User Manual

STEP
3
Assemble Seat
FIGURE 9
FIGURE 10
FIGURE 11
Seat Installation
• Locate the Lower Seat and place it upside-down on a flat
surface, such as the edge of a table. Locate the Seat Back
Assembly and line it up with the Lower Seat.
• Use the Step 3a Hardware Kit to assemble the seat parts.
Hand tighten 4 × Bolts with 4 × Spring Washers and 4 × Washers
as shown. Proceed to fully tighten the Bolts with the Allen
Wrench (Figure 9).
• Before attaching the assembled Seat to the Seat Post, make
sure the Seat Post is fully raised for better access, then line the
Seat up with the Seat Post (Figure 10).
• Use the Step 3b Hardware Kit to attach the Seat. Hand tighten
4 × Bolts with 4 × Spring Washers and 4 × Washers as shown.
Proceed to fully tighten the Bolts with the Allen Wrench (Figure 11).
REVISIONS
ENGR DATE REV SHT ZONE DESCRIPTION
NMS 10/18/2017 A 1 8D A1: RELEASE FOR PATENT
PARTS LIST
ITEM QTY NET DIMENSIONS/DESCRIPTION NOTE MATERIAL SHT
REVISION STATUS
SHT 1
REV A
8
A
1234567
D
C
B
C
A
D
B
5 3 16 248 7
Teeter_STRIDER ASSEMBLY 201703
SHEET 1 OF 1
REV FILE NAME
TITLE:
NICK SOLLER
ENGR
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
DRAWN
FINISH
AS PROCURED
UNLESS NOTED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: FULL SIZE:
D
A
EXPECTATIONS LLC
PUYALLUP, WA 98391
TOLERANCES
UNLESS NOTED
=
.1
=
.03
= .005
=
1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
8
A
1234567
D
C
B
C
A
D
B
5 3 16 248 7
Teeter_STRIDER ASSEMBLY 201703
SHEET 1 OF 1
REV FILE NAME
TITLE:
NICK SOLLER
ENGR
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4
DRAWN
FINISH
AS PROCURED
UNLESS NOTED
.X
.XX
.XXX
ANGLE
EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC
SCALE: FULL SIZE:
D
A
EXPECTATIONS LLC
PUYALLUP, WA 98391
TOLERANCES
UNLESS NOTED
=
.1
=
.03
= .005
=
1
NICK SOLLER
FILLET RADII: .005-.010
CORNER BREAK: .005-.010
ALL DIMENSIONS IN INCHES
108
9
8
Bolt
Spring Washer
Washer
108
9
8
Bolt
Spring Washer
Washer
Step 3a Hardware
Step 3b Hardware
8