TKR6500 EB410 Buggy Manual REV2

Vehicle
(2 cell)
(50-80 ft Straight)
Small Track
(pinion/spur)
Large Track
(pinion/spur)
(80-150 ft Straight)
EB410
Motor
5.5T
6.5T
7.5T
8.5T
10.5T
18/81 tooth
19/81 tooth
20/81 tooth
20/76 or 21/81
21/76 or 22/81
19/81 tooth
20/81 tooth
21/81 tooth
21/76 or 22/81
22/76 or 23/81
13.5T
25/70 tooth 26/70 tooth
TKRBB040725 – Ball Bearings (4x7x2.5mm,
sold in pack of 4pcs) Bearings for the
bellcrank/ackerman plate. 8pcs required in kit.
TKRBB05114 – Ball Bearings (5x11x4, 4pcs)
Di pinion support bearings for the front/rear
transmission housings. 4pcs required in kit.
TKRBB10154 – Ball Bearings (10x15x4mm,
sold in pack of 4pcs) Bearings for all three dis.
Also inner front steering blocks/rear hub carriers.
10pcs required in kit.
TKRBB06124 – Ball Bearings (6x12x4mm, 4pcs)
Bearings for outside of steering blocks and outer
rear hub carriers. 4pcs required in kit.
PART
#
/COLOR F / R
Rear
Rear
Rear
Front
Front
Front
Front
Rear
Rear
1.2
1.2
7.75
7.38
53mm
53mm
2.82
3.02
Front
TKR6796
TKR6797
TKR6793
TKR6794
TKR6795
TKR6784
TKR6785
TKR6786
TKR6787
TKR6783
WIRE DIA.
1.2
1.2
1.2
1.3
1.3
1.3
1.3
1.3
COILS
9.38
8.75
8.25
9.0
8.5
8.13
7.75
9.5
LENGTH
53mm
53mm
53mm
45mm
45mm
45mm
45mm
45mm
LENGTH
COILS
WIRE DIA.
2.20
2.41
2.60
3.16
3.41
3.62
3.85
2.95
RATE
Changes to wheelbase can aect the overall handling of your vehicle, since it adjusts the distribution
of weight on the wheels as well as the angle of the driveshafts. Shortening the wheelbase at the
rear will give you more steering into a turn and o power, less steering out of a turn and on power.
Lengthening the wheelbase at the rear will yield the opposite results.
Shortening the wheelbase in the front will land jumps a little better and lengthening it will be better
through small bumps. In general a longer wheelbase is better on open and/or bumpy tracks and a
shorter wheelbase is better on tighter technical tracks.
This chart shows the recommended starting ratios for the
common motor winds. Please consult the motor/esc manu-
facturers recommended settings to ensure you start with the
best final drive ratio (FDR) for your equipment. When setting
your mesh you want to be able to slightly rock the spur gear
back and forth without moving the pinion gear. Tekno RC is
not responsible for damage done to your electronic equipment
or gears due to improper gearing or mesh.
* For bearing maintenance, please refer to page 28.
Softer springs will increase traction through the turns by allowing
more roll, slow down the responsiveness of the vehicle, and can
be better in the bumps. Stier springs will increase corner speed
if traction is available and will also tend to jump and land better.
Once you find a set of springs you like you will typically only
change them for tracks with dramatically dierent conditions.
Sway bars are used to adjust a
vehicle's lateral grip by resisting
chassis roll. A thicker bar
decreases roll more than a
thinner bar will. More roll means
more grip and less roll means
less grip. The front sway bar
aects mainly o-power
steering at corner entry. The
rear sway bar aects mainly
on-power steering and stability
in mid-corner and at corner exit.
Pistons with smaller holes work well for smoother tracks with large jumps and pistons with larger holes work
well for rougher tracks with less jumps. Smaller hole pistons will typically use thinner oil than larger hole
pistons. Shock oil is also aected by the ambient temperature so a change in viscosity might be necessary
with a change of 5°C or ~10°F.
Front Arm
Rear Arm
Wheelbase Adjustments
FORWARD
BACKWARD
FORWARD
BACKWARD
Front: Changing front di oil aects overall steering response. Thinner can increase o-power steering but
the vehicle may be twitchy and harder to drive. Thicker can increase on power steering and stability. We
recommend 10k to 20k in the front di.
Center: Changing center di oil aects the front-to-rear drive balance. Thicker will reduce o-power
steering and on-power rear traction but increases on-power steering and acceleration if traction is available.
Thinner will increase o-power steering and on-power rear traction but reduce on-power steering and
acceleration. We recommend 10k to 30k in the center di.
Rear: Thinner rear di oil increases o-power steering and reduces traction into a corner. It also reduces
on-power steering and increases traction out of a corner. Going too thin will make your vehicle inconsistent,
however. Thicker rear oil will have opposite eects, and once again, going too thick will make the vehicle
inconsistent. We recommend 5k to 10k in the rear di.
Dierentials
Springs
Pistons
Sway Bars Bearing Chart
Gearing Recommendations
27
Set Up Information
(continued)