NEW! Follow along with your smartphone to make assembly even easier! Page 5 EZ-Up™ Chin-Up & Inversion Rack and System Assembly Instructions FULL W AR Y 5 YEAR RA N T * Specifications may vary from this image and are subject to change without notice. To download and print Teeter’s EZ-Up™ Chin-Up & Inversion Rack Instructions, visit the product support page at teeter.com.
Congratulations on your purchase of the Teeter EZ-Up™ Chin-Up Inversion Rack! This product has been designed as a multi-functional fitness tool, to be ideally paired with Teeter EZ-Up™ Gravity Boots to ensure the most comfortable and effective inversion experience.
BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before use. Carefully adhere to the Instructions to help ensure safety and product integrity. The below warnings and subsequent instructions assume use of the Inversion Rack with Teeter’s EZ-Up Gravity Boots. Be sure to also review the materials that accompany the Gravity Boots.
Items for Assembly Instructions Items not shown to scale. Hardware drawings located on the insert inside each Hardware Kit. Carefully remove the individual parts from the carton. You should have all of the items listed below. If any items are missing or damaged, contact your retailer or Teeter Customer Service directly. ITEM NAME ITEM NO. ITEM NO.
Understanding Your EZ-Up Rack Before reading further, study the drawing below to familiarize yourself with the important assembled components of your EZ-Up Rack.
Safety Warning Labels & Product Specifications Important: Please review all labels and supporting materials before using your EZ-Up Rack. This drawing indicates the locations of the warning labels found on your product. If a label is missing, illegible or removed, contact Teeter Customer Service to request a complimentary replacement label. Note: Image and labels below not shown at actual size. 25 in (63.5 cm) 9 in (22.9 cm) ! WARNING SERIOUS INJURY OR DEATH MAY OCCUR.
Before Beginning Assembly Unpack and Prepare Your Workspace • Unpack all parts and support materials. Set aside packing materials and clear your work area. • Locate the Hardware Kits, packaged with the manuals. They are labeled to correspond with the assembly process. • The Getting Started DVD provides step-by-step instruction on how to assemble and use your product. You may find it helpful to follow along with the DVD by watching it on either your TV or computer.
STEP 1 Assemble Large Diameter Bars FIGURE 1 1 FIGURE • Locate the three (3) bars for the Large Bar Assembly, marked with Joint numbers 1, 2, and 3 (Figure 1). Locate the Large Assembly Hardware Kit (E11060). 1 2 • Position the Large Diameter “L” Bar and Large Diameter “Elbow” Bar together, aligning joints marked as 1 and joints marked as 3 (Figure 2). 2 • Assemble Joint 1 (Figure 2A): 3 1 3 » Seat the curved flange at the end of the “Elbow” Bar over the hole on the “L” Bar.
STEP 2 Assemble Small Diameter Bars • Locate the three (3) bars for the Small Bar Assembly, marked with Joint numbers 4, 5, and 6 (Figure 4). Locate the Small Assembly Hardware Kit (E11061). FIGURE 4 5 4 • Position the Small Diameter “L” Bar and Small Diameter “Elbow” Bar together, aligning joints marked as 5 and joints marked as 6 (Figure 5). • Assemble Joint 5 (Figure 5A): » Seat the curved flange at the end of the “Elbow” Bar over the hole on the “L” Bar.
STEP 3 Attach Large & Small Assemblies FIGURE 7 • Align and slide the Small Bar Assembly (labeled 4, 5, 6) into the Large Bar Assembly (labeled 1, 2, 3) (Figures 7 & 8). • The width of the EZ-Up Rack may be adjusted by sliding the Small and Large Assemblies in or out (Figure 9), to fit doorways between 28 in - 36 in (71 - 91.4 cm) wide. For purpose of assembly, slide to the narrowest width. FIGURE 8 FIGURE 9 8 • SECURELY TIGHTEN ALL BOLTS and NUTS (3 on each side) using a screwdriver and wrench.
STEP 4 Install Locking Brackets ! WARNING FIGURE1011 FIGURE Serious injury or death may occur if the Inversion Rack is not installed in the doorframe properly: ALWAYS securely install the Locking Brackets in SOLID WOOD doorways built according to U.S. national building codes (maximum width of 36 in/91.4 cm). Maximum height allowance depends on the height of the doorway and placement of the locking brackets. In a standard 6’8” (203.2 cm), maximum user height is 7’3” (221 cm).
STEP 5 Install the EZ-Up Rack into Doorframe • With the Upper Bar facing you, hold the EZ-Up Rack near the ends of the Lower Bar. Slide the flared end of the Large Straight Bar into the U-Shaped Rest in the RIGHT locking bracket (Figure 12). FIGURE 12 • Extend the length of the EZ-Up Rack until the flared end of the Small Straight Bar can slide into the U-Shaped Rest in the LEFT locking bracket, NOT to exceed 36 in (91.4 cm) wide.
STEP 6 Attaching & Storing the EZ-Up Strap • Once the Rack is fully assembled and mounted to the doorframe, loop the EZ-Up Strap over the Lower Bar (Figure 14A). FIGURE 14A • Feed the large-looped end of the strap through the small-looped end and pull until the fit is snug around the lower bar (Figure 14B).
STEP 7 Test Weight and Height ! WARNING FAILURE to test and inspect the equipment prior to first use could result in serious injury or death! Weight Test FIGURE 16A • After installing the Locking Brackets and securing the EZ-Up Rack in place, the user and another adult person with a combined weight equal to or greater than 1.
FULL 5 YEAR WARRANTY The Teeter warranty set forth below and on Teeter’s website applies to US and Canadian customers only. For international customers, please consult your local distributor for warranty information which will vary depending on country.
If you have any trouble assembling the equipment, or questions about its use, please contact customer service. USA: 800-847-0143 or info@teeter.com International: info@teeterintl.com Roger Teeter Founder & Innovator USA: Teeter 9902 162nd St. Ct. E. Puyallup, WA 98375 Toll Free: 800-847-0143 Fax: 800-847-0188 teeter.com | info@teeter.com Check out the selection of products and accessories available at teeter.com! International: Teeter International, Ltd.
