P H A S E R 7 5 0 COLOR PRINTER ® User Guide ® www.tek.
Phaser® 750 Color Printer User Guide 071-0632-00 December 1999
Copyright © Tektronix, Inc. Unpublished rights reserved under the copyright laws of the United States. Contents of this publication may not be reproduced in any form without permission of Tektronix, Inc. Tektronix®, Phaser®, PhaserShare®, ColorStix®, the TekColor® icon, and Made For Each Other® are registered trademarks of Tektronix, Inc. PhaserLink™, PhaserPort™, PhaserPrint™, PhaserSym™, PhaserTools™, TekSMART™, and the TekColor™ name are trademarks of Tektronix, Inc.
PANTONE® Colors generated by the Phaser 750 Color Printer are four- and/or three-color process simulations and may not match PANTONE-identified solid color standards. Use current PANTONE Color Reference Manuals for accurate colors. PANTONE Color simulations are only obtainable on this product when driven by qualified Pantone-licensed software packages. Contact Pantone, Inc. for a current list of qualified licensees. All trademarks noted herein are either the property of Tektronix, Inc., Pantone, Inc.
Warranty Printer Warranty Tektronix warrants that the Phaser 750 Printer will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment.
Consumables Warranty Tektronix warrants that the Customer Replaceable Consumables (CRCs) will be free from defects in materials and workmanship for a period of ninety (90) days (six (6) months where longer periods are required by law) from the date of installation, but not more than one (1) year from date of shipment. Under this warranty, the Customer must notify Tektronix or its authorized service representative of the defect before the expiration of the warranty period.
For the software warranty please see the end user license agreement included with the software. If you are an Australian consumer, you should be aware that the Trade Practices Act 1974 and equivalent State and Territory legislation (collectively "the Acts") contain special provisions designed to protect Australian consumers.
User safety summary Terms in manual: Caution: Conditions that can result in damage to the product. Warning: Conditions that can result in personal injury or loss of life. Use proper power source: Do not operate this product from a power source that applies more than the voltage specified. To avoid fire hazard, use only the power cord specified for this product.
Symbols as marked on product: DANGER high voltage: Protective ground (earth) terminal: Hot surface on or in the printer. Use caution to avoid personal injury: Use caution. Refer to the manual(s) for information: Warning If the product loses the ground connection, usage of knobs and controls (and other conductive parts) can cause an electrical shock. Electrical product may be hazardous if misused. Warning For your protection, do not defeat any interlocks.
Contents Tektronix Supplies and Accessories Print Quality Modes 8 TekColor™ Color Corrections Paper Tips 1 9 10 Paper and Transparency Trays Multi-Purpose Tray 13 17 Loading Special Media 23 Automatic 2-Sided Printing 31 Manual 2-Sided Printing From the Multi-Purpose Tray Troubleshooting Print Quality Media Jams Getting Help 38 47 58 Controlling Color Density User Guide 35 61 ix
x Phaser 750 Color Printer
Tektronix Supplies and Accessories Front Panel Display Toner Cartridges Supplies Imaging Unit & Main Charge Grid Front Door Toner Door Fuser & Fuser Roll 0632-61 Note Inside the printer, all handles, knobs, and other features that the user interacts with are blue. When the front panel prompts you that a supply is low or needs to be replaced, make sure that you have replacements on hand. To order supplies and accessories, contact your local dealer or visit the Tektronix web site: www.tek.
Supplies 33100-33 High Capacity Toner Cartridges Item Part Number Cyan 016-1800-00 Magenta 016-1801-00 Yellow 016-1802-00 Black 016-1803-01 Standard Toner Cartridges Item Part Number Cyan 016-1804-00 Magenta 016-1805-00 Yellow 016-1806-00 Black 016-1807-01 0236-44 Main Change Grid Item Part Number Main Charge Grid 016-1665-00 2 Phaser 750 Color Printer
33100-35 Fuser Item Part Number 110 volt 016-1839-00 220 volt 016-1840-00 33100-36 Fuser Roll and Cleaning Pad Item Part Number Fuser Roll (with Cleaning Pad) 016-1843-00 Fuser Cleaning Pad 116-0329-00 User Guide 3
0236-41 Imaging Unit Item Part Number Imaging Unit (Color Imaging Kit) 016-1841-00 0236-43 Transfer Kit Item Part Number Transfer Kit 016-1842-00 4 Phaser 750 Color Printer
Tektronix Professional Printing Paper Item Size Description Part Number Premium Color Printing Paper A/Letter (U. S.) 8.5 x 11 in. 500 sheets 016-1368-00 Premium Color Printing Paper A4 (Metric Letter) 500 sheets 210 x 297 mm 016-1369-00 Glossy Coated Paper A/Letter (U. S.) 8.5 x 11 in. 100 sheets 016-1704-00 Glossy Coated Paper A4 (Metric Letter) 100 sheets 210 x 297 mm 016-1705-00 Premium Cover Paper A/Letter (U. S.) 8.5 x 11 in.
