AUTOMATIC DRUM WASHING MACHINE USER MANUAL TKW 1070 Delay
03 - 09 TABLE OF CONTENTS BEFORE USE 10 - 15 USING THE APPLIANCE >COMPONENTS ............................... 03 >PREPARATION ................................ 04 >SAFETY INSTRUCTIONS ................... 05 >INSTALLATION ................................ 06 >CONTROL PANEL ............................ 08 16- 20 MAINTENANCE >PROGRAM SELECTION ..................... 10 >DISPLAY CODES ............................. 18 >CONSUMPTION AND TECHNICAL DATA .. 11 >TROUBLESHOOTING........................
BEFORE USE COMPONENTS 03 THANKS FOR PURCHASING A TEKA PRODUCT Please read these instructions carefully before using this appliance. The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance. Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance.
04 PREPARATION BEFORE USE PREPARING THE MACHINE Remove all the packing materials to prevent unsteadiness, including the polystyrene base. Upon opening the package, water drops may be seen on the plastic bag and the porthole. This is normal phenomenon resulting from water tests in the factory. DESCRIPTION This diagram may be slightly different from the layout of the washing machine you have just purchased due to technical improvements.
BEFORE USE SAFETY INSTRUCTIONS 05 BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME DO ... ... Make sure that the transport bolt are removed. ... Use a separate earthed socket for the power supply. ... Make sure that the plug is accessible. ... Hold the plug and not the electric cable when unplugging the power supply. ... Make sure that the fuses in the power circuit are rated for 15A. ... Keep away from heat sources and direct sun light to prevent plastic and rubber components from aging. ...
06 INSTALLATION BEFORE USE DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process. 1. Remove the back cover. 2. Remove the four bolts on the rear side and take out the synthetic stabilisers from within the machine. 3. Replace the back cover. 4. Fill the holes left by the bolts with blanking plugs. Note: 1.
07 BEFORE USE INLET HOSE 1. Connect the nut on the inlet hose to the connector on the water valve. 1. 2. 2. Apply inlet hose to a water tap with cold, fresh water. DRAIN HOSE 8 0 - 1 0 0cm Note: Use the hose-set supplied with the appliance. Old hose-sets should not be reused. 1. 1. Use the drain hose bracket to keep the end of the drain hose retained and prevent the outflow of water. Don't extend the length of the drain hose; if an extended hose is required, please consult a serviceman. 2. 2.
08 BEFORE USE CONTROL PANEL I G B H A E D J K F C A Program knob G Detergent distribution drawer B Power Switch H Display C Start/Pause button I ECO D Spinning Speed Setting button J Intense button E Washing temperature button K Extra rinse button F Delay Button OPERATIONAL FUNCTIONS A ¬ Program knob B ¬ Power Switch C ¬ Start/Pause Button D ¬ Spinning Speed Setting Button _By turning the knob clockwise/counterclockwise, the required program can be selected.
BEFORE USE F ¬Delay Button G ¬ Detergent distribution drawer H ¬Display I Eco J Intense button K Extra rinse button 09 Touch this button lightly, the washing machine will start operation after a period of time and the corresponding indicator will go on. The range is 0.5-24 hours; each touch of this button increases a half hour. After the button is set, press the Start/Pause button to start countdown of the set time (the time is displayed on the screen until the program ends).
USING THE APPLIANCE PROGRAM SELECTION PROGRAM MODES 2 1 Detergent compartment for prewash mode 3 2 Detergent compartment 1 3 Compartment for softener and other additives Temperature Maximum Preset Program 2 3 1 Recommended Laundry TKW 1070 1 ¬ Lana 30°C - - to 40 °C 30°C Woolen fabrics 400 rpm 2 ¬ Sintético 40°C - - to 60 °C 40°C Fast colour synthetic 1000 rpm 3 ¬ Eco 40°C - - to 90 °C 40°C Cotton fabrics 1000 rpm 4 ¬ Algodón 40°C - - to 90 °C 40°C Cotton fabrics
USING THE APPLIANCE CONSUMPTION AND TECHNICAL DATA CONSUMPTION TABLE The wash cycle times are intended as a guide only. The actual time used may vary due to different water pressure, initial water temperature, etc. MAX. LOAD ENERGY CONSUMPTION WATER CONSUMPTION TEMPERATURE PROGRAM WASHING TIME ¬ Lana 30°C 2 kg 0.34 kWh 55L 30°C 1:00 h ¬ Sintético 40°C 4 kg 0.71 kWh 50L 40°C 1:10 h ¬ Eco 40°C 4 kg 0.78 kWh 44L 40°C 1:18 h ¬ Algodón 40°C 7/8 kg 0.83 kWh 46.
