NEW! Follow along with your smartphone to make assembly even easier! FitSpine X Series Assembly Instructions TM Models X1, X2, X3 For gravity-assisted stretching and decompression FULL 5 YEAR T Y W AR RA N To download and print the Teeter FitSpine X™ instructions, visit the Product Manuals page at teeter.com. EN * Specifications may vary from this image and are subject to change without notice. The X1 is shown here. Your actual model may vary.
Congratulations on your purchase of a Teeter FitSpine X™ Series Inversion Table! For the best experience, it is critical that you follow the assembly instructions, read and fully understand the Owner’s Manual attached to the equipment, and review the Getting Started DVD prior to using your new Teeter Inversion Table. Teeter Decompression Devices are multiple user, reusable devices for home use, intended to provide traction to the spine while stretching the para-spinal muscle and soft tissues.
BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table. Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity. IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE ! WARNING FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.
Parts for Assembly Parts vary by model (noted) and are not shown to scale. Hardware drawings located on the insert inside each Hardware Kit. ITEM NO. ITEM NAME ITEM NO.
Understanding Your Inversion Table Before reading further, study the drawing below to familiarize yourself with the important components of your Teeter Inversion Table. 1 2 3 6 4 7 5 Located on back of table bed. 8 13 9 14 12 10 11 15 The X1 is shown here. Your actual model may vary.
Safety Warning Labels & Product Specifications Important: Please review all labels and supporting materials before using your inversion table. This drawing indicates the locations of the warning labels found on your product. If a label is missing, illegible or is removed, contact Teeter Customer Service to request a complimentary replacement label. Note: Image and labels below not shown at actual size. 60.5 in (153.7 cm) 58.0 in (147.3 cm) 28.8 in (73.2 cm) The X1 is shown here.
Before Beginning Assembly Unpack and Prepare Your Workspace • If possible, assemble the equipment at or near the space in which you intend to use it to avoid moving it later. • Unpack all parts and support materials. Set aside packing materials and clear your work area. • Locate the Hardware Kits packaged with the manuals. They are labeled to correspond with the assembly process. • The Getting Started DVD provides step-by-step instruction on how to assemble your product.
For X1 Models STEP 1 Assemble A-Frame Base & Stretch Assist Handles (X1 Models) FIGURE 1 LOCKED RIGHT LEFT 1 • Gently push down on the Spreader Arms to ensure they are fully open and in the “locked” position (Figure 1). 2 FRONT REAR • On a level surface, position the A-Frame so that it is standing upright and the Stability Feet are on the ground. FIGURE 1a • Look for temporary circular assembly assistance labels on the A-Frame.
For X2 & X3 Models STEP 1 Assemble A-Frame Base & Stretch Max Handles (X2 or X3 Models) • On a level surface, position the A-Frame so that it is standing upright and the Stability Feet are on the ground. • Gently push down on the Spreader Arms to ensure they are fully open and in the “locked” position (Figure 4). FIGURE 4 LOCKED RIGHT • Look for temporary circular assembly assistance labels on the A-Frame.
For All Models STEP 2 Assemble Table Bed • Locate the Table Bed Assembly Hardware Kit (HK1010). FIGURE 9 1 2 • Place the Table Bed face down on the floor and push down on the Support Beam, so the two holes align evenly with the holes at the base of the Upper Support Arms (Figure 9). You may have to exert extra pressure to ensure that the Support Beam slides over the rubber spacers. • Insert the two Bolts into the open holes (Figure 10). • Thread a Washer and Nut onto each Bolt and hand-tighten.
For All Models STEP 3 Assemble Roller Hinges to Table Bed NOTE: Some models come with Traction Handles pre-assembled to the Roller Hinges. The assembly instructions detailed below still apply. FIGURE 11 UNLOCKED • Familiarize yourself with the 3-Hole Roller Hinge and Cam Lock terms (Figure 11). ! WARNING NEVER disassemble the Roller Hinge Pivot Pin.
For ForAll AllModels Models STEP 4 Assemble Table Bed to A-Frame • Face the front of the A-Frame where the Crossbar is located (Figure 16). FIGURE 16 REAR • Grasp both Roller Hinges, right above the Cam Lock, and lift the Table Bed. Allow the top of the Table Bed to rotate toward the floor, so that the back of the Table Bed is now facing you and the top of the Table Bed is in front of the Crossbar (Figure 17).
For All Models STEP 5 Assemble Main Shaft to Table Bed • Your model’s Main Shaft may differ from what is shown in the figures, however the assembly instructions remain the same. FIGURE 20 • Facing the front of the A-Frame, hold the Main Shaft in your left hand with the height markings facing up. Slide the end of the Main Shaft into the Main Shaft Housing (Figure 20), located at the base of the Table Bed.
For All Models STEP 6 Attach Angle Tether & Head Pillow FIGURE 24 Attach Angle Tether • The tether will come pre-assembled to the A-Frame. • Unfold the adjustable tether and clip it to the U-Bar on the underside of the Table Bed (Figure 24). • Slide the buckle to lengthen or shorten the strap depending on your desired maximum angle of inversion.
For All Models Misassembly Check ! WARNING If your Teeter Inversion Table looks like either of these images, your inversion table has been misassembled and is unfit for use. Improper assembly could result in serious injury or death! Image A Go back to Step 3 for instruction. Demonstrates that the Roller Hinges have been assembled upside down into the Table Bed and must be corrected. Image B Go back to Step 4 for instruction.
For All Models Before Inverting FIGURE 26 Ensure Owner’s Manual is Attached The Owner’s Manual contains important information on how to use your Teeter Inversion Table, including how to personalize the user settings, properly secure and release the Ankle Lock System, and test and adjust the rotation control. • If not already attached, thread the provided metal chain through the pre-punched hole in the upper corner of the Owner’s Manual.
The Teeter warranty set forth below and on Teeter.com applies to the Inversion Table only. Accessories may come with their FULL 5 YEAR WARRANTY own terms. This warranty applies to US and Canadian customers only. For international customers, please consult your local distributor for warranty information which will vary depending on country.
Find These Great Products and More at teeter.com! T3 Massager P2 Back Stretcher Better Back Foam Rollers Better Back Neck Restore Better Back Vibration Cushion reNEW Muscles Pain Relieving Cream ™ ™ Countless options for self-massage, trigger point therapy, and myofascial release to resolve tension and pain gently and naturally. ™ Prepare the body for movement, accelerate recovery, minimize muscular imbalances, and improve overall flexibility with the Teeter collection of textured Foam Rollers.