MATRIX® 570V T S E T U P Software version 1.
COPYRIGHTS © 2011 TeeJet Technologies. All rights reserved. No part of this document or the computer programs described in it may be reproduced, copied, photocopied, translated, or reduced in any form or by any means, electronic or machine readable, recording or otherwise, without prior written consent from TeeJet Technologies. TRADEMARKS Unless otherwise noted, all other brand or product names are trademarks or registered trademarks of their respective companies or organizations.
Matrix® 570VT ● ISOBUS Table of Contents CHAPTER 1– PRODUCT OVERVIEW 2 OPTIONAL SYSTEM COMPONENTS 3 CONFIGURATIONS 5 POWER ON/OFF 7 Start Up Sequence.......................................................................................................................................... 7 GENERAL OPERATION INFORMATION 8 CHAPTER 2 – SYSTEM SETUP CULTURE 9 10 Units......................................................................................................................................
Matrix® 570VT ● ISOBUS CHAPTER 1– PRODUCT OVERVIEW The Matrix 570VT is designed to provide years of service under typical agricultural operating conditions. A tight fitting enclosure, combined with rubber covers for all connectors mean that typical dusty environments will not cause operational problems. While occasional splashing of water will not damage the unit, the Matrix 570VT is not designed for direct exposure to rain. Take care not to operate the Matrix in wet conditions.
Matrix® 570VT ● ISOBUS OPTIONAL SYSTEM COMPONENTS IC18 Sprayer/NH3 ECU Use with your existing VT or Matrix® 570VT • Works seamlessly and displays on any ISOBUS VT • Easy navigation menu and data rich display • IC18 Sprayer ECU suitable for use with NH3 and liquid fertilizer • Automatic boom section control upgrade option • Variable rate control available providing your VT has GPS and task control capability • Add additional ISOBUS ECUs as your needs change • Provides basic rate control • Standardized plugs
Matrix® 570VT ● ISOBUS BoomPilot Electronic Control Unit for IC18 BoomPilot (automatic boom section control) is possible in combination with software built into the IC18 Sprayer/NH3 Electronic Control Unit (ECU). The ECU should be combined with the appropriate cable to interface with your BoomPilot system, spray controller and/or spraying machine for quick and easy installation.
Matrix® 570VT ● ISOBUS CONFIGURATIONS The following diagrams are reflective of typical Matrix 570VT in combination with the IC18 Job Computer configurations. Due to the variety of possible configurations, these should be used for reference purposes only.
Matrix® 570VT ● ISOBUS Figure 1-7: IC18 Sprayer TeeJet Retro Kit to Matrix 570 VT Harnessing.
Matrix® 570VT ● ISOBUS POWER ON/OFF Press the POWER BUTTON Sequence. to power on the console. Upon power up, the Matrix VT will begin its Start Up Press and briefly hold the POWER BUTTON Figure 1-8: Power Button (until the screen turns black) to power off the console. Power Button USB Port with Rubber Cover Start Up Sequence The console takes approximately 40 seconds to power up. During this time the TeeJet Technologies logo will be displayed (brightness levels will fluctuate).
Matrix® 570VT ● ISOBUS GENERAL OPERATION INFORMATION A firm touch is required when selecting a screen icon. For rapid adjustment of a setting, press and hold the UP/DOWN ARROW ICONS All changes are saved automatically. The console needs to be cycled off and back on when changing or attaching equipment to the Matrix system. Press the icon of any menu item to display a definition of that item. To remove the information box, press anywhere on the screen.
Matrix® 570VT ● ISOBUS CHAPTER 2 – SYSTEM SETUP System Setup is used to configure cultural and console settings. NOTE: All settings are automatically saved when selected. Figure 1-11: Master Screen To access the System Setup screens: 1. Select MATRIX VT SETUP KEY from Master Screen. 2. Select from: ►Culture – used to configure Units , Language and Time Zone .
Matrix® 570VT ● ISOBUS CULTURE Culture is used to configure Units, Language and Time Zone settings. Figure 1-13: Culture 1. Press CULTURE ICON . 2. Select from: ►Units – defines the system measurements ►Language – defines the system language ►Time Zone – establishes the local time zone OR Press PAGE RIGHT ARROW to cycle through all settings. NOTE: Options labels are current settings. While in a setting screen, press icon to view available factory settings and setting ranges.