Tektronix Color Laser Labels Size Description Part Number A4 (Metric Letter) 210 x 297 mm 100 sheets / 14 labels per sheet 016-1688-00 38.1 x 99.1 mm labels A4 (Metric Letter) 210 x 297 mm 100 sheets / 8 labels per sheet 67.7 x 99.1 mm labels 016-1689-00 Paper Trays Item Paper Capacity Part Number A/Letter (U. S.) 250 sheets 436-0282-02 A4 (Metric Letter) 250 sheets 436-0283-02 U. S. Legal 250 sheets 436-0314-02 Transparency Trays Item Part Number A/Letter (U. S.
Automatic Duplex/Lower Tray Assembly Features ■ Automatic duplex with the Duplex Unit ■ Lower Tray Assembly with: ■ 1 Paper Tray ■ 1 Transparency Tray ■ Increased paper-printing capacity ■ Increased printing versatility and convenience. Part Number U.S.
Print Quality Modes You can select the Print Quality mode in the follow ways: 1. From the software driver. (This always overrides the front panel setting.) 2. From the printer’s front panel. Press Menu, scroll to Print Quality, press Menu, and select a Print Quality Mode. Black and White Converts all colors to black, white, and shades of gray. Prints at 1200 x 600 dpi. Fast Color Fastest color print mode.
TekColor™ Color Corrections You can select the TekColor™ Color Correction mode in the following ways: 1. From the software driver. (This always overrides the front panel setting.) 2. From the printer’s front panel. Press Menu, scroll to Print Quality, press Menu, and select a TekColor™ Color Correction. Automatic Optimizes colors for each element (text and graphics) on the page. Best all-purpose selection. None No color correction applied. Use with printer specific (i.e.
Paper Tips Caution Do not use any media designed for inkjet printers, especially inkjet coated paper and inkjet transparencies. Inkjet media is coated with a substance that will damage the fuser. Tektronix does not furnish warranty service for damage or malfunction caused by the use of non-Tektronix supplies or consumables. Always use Tektronix media that has been specially designed for use with Tektronix Laser Printers.
■ When you select a media tray by location (Upper, Middle, Lower, Multi-Purpose Tray), the printer picks from that tray, regardless of the tray’s media type or size. ■ Always keep media in a sealed package to avoid the effects of humidity, which can affect print quality. Letterhead ■ For printing letterhead: ■ In the PAPER tray put this material face-down. ■ In the Multi-Purpose Tray put this material face-up.
Supported page sizes and image area The printer supports five media sizes, which you select in the Print screen (using a supported printer driver). Margins Media Page size Print area Top / Bottom Sides 1 Letter 8.5 x 11 in. 8.21 x 10.56 in. .22 in. .14 in. 2 A4 210 x 297 mm 200 x 287 mm 5 mm 4.8 mm 3 Legal 8.5 x 14 in. 8.2 x 13.5 in. .23 in. .14 in. 4 Executive 7.25 x 10.5 in. 6.93 x 10.31 in. .22 in. .15 in. 5 #10 Envelope 4.13 x 9.5 in. (104.8 x 241.3 mm) 3.8 x 9.2 in. (96.
Paper and Transparency Trays Paper Tray R PE PA A4 PAPER A/Letter PAPER A4 PAPER Legal 0632-01 ■ 250-sheet capacity ■ 60 - 90 g/m2 (16 - 24 lb.) ■ Use Tektronix Premium Color Printing Paper or Premium Laser Bond Paper for best results. ■ Paper only. Do not load transparencies. Note Do not use transparency in the PAPER tray. This will result in a Jam-Wrong Media error. User Guide 13 Trays Load only laser paper in the paper trays.
Transparency Tray CY EN AR SP AN A4 TR TRANSPARENCY A/Letter TRANSPARENCY A4 0632-02 ■ Use only Tektronix transparencies. See page 1 for supplies ordering information. For information on Tektronix transparencies, visit the Tektronix web site: www.tek.com/Color_Printers/products/supplies/