.4. Wireless Figure3.3.4‐1 and Figure3.3.4‐2 displays basic wireless information The following page is Wireless LAN settings. Please select and input the correct information in the following item to set Wireless function.
Ver. 2.0 Figure 3.3.4‐1 Figure 3.3.4‐2 We can configure below settings using basic wireless settings page SSID: The SSID is a unique name to identify the DSL Router in the wireless LAN. Wireless clients associating to the DSL Router must have the same SSID. Broadcast SSID: Select No to hide the SSID such that a station can not obtain the SSID through passive scanning. Select yes to make the SSID visible so a station can obtain the SSID through passive scanning.
Ver. 2.
Ver. 2.0 3.4. Advanced Setup Figure3.4‐1 shows Advanced Setup menu list Figure 3.
Ver. 2.0 3.4.1. Advanced Wireless Figure3.4.1‐1, Figure3.4.1‐2, Figure3.4.1‐3 shows Advanced Wireless settings and Wi‐Fi multimedia The following page is Advanced Wireless settings. Please select and input the correct information in the following item to set Wireless functions. Figure 3.4.
Ver. 2.0 Figure 3.4.1‐2 Figure 3.4.
Ver. 2.0 Beacon Interval The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network. DTIM This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM).
Ver. 2.0 3.4.2. Security Figure3.4.2‐1, Figure3.4.2‐2, Figure3.4.2‐3, and Figure3.4.2‐4 shows wireless Security information Figure 3.4.2‐1 Figure 3.4.
Ver. 2.0 Figure 3.4.2‐3 Figure 3.4.
Ver. 2.0 Using this page we can set SSID choice, Security mode, Access Policy and WPA. Security Mode OPEN WEP WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. Select Disable to allow all wireless computers to communicate with the access points without any data encryption. Select 64‐bit WEP or 128‐bit WEP to use data encryption. Key#1~Key#4 The WEP keys are used to encrypt data.
Ver. 2.0 also supports passphrases, it does so only as a way to more easily create static keys, which are usually comprised of the hex characters 0‐9 and A‐F. WPA Algorithms TKIP TKIP stands for “Temporal Key Integrity Protocol.” It was a stopgap encryption protocol introduced with WPA to replace the very‐insecure WEP encryption at the time. TKIP is actually quite similar to WEP encryption. AES AES stands for “Advanced Encryption Standard.
Ver. 2.0 3.4.3. WPS Figure3.4.3‐1, Figure3.4.3‐2 shows WPS settings Wi‐Fi Protected Setup (WPS; originally Wi‐Fi Simple Configuration) is a network security standard that attempts to allow users to easily secure a wireless home network but could fall to brute‐force attacks if one or more of the network's access points do not guard against the attack. Figure 3.4.
Ver. 2.0 Figure 3.4.3‐2 WPS Settings There two WPS mode, one is PIN code and other one is PBC. PIN method in which a personal identification number (PIN) has to be read from either a sticker or display on the new wireless device. This PIN must then be entered at the "representant" of the network, usually the network's access point. Alternately, a PIN provided by the access point may be entered into the new device. This method is the mandatory baseline mode and every WPS‐certified product must support it.
Ver. 2.0 Example of configuration 1. Make sure WPS is enabled on system wise. 2. For Pin method 1). Select radio button PIN method. 2). Enable your Wi‐Fi client (Notebook, Mobile, PAD…etc). And check WPS. 3). Take PIN at client and specify same one in your AP device. 4). Click “Apply“below “WPS Progress” table to trigger WPS session. 5). Once connected, “WPS current status” will be put “Connected”.
Ver. 2.0 3. For PBC at Web 1). Select the following radio button, and click “Apply” Button to trigger WPS session. 2). at Wi‐Fi client side, select PBC method. Within 2 minutes, they are automatically connected. 3). Once connected, “WPS current status” will be put “Connected”. 4. For physical PBC on the housing: 1). Special Note: WPS is enabled on system wise. 2). At wifi client side, select PBC method. 3). Within 2 minutes, please push physical PBC button at housing.
