User's Guide

30
BIOS Setup option name Ty pe [Default] / Select Value Show Help string
Advanced Page Yes
► NCT6683D Super IO Configuration Yes System Super IO Chip Parameters.
Super IO Chip Information string NCT6683D Yes
► Serial Port 1 Configuration Yes Set Parameters of Serial Port 1 (COMA)
Serial Port Select item [Enabled] / Disabled Yes Enable or Disable Serial Port (COM)
Device Settings Board Infromation IO=3F8h; IRQ=4 Yes
Line separator
Serial Port Mode
Select item
1T/1R RS-422
/ [3T/5R RS-232]
/ 1T/1R RS-485 TX ENABLE Low Active
/ 1T/1R RS-422 with termination resister
/ 1T/1R RS-485 with termination resister
TX ENABLE Low Active
/ Disable
Yes
Select Serial Port Mode
►
Serial Port 2 Configuration
Yes Set Parameters of Serial Port 2 (COMC)
Serial Port
Select item [Enabled] / Disabled Yes Enable or Disable Serial Port (COM)
Device Settings Board Infromation IO=2F8h; IRQ=3
Yes
Line separator
Serial Port Mode
Select item
1T/1R RS-422
/ [3T/5R RS-232]
/ 1T/1R RS-485 TX ENABLE Low Active
/ 1T/1R RS-422 with termination resister
/ 1T/1R RS-485 with termination resister
TX ENABLE Low Active
/ Disable
Yes
Select Serial Port Mode
► Serial Port 3 Configuration
Yes Set Parameters of Serial Port 3 (COMD)
Serial Port Select item
[Enabled] / Disabled Yes Enable or Disable Serial Port (COM)
Device Settings Board Infromation IO=2F8h; IRQ=3
Yes
► Serial Port 4 Configuration
Yes Set Parameters of Serial Port 4 (COME)
Serial Port Select item
[Enabled] / Disabled Yes Enable or Disable Serial Port (COM)
Device Settings Board Infromation IO=2F8h; IRQ=3
Yes
►
Hardware Monitor Yes Monitor hardware status
Pc Health Status Header
Line separator
Hardware Monitor Alert Enable
Select item
Disabled / [Enabled] Yes
Hardware Monitor Alert Enable and Disable. If
monitored voltage/temperature/fan status are out of
range, BIOS displays warning message during
POST.
Line separator
VR_THRM_P1
Board Infromation + xx C Yes
System temperature2 Board Infromation + xx C Yes
AVSB Board Infromation +3.135~3.465 V Yes
VCC_MON Board Infromation +4.75~5.25 V Yes
VCC3_MON Board Infromation +3.135~3.465 V
Yes
VCORE_MON
Board Infromation +0.45~1.3 V Yes
V_SM_MON Board Infromation +1.045~1.155 V Yes
V_1P05
Board Infromation +0.099~1.103 V
Yes
VCCRTC Board Infromation +3.135~3.465 V Yes
VCC3 Board Infromation +3.135~3.465 V
Yes
3VSB
Board Infromation +3.135~3.465 V Yes
BACKUP_BAT_MON Board Infromation +3.0~4.2 V Yes
►
S5 RTC Wake Setting Yes Enable system to wake from S5 using RTC alarm
Wake System from S5
Information string [Disabled] / Fixed Time Yes
Enabler or disable System wake on alarm event,
Select FixedTime, system will wake on the
hr::min::sec specified.
Wake up hour
Text input [0] ~ 23 Depend
Select 0-23 For example enter 3 for 3am and 15 for
3pm
Wake up minute Text input [0] ~ 59 Depend
select 0 - 59 for Minute
Wake up second Text input [0] ~ 59 Depend select 0 - 59 for Second
► CPU Configuration Yes CPU Configuration Parameters
Intel® Pentium® CPU N4200 @1.10Ghz Information string Yes
CPU Signature
Board Infromation 506CA Yes
Microcode Patch
Board Infromation 1A
Yes
Max CPU Speed Board Infromation 1100 MHz Yes
Min CPU Speed
Board Infromation 800 MHz Yes
Processor Cores Board Infromation
4
Yes
Intel HT Technology Board Infromation Supported / Not Supported Yes
Intel VT-x Technology Board Infromation Supported / Not Supported Yes
Line separator
L1 Data Cache
Board Infromation 24 KB x 4 Yes
L1 Code Cache Board Infromation 32 KB x 4 Yes
L2 Cache Board Infromation 1024 KB x 2
Yes
L3 Cache Board Infromation Supported / Not Present Yes
64-bit Board Infromation
Supported
/ Not Supported Yes
Line separator Yes
Intel Virtualization Technology
Select item Disabled / [Enabled] Yes
When enabled, a VMM can utilize the additional
hardware capabilities provided by Vanderpool
Technology
Burst Frequency Select item Disabled / [Enabled] Yes
Burst Frequency.
► Network Stack Configuration Yes Network Stack Settings
Network Stack
Select item [Disabled] / Enabled Yes
Enable/Disable UEFI Network Stack
Ipv4 PXE Support
Text input [Disabled] / Enabled Depend
Enable Ipv4 PXE Boot Support. If disabled IPV4
PXE boot option will not be created
Ipv6 PXE Support
Text input [Disabled] / Enabled Depend
Enable Ipv4 PXE Boot Support. If disabled IPV6
PXE boot option will not be created