QUICK START GUIDE Cisco Universal Small Cell 7330
Revised: November, 2013, 78-21441-03 Table of Contents 1 About Your Small Cell 2 Before You Begin 3 Safety Instructions 4 Connect Your Small Cell 5 Mount Your Small Cell Mounting on a Wall or Hard Ceiling Mounting on a Suspended Ceiling Mounting on a Suspended Ceiling Using an Existing Bracket Mounting in a Plenum Space 6 Verify that Your Small Cell is Operating Correctly 7 Declarations of Conformity and Regulatory Information 8 Specifications 9 Obtaining Documentation and Submitting a Ser
1 About Your Small Cell The Cisco Universal Small Cell (USC) 7330 is an indoor small cell that provides Wideband Code Division Multiple Access (WCDMA) coverage and capacity to public areas where macro networks are not cost-effective. The USC 7330 supports up to 16 active third-generation (3G) users and supports Band 2/5 for the American market and Band 1 for the rest of the world.
Cisco USC 7330 Top View 3 2 1 1 Power LED 2 Ethernet connection LED 3 Status LED 4 External antenna port 4 4 361429 Figure 1
2 Before You Begin Consider where you want to install your new small cell. The ideal location is: • somewhere central, away from windows—this will allow your small cell to provide the best possible coverage. • at least one 30 cm (1 foot) from other wireless broadcasting devices to avoid possible interference. • where you can connect to your broadband router or cable modem. Decide whether you will mount your small cell on a wall or ceiling, or whether you will place it on a desktop or other flat surface.
3 Safety Instructions Translated versions of the following safety warnings are provided in Cisco USC 7330 Regulatory Compliance and Safety Information, located on Cisco.com. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Statement 1005 Warning Do not operate the unit near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.
Caution The fasteners you use to mount an access point on a ceiling must be capable of maintaining a minimum pullout force of 20 lbs (9 kg) and must use all indented holes on the mounting bracket. Caution This product and all interconnected equipment must be installed indoors within the same building, including the associated LAN connections as defined by Environment A of the IEEE 802.af Standard. Note Your small cell is suitable for use in environmental air space in accordance with section 300.22.
4 Connect Your Small Cell Figure 2 Cisco USC 7330 Connections 6 5 3 2 1 361430 4 1 10/100 Base-T Ethernet port supporting PoE+ 2 Power port 3 GPS port (available on Band 2/5 only) 9
4 Reset button 5 2G external antenna port for the Band 1 small cell (USC7330-T1-K9) or UMTS Band V external antenna port for the Band 2/5 small cell (USC7330-T2-K9) 6 3G external antenna port for the Band 1 small cell (USC7330-T1-K9) or UMTS Band II external antenna port for the Band 2/5 small cell (USC7330-T2-K9) Step 1 Connect one end of the network cable to the small cell Ethernet port and the other end to your broadband router or cable modem.
Step 5 5 Wait ten minutes for your small cell to be ready to use. The status LED stops flashing green and becomes solid green when your small cell is ready to use. Mount Your Small Cell Mounting on a Wall or Hard Ceiling If you need to mount your small cell on a wall or hard ceiling, hang it on two screws projecting from the surface. Attach the screws to the wall or ceiling such that the distance between the screws matches the distance between the mounting holes on the back of your small cell.
Cisco USC 7330 Mounted Vertically on Wall 380785 Figure 3 12
Mounting on a Suspended Ceiling If you need to mount your small cell on a suspended ceiling, follow these steps: Step 1 Place your small cell on a clean, flat surface with the bottom side facing you. Step 2 Take two screws from the accessory kit and screw them into each of the two corresponding holes on the bottom of the small cell. Step 3 Attach the suspended ceiling bracket to the ceiling rail system using the two “L” brackets included in the accessory pack and eight screws.
Cisco USC 7330 with Suspended Ceiling Bracket 381277 Figure 4 14
Figure 5 Screw the provided security locking screw into place to lock the bracket into position.
Mounting on a Suspended Ceiling Using an Existing Bracket If you have an existing Low-Profile AP bracket (AIR-AP-BRACKET-1) attached to a suspended ceiling that you want to use for your Cisco USC 7330, perform this task: Step 1 Connect the suspended ceiling bracket to your small cell as described in Mounting on a Suspended Ceiling, page 13: perform Step 1, Step 2 and Step 4 to Step 6. Step 2 Screw the four metal feet into the four corresponding holes on the bottom of the suspended ceiling bracket.