Ver. 2.0 3.4.4. Station List Figure3.4.4‐1 display the wireless network station list Figure 3.4.
Ver. 2.0 3.4.5. Routing Figure3.4.5‐1, Figure3.4.5‐2 displays Static Routing Settings Figure 3.4.5‐1 Figure 3.4.
Ver. 2.0 3.4.6. Port Forwarding Figure3.4.6‐1, Figure3.4.6‐2 displays Port Forwarding setup and information Figure 3.4.
Ver. 2.0 Figure 3.4.
Ver. 2.0 3.4.7. DMZ Settings Figure3.4.7‐1 displays DMZ settings page The De‐Militarized Zone (DMZ) is a network which, when compared to the LAN, has fewer firewall restrictions, by default. This zone can be used to host servers (such as a web server, ftp server, or email server, for example) and give public access to them. The eighth LAN port on the router can be dedicated as a hardware DMZ port for safely providing services to the Internet, without compromising security on your LAN.
Ver. 2.0 3.5. Management Figure3.5‐1 displays Management Menu List Figure 3.
Ver. 2.0 3.5.1. TR069 Settings Figure3.5.1‐1 displays TR069 Settings page Note: If device is in bridge mode ACS server should also be in the same subnet of LAN address else ACS server will fail to connect with the device. The following web page is TR069 setting page. It can set ACS Server information for TR069. Please select and enter the correct parameters in this page setting. Figure 3.5.
Ver. 2.0 3.5.2. NTP Settings Figure3.5.2‐1 displays NTP Settings page Figure 3.5.
Ver. 2.0 3.5.3. Upgrade Firmware Figure3.5.3‐1 displays Upgrade firmware information page Notice: We only can upgrade firmware using LAN IP address of the web interface. Web interface with WAN IP address will not allow upgrading firmware. You can upgrade the firmware of the device in this page. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to browse the local hard drive and locate the firmware to be used for the update. Figure 3.5.
Ver. 2.0 3.5.4. Upgrade PLC Firmware Figure3.5.4‐1 displays Upgrade PLC firmware information page You can upgrade the PLC firmware of the devices paired. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to browse the local hard drive and locate the firmware to be used for the update. Figure 3.5.4‐1 Upgrade PLC firmware function will update all devices which are in the same network.
Ver. 2.0 3.5.5. System Restart Figure3.5.5‐1 displays system restart page Figure 3.5.
Ver. 2.0 3.5.6. System Management Figure3.5.6‐1 displays system management setting page The current system settings can be saved as a file onto the local hard drive. The saved file or any other saved setting file can be loaded back on the device. To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used. You may also reset the device back to factory settings by clicking on load factory default settings. Figure 3.5.
Ver. 2.0 3.5.7. Administrator Settings There is only one account that can access Web‐Management interface. It is admin. Admin has read/write access privilege. In this web page, you can set new password for admin. Figure3.5.7‐1 display administrator settings information page Figure 3.
Ver. 2.0 3.6. Status Figure3.6‐1 displays Status Menu List Figure 3.
Ver. 2.0 3.6.1. Device Status Figure3.6.1‐1 displays Device status information This page displays the current information for the device. It will display the system info, Internet configuration, LAN information. Figure 3.6.
Ver. 2.0 3.6.2. DHCP Client Status Figure3.6.2‐1 displays DHCP Client Status information This page displays DHCP Client Status information for the device. Figure 3.6.
Ver. 2.0 3.6.3. PLC Interface Status Figure3.6.3‐1 and Figure3.6.3‐2 displays PLC interface status page This page displays PLC interface status page information for the device.
Ver. 2.0 Figure 3.6.3‐1 Figure 3.6.3‐2 PLC device have Master information and slave information. It will support to display 10 slaves information.
Ver. 2.
FCC Warning 15.21 Information to users Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. 15.105 Information to users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
