UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 1 Bluetooth® Headset for Mobile Phones ET2000 v1.
UG_et2000_v1.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 1 USER GUIDE Contents Overview ............................................................................................................................ 2 Unpacking ezTalker mini .................................................................................................. 2 Getting to Know ezTalker mini .......................................................................................... 3 Getting Started .............................................
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 2 Overview ezTalker miniTM by Tekkeon is a miniature cord-free headset that enables comfortable, handsfree communication with your Bluetooth® mobile phone. ezTalker mini works with your Bluetooth mobile phone to provide clear, high-quality communication. While using your ezTalker mini headset, you can store your mobile phone in your pocket, backpack, or briefcase—just about anywhere in close proximity that is convenient for you.
UG_et2000_v1.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 4 Charging ezTalker mini Before using ezTalker mini, you must charge the headset for approximately two hours. When fully charged, the battery provides up to five hours of talk time and up to 120 hours of standby time. To Charge the Headset 1. Remove the rubber plug that covers the charging jack on the upper left side of the headset. 2. Plug the power adapter into the charging jack. 3. Plug the power adapter into a wall outlet.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 5 To Pair the Devices 1. Turn on the mobile phone and place it next to the headset. 2. Initiate the Bluetooth device-pairing (discovery) feature on the mobile phone. Refer to the mobile phone user guide for instructions on initiating this feature. 3. With the headset turned off, press and hold the TALK button until the blue and amber LEDs flash alternately or until you hear Pairing tone (approximately five seconds). 4. Release the TALK button.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 6 Fitting ezTalker mini On Your Ear ezTalker mini is designed to fit comfortably in your ear. For added comfort, you can change the ezFit Earpiece. For added stability, you can add the ezEarhook. To Place the Headset On Your Ear 1. Place the ezTalker mini speaker in your ear with the microphone angled toward your mouth. The headset should fit snugly in your ear and remain in your ear when you move your head.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 7 To Remove the ezEarhook 1. Gently pull the ezEarhook away from the headset stem until it separates from the headset. Powering ezTalker mini To Turn On the Headset 1. Press and hold the TALK button until the blue LED flashes or until you hear the On tone (approximately four seconds). The headset turns on and is placed in standby mode, ready to make and receive calls. While the headset is on and in standby mode, the blue LED will flash at two-second intervals.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 8 To Make Calls Using Voice Dialing (if supported by your mobile phone) 1. Press the TALK button on your headset. You will hear two beeps. 2. When prompted by the mobile phone (usually about five seconds), speak the name of the person you wish to call. The call is automatically connected to your headset. TIP: In a noisy environment, you should dial the number from the mobile phone keypad as the loud background noise may interfere with voice commands.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 9 To Answer a Call Waiting Call (if supported by your mobile phone) - 1. When you hear two beeps while connected on a call, press and hold the Volume button until you hear a short beep followed by a long tone (approximately 3 seconds). The original call will be placed on hold and the new call be will be connected. Your phone will display the incoming and connected calls. 2.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 10 Adjusting the Volume The volume can be adjusted using the volume controls on ezTalker mini or your mobile phone. To Increase the Volume 1. Press and release the top VOLUME button +. Figure 4. Volume buttons To Decrease the Volume - 1. Press and release the bottom VOLUME button . Muting ezTalker mini You can mute and un-mute the microphone temporarily so that you cannot be heard by the connected party. To Mute the Headset - 1.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 11 Visual and Audible Indicators Two LEDs (blue and amber) indicate the status of the headset, while tones heard through the headset provide an audible indication of a requested action. Following are descriptions of visual and audible indicators provided by your ezTalker mini headset. Visual Indicators LED Status Indicates Blue LED flashes at two-second intervals Headset is in standby mode, ready to make and receive calls.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 12 Troubleshooting Issue Solution When you initiate the Bluetooth device pairing feature on your mobile phone, your phone cannot find ezTalker mini. Verify that ezTalker mini is placed in Pairing Mode (blue and amber LEDs are flashing alternately). If not, place the headset in Pairing Mode. Your ezTalker mini headset is not communicating with your mobile phone.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 13 Troubleshooting (continued) Issue Solution Even though your headset is turned on, the call is not automatically connected to ezTalker mini when you dial a number on your mobile phone. 1.Ensure that your Bluetooth mobile phone is set to Bluetooth mode, and that ezTalker mini (BTHS) has been selected as the connected Bluetooth device. (This is important as most Bluetooth phones are designed to pair with more than one Bluetooth device.) 2.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 14 Disclaimer of Warranties Any user of this product does so at the user’s own risk. To the maximum extent permitted by applicable law, Tekkeon, Inc.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 15 FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
UG_et2000_v1.
UG_et2000_v1.
UG_et2000_v1.2_r1 10/21/05 11:05 AM Page 18 www.tekkeon.com © 2004, 2005 Tekkeon, Inc. All Rights Reserved Rev.