Matrix® 570VT ● ISOBUS Language Figure 1-15: Language Languages defines the system language. 1. Press CULTURE ICON . 2. Press LANGUAGE ICON . 3. Press UP/DOWN ARROW ICONS to change between languages. 4. Press ►PAGE RIGHT ARROW to proceed to Time Zone. ►SYSTEM SETUP TAB to return to main System Setup screen. NOTE: Press & hold UP/DOWN ARROW ICONS to quickly adjust settings. Time Zone Figure 1-16: Time Zone Time zone establishes the local time zone. 1. Press CULTURE ICON . 2. Press TIME ZONE ICON . 3.
Matrix® 570VT ● ISOBUS CONSOLE Console Setup is used to configure Volume, LCD Brightness, Virtual Terminal Number and Screen Calibration settings, as well as view About information and Save system software information. Figure 1-17: Console 1. Press CONSOLE ICON . 2.
Matrix® 570VT ● ISOBUS LCD Brightness Figure 1-19: LCD Brightness LCD Brightness adjusts the brightness of the console display. Range is 0 - 100. 1. Press CONSOLE ICON . 2. Press LCD BRIGHTNESS ICON . 3. Press the UP/DOWN ARROW ICONS to adjust LED brightness. • Higher the number, the brighter the LCD • Lower the number, the dimmer the LCD 4. Press ►PAGE RIGHT ARROW to proceed to VT Number. ►SYSTEM SETUP TAB to return to main System Figure 1-20: Touch Screen Calibration Setup screen.
Matrix® 570VT ● ISOBUS Touch Screen Calibration Touch Screen Calibration is used to activate a touch screen calibration. 1. Press CONSOLE ICON . 2. Press CALIBRATE TOUCH SCREEN ICON . 3. Press HAND ICON to enable the touch screen calibration process. 4. “Begin touch screen calibration?” Press ►Yes – to begin the Touch Screen Calibration. ►No – to return to the Touch Screen Calibration screen 5. Press series of 5 crosshairs . 6. Press OK to complete the touch screen calibration. 7.
Matrix® 570VT ● ISOBUS About/Save About/Save screen displays the system software version Figure 1-23: About Matrix 570G as well as the software versions of modules connected to the CAN bus. To view system information: 1. Press CONSOLE ICON . 2. Press ABOUT ICON to view data including: • Unit Model Number • Software Version • Connected Modules 3. Press ►CHECKERED FLAG to complete Console Setup. ►SYSTEM SETUP TAB to return to main System Figure 1-24: About Verification Setup screen.
Matrix® 570VT ● ISOBUS APPENDIX A - TIME ZONES Africa Abidjan Accra Addis Ababa Algiers Asmara Bamako Bangui Banjul Bissau Blantyre Brazzaville Bujumbura Cairo Casablanca Ceuta Conakry Dakar Dar es Salaam Djibouti Douala El Aaiun Freetown Gaborone Harare Johannesburg Kampala Khartoum Kigali Kinshasa Lagos Libreville Lome Luanda Lubumbashi Lusaka Malabo Maputo Maseru Mbabane Mogadishu Monrovia Nairobi Ndjamena Niamey Nouakchott Ouagadougou Porto-Novo 16 Sao Tome Tripoli Tunis Windhoek America Adak Ancho
Matrix® 570VT ● ISOBUS Katmandu Krasnoyarsk Kuala Lumpur Kuching Kuwait Macau Magadan Makassar Manila Muscat Nicosia Novosibirsk Omsk Oral Phnom Penh Pontianak Pyongyang Qatar Qyzylorda Rangoon Riyadh Saigon Sakhalin Samarkand Seoul Shanghai Singapore Taipei Tashkent Tbilisi Tehran Thimphu Tokyo Ulaanbaatar Urumqi Vientiane Vladivostok Yakutsk Yekaterinburg Yerevan Atlantic Azores Bermuda Canary Cape Verde Faroe Jan Mayen Madeira Reykjavik South Georgia St Helena Stanley Australia Adelaide Brisbane Broke
MATRIX® 570VT S E T U P 1801 Business Park Drive Springfield, Illinois 62703 USA Tel: (217) 747-0235 • Fax: (217) 753-8426 www.teejet.