WASHING METHODS PLEASE NOTE USING THE APPLIANCE This washing machine is for domestic use only. If the machine is use for commercial purpose the guarantee will not be valid anymore.Do not use it for purposes other than that for which it was designed. Follow the instructions given on the label of each garment and wash only machine-washable garments. POWER SUPPLY Connect the washing machine to the power supply (220V to 240V~/50Hz). WATER CONNECTION Turn on the tap. The water must be clean and clear.
USING THE APPLIANCE LOADING THE MACHINE Delay Open the washer door, put in the laundry piece by piece. Close the door tightly. ¬ When first using the washing machine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine. Before washing you should run the machine without laundry, but with detergent, with 60°C programm. ¬ Do not overload the washing machine.
USING THE APPLIANCE SETTING WASHING TEMPERATURE Press and hold down the temperature button until the desired temperature is selected . Delay SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected.See "Operational functions" on the "Control panel" pages (08 and 09) for selecting temperature and spin speed. It is advisable to select the recommended value. Delay WASHING Press the Start/Pause button. The washing machine will operate according to the preset programs.
USING THE APPLIANCE CARE CHART Resistant material Bleachable in cold water Don't dry clean Delicate fabric Do not bleach Dry flat Washable at 95 °C Iron at 200 °C Hung to dry Washable at 60 °C Iron at 150 °C Dry on clothes hanger Washable at 40 °C Iron at 100 °C Tumble dry, normal heat Washable at 30 °C Don't iron Tumble dry, reduced heat Hand wash Dry cleaning with any solvent Don't tumble dry Dry clean only Dry cleaning with pericloride Wool Seal Dry cleaning with aviation fuel
CLEANING & CARE MAINTENANCE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash. Open the washer door to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace the drain hose. 1. 2. CLEANING THE DETERGENT DRAWER 1. Clean the detergent distribution drawer regularly. Swing out the drawer, flush it clean with water and then replace it. 2.
WATER INLET VALVE AND INLET VALVE FILTER To prevent blockage to the water supply by ingress of foreign substances, clean the water inlet valve and inlet valve filter regularly. MOVING THE MACHINE If the machine is to be moved to a distant location, replace the transportation bolts removed before installation to prevent damage as shown below. 1. 2. 3. 4. 5. Remove the blanking plugs. Remove the back cover Insert the synthetic stabilisers and the transportation bolts. Tighten the bolts with a spanner.
DISPLAY CODES MAINTENANCE DISPLAY CODES AND SPECIAL FUNCTIONS CODES CAUSES SOLUTIONS Err1 Err2 ¬ Door is not properly shut. ¬ Drainage error, water not emptied within 6 minutes. ¬ Temperature sensor not properly connected or damaged. ¬ Heater error (Appears at the end of a cycle). ¬Water level not met in 8 minutes. _ Shut the door properly. _ Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel. _ Contact the maintenance personnel.
TROUBLESHOOTING MAINTENANCE 19 TROUBLESHOOTING The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confirmed. PROBLEM CAUSES SOLUTIONS Washing machine fails to operate. ¬ Poor connection to the power supply. ¬ Power failure. ¬ The washer door is not properly closed. ¬ Machine has not been switched on. _ _ _ _ Check connection to the power supply. Check the power supply. Close the washer door properly.
WIRING CIRCUIT WIRING CIRCUIT P11 R PA14 NTC 1 2 1 2 P P12 FUSE P13 J3-5 J3-4 J4-3 J2-1 J2-2 MOTOR J1-6 N G L FA FA1 N FA3 L PCB J4-4 J4-1 MRL MR MRN MRC J3-1 J3-3 J2-9 J2-7 M9 J1-5 M8 J1-7 M10 J1-1 M1 J1-4 J1-2 M5 M3 J1-3 M4 J3-2 M6 J2-4 2 2 2 1 1 EVF EVP PS Motor--------------Motor PCB----------------Printed Circuit Board MR------------------Door Lock R---------------------Heating Element PS-------------------Drainage Pump EVF,EVP-----------Water Inlet Ma