GB F RCS RCT KR T IR Mod. FV21XX series AR www.tefal.
6 5 4 3 2 7 1 8 11 10 9
fig.1 fig.2 fig.3 fig.4 fig.5 fig.6 fig.7 fig.8 fig.
Description 1. 2. 3. 4. 5. 6. Spray nozzle Anti-calc valve Steam control Filling inlet Spray button Electric power cord 7. Thermostat indicator light and temperature setting indicator 8. Extra Stable Heel* (depending on model) 9. Thermostat dial 10. Tank max indicator 11. Soleplate *Your iron has been designed with an Extra Stable Heel (depending on model) for more safety.
If you have very hard • water, mix tap water with commercially available • demineralised water in the following ratio : - 50% tap water, - 50% demineralised water. What water to use ? GB Your appliance has been designed to function with untreated tap water. However, Self-cleaning of the appliance should be carried out once a month.
Spray Function • Whether steam or dry ironing, you are able to use the Spray button to dampen laundry to remove stubborn creases. (fig.6) Store your iron • Set the steam control to and unplug the iron. • Wait until the soleplate cools down and empty the tank. A little water may remain in the tank. • Wind the cord around the heel of the iron. • Store the cold iron on its heel (fig.7). Maintenance and cleaning Cleaning the anti-calc valve (once a month) • Unplug your iron and empty the water tank.
If there is a problem PROBLEM GB POSSIBLE CAUSE SOLUTION Water drips from the holes in the The chosen temperature is too low and does soleplate. not allow for the formation of steam. You are using steam while the iron is not hot enough. There is too much steam. You have stored the iron horizontally, without emptying it and without setting it to . You are using chemical descaling Brown streaks come through the holes in the soleplate and agents. stain the linen. You are not using the right type of water.
Description 1. 2. 3. 4. 5. 6. Spray Tige anti-calcaire Commande vapeur Orifice de remplissage Touche Spray Cordon d’alimentation 7. 8. 9. 10. 11. Voyant et repère réglage du thermostat Talon Extra Stable* (selon modèle) Bouton du thermostat Repère maxi du réservoir Semelle *Votre fer est conçu avec un talon Extra Stable (selon modèle) pour une plus grande sécurité.
Quelle eau utiliser ? • Votre appareil a été conçu pour fonctionner avec l’eau du robinet. Il est nécessaire Si votre eau est très calcaire, mélangez l’eau de procéder 1 fois par mois à l’auto-nettoyage de l’appareil.
Humidifiez le linge • Quand vous repassez à la vapeur ou à sec, appuyez plusieurs fois de suite sur la touche Spray pour humidifier le linge (ffig.6) et enlever les plis résistants. Rangez votre fer • Placez la commande vapeur sur et débranchez le fer. • Attendez que la semelle refroidisse et videz le réservoir. Un peu d’eau peut rester dans le réservoir. • Enroulez le cordon autour du talon du fer. • Rangez le fer froid sur son talon (ffig.7).
Un problème avec votre fer PROBLEMES CAUSES POSSIBLES SOLUTIONS L’eau coule par les trous de la semelle. La température choisie ne permet pas de faire de la vapeur. Vous utilisez la vapeur alors que le fer n’est pas assez chaud. Vous utilisez la commande Superpressing trop souvent. Le débit vapeur est trop important. Vous avez rangé le fer à plat, sans le vider et sans placer la commande vapeur sur . Vous utilisez des produits détartrants chimiques. Vous n’utilisez pas le bon type d’eau.