Suspended Ceiling Bracket with Attached Feet 361434 Figure 6 Step 3 Attach the USC 7330 small cell to the Low-Profile AP bracket (AIR-AP-BRACKET-1) as described in Access Point Mounting Instructions: http://www.cisco.com/en/US/partner/docs/wireless/ access_point/mounting/guide/apmount.html Step 4 Fasten a padlock to secure the small cell to the brackets and prevent theft. See “Securing the Access Point to the Mounting Plate” for more information.
1 1 18 Padlock Cisco USC 7330 with Padlock Attached 361436 Figure 7
Mounting in a Plenum Space To mount your small cell in a plenum space, you have two options: 1. Connect the suspended ceiling bracket to a secure location in the plenum space and then connect your small cell to the suspended ceiling bracket as described in Mounting on a Suspended Ceiling, page 13: perform Step 1, Step 2 and Step 4 to Step 6. 2. Connect your small cell to the suspended ceiling bracket as described in Mounting on a Suspended Ceiling Using an Existing Bracket.
Table 1 USC 7330 Status LED Indications LED Indication Small Cell State/Action Off No power—ensure power supply is connected and turned on Fast Green Initialization or provisioning—wait for this action to complete Green In service with no calls or data sessions—ready to support calls Slow Green In service with active calls or data sessions Red Flash 1 times in 4 seconds No connection to local broadband router—verify the connection between the broadband router and your small cell and verify that t
Table 1 USC 7330 Status LED Indications (continued) LED Indication Small Cell State/Action Red Initial boot—wait up to 20 minutes; if the state does not change, perform a reset Cannot create secure connection—contact customer support Internal fault—small cell has a fault and cannot provide service RF issue, cannot select an RF profile—verify whether another small cell is located in close proximity and if so, relocate the unit Provisioning failure—contact customer support 7 Declarations of Conformity an
The USC7330-T1-K9 carries the CE Mark: Class B Notice for FCC Modifying the equipment without Cisco’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
• Support for 16 CS and PS simultaneous users • Support for HSDPA: 14.4 Mbps downlink, 5.7 Mbps uplink UMTS operating and network listen band options – Band I (2100) [EU] – Band II (1900) and Band V (850) [US] • GSM network listen band options – Band III (1800) and Band VIII (900) [EU] – Band II (1900) and Band V (850) [US] • Maximum transmit power UMTS – 24 dBm (energy consumption < 12 Watt) • Sensitivity: -113 dBm • UL sensitivity compliant to 3GPP TS25.
• Storage temperature: 23 to 113 degrees F (–5 to 45 degrees C) • Humidity: 5% to 90% (noncondensing) • Desktop/wall/ceiling mountable • Green initiative compliant to RoHS External Antenna Requirements Before attaching an external antenna to your small cell, note the following requirements: Table 2 UMTS Antenna Requirements Gain 0 dBi mean; < 2 dBi peak Ripple +/- 2 dB Azimuth Beamwidth Omni Elevation Beamwidth Omni Isolation: UMTS to GSM listen UMTS to WLAN > 15 dB > 15 dB Feed System Coaxial
Table 2 UMTS Antenna Requirements (continued) Polarization Linear Connector type MMCX 50 Ohm Table 3 GSM Antenna Requirements Gain 0 dBi mean az plane; < 2 dBi peak Ripple +/- 2 dB Azimuth Beamwidth Omni Elevation Beamwidth Omni or similar to vertical mounted dipole; nulls at θ=0 and 180 degrees are acceptable Isolation: GSM to UMTS listen GSM to WLAN > 15 dB > 15 dB Feed System Coaxial feed Return loss < -6 dB over band specified Power rating > 0 dBm Polarization Linear Connector
GPS Antenna Requirements The GPS antenna port supports an active antenna with a 50-Ohm SMB connector. 9 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.
Americas Headquarters Cisco Systems, Inc. San Jose, CA Asia Pacific Headquarters Cisco Systems (USA) Pte. Ltd. Singapore Europe Headquarters Cisco Systems International BV Amsterdam, The Netherlands Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
