PL-606 FM stereo / SW / MW / LW DSP RECEIVER OPERATION MANUAL www.tecsunradio.
CONTROL LOCATIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Power Band* & ATS VM & SCAN VF & SCAN ETM (Easy Tuning Mode) Delete Memory Display & Lock & Snooze FM ST. & AM BW Alarm Time FM & SW Telescopic Antenna FM & SW Antenna Jack Earphone Jack USB 5V DC-Jack Multifunctional Tuning Knob Stand Volume Knob Battery Compartment The unit is shut down the long-wave band before out of the factory.If you want to open the long-wave band in the off state, press MW button 10 seconds.
LCD DISPLAY 1.Battery consumption indicator / Charging indicator 2.Sleep timer indicator 3.Alarm on/off indicator 4.Key-lock indicator 5.Temperature (Temp.
Installing batteries 2. Press the [POWER] button to turn on/off the radio. Note: If the radio is unable to be turned on. Please check if the batteries were installed correctly, " displays battery capacity is sufficient or the lock function had been applied with " on screen (press & hold the [ ] button to unlock.) TUNE IN STATIONS Press the [POWER] button to turn on your radio, then select your desired band by pressing the [FM], [MW]、SW[ ] or [ ] button.
frequencies. you can easily tune into your desired stations from those preferred frequencies. 1. Press the [ETM] button with [ETM] shows on screen to enter Easy Tuning Mode. 2. Press & hold the [ETM] button until the frequency start running to auto scan and store stations into ETM memory, within the present band. 3. When the frequency stop running, turn around the [TUNING] knob to select those stored stations.
2.Press & hold the [VF] button with [ ] advancing to scan from one station to another, staying on each station for about 5 seconds. 3.To stop the auto browse function, simply press the [VF] button. Note: While operating the “Auto Browse Station” function, you can press the [M] button anytime to store the station into memory, and the radio will keep on auto browsing the next available station. WORKING WITH STATION MEMORIES There are total 550 preset memories within the unit.
2. Press the [MEMORY] button with “preset” flashing 3. Press the [MEMORY] button again to store the station into memory. You can also wait for 3 seconds to auto store the station into memory. METHOD 3: SEMI-AUTO STORING STATION While operating the “Auto Browse Station” function, you can simply press on the [MEMORY] button to store the station into memory to avoid storing unwanted stations and interfering signals. 1. Press the [VF] button to switch into frequency mode. “ advancing to auto browse from one 2.
delete function automatically. METHOD 2: SEMI-AUTO DELETE MEMORY Feature: using the Auto-Browse function of memory to quickly delete unwanted station. 1. Press the [VM] button to enter the memory mode. 2. Press & hold the [VM] button with [PRESET] flashing to auto scan from one memory to another, staying on each station memory for about 5 seconds. 3.
WORKING WITH ALARM SETTING THE ALARM TIME 1. Press & hold the [ALARM] button with hour flashing in the upper right corner, then rotate the [TUNING] knob to adjust the hour. 2. Press the [ALARM] button with minutes flashing, then rotate the [TUNING] knob to adjust the minute. 3. Press the [ALARM] button again, then rotate the [TUNING] knob to select from 1 ~ 90 minutes to set the Auto Alarm Off Timer. 4. Press the [ALARM] button to confirm the setting. 5.
Press & hold it again with the “ deactivate the locking function. ” symbol disappears to FM ST. (FM STEREO) ” appears While listening to FM stereo stations, press the [FM ST.] button with “ in the display to activate the ”STEREO ” listening. If the received FM broadcast signal is too weak, it is recommendable to turn off the stereo function by pressing the [FM ST.] ” disappears. button again with “ Note: The stereo function will not be activated if the FM station is not stereo broadcasting.
TURN ON/OFF THE CHARGING FUNCTION & EXCHANGE THE BATTERY CONSUMPTION DISPLAY: With radio off, press & hold the [ ] key with “ ”& “ ” show up to activate the consumption display of rechargeable batteries and the “ shows up and built-in charging system. Press & hold the [ ] key with “ “ ” disappears to activate the consumption display of regular batteries and turn off the built-in charging function. Note: This radio is default to use regular batteries for power supply.
METHOD 2: Plug in the external wire antenna to the [FM & SW] antenna jack of this radio, and then hang its end outside the window for better reception of FM and SW. IMPORTANT MATTERS FOR USING BATTERIES 1. If no battery has been installed inside for long time, clock of radio would stop to work. However, pre-stored frequencies are still kept. Clock would work again after new batteries being re-installed inside. 2.
capacity of power incorrectly. 4. In case of radio not to be used for a long period, draw out the batteries for preventing liquid leakage and damaging the parts of radio. TROUBLE SHOOTING QUESTIONS ANSWERS SOLUTIONS Can not turn on the radio. -No power with the batteries. -Didn't install the batteries properly. -Replace the new batteries. -According to "+" or "-" sign to install the batteries again. -Press the [ ] button to unlocked. -Power button is locked. Radio goes off when you are listening.
preset frequency. radio malfunction. This may caused by interference, and the computer microchip not function properly. Remove the battery, then you can reload. If it is still not able to work, please contact your nearest dealer for customer service. SPECIFICATIONS 1. Frequency range FM MW LW SW 2. Sensitivity FM (S/N=30dB) MW (S/N=26dB) LW (S/N=26dB) SW (S/N=26dB) 3. Selectivity FM MW LW SW 4. FM Stereo crosstalk 5. Memory 6. Output (Distortion 10%) Speaker Earphone 7. Power 8. Speaker 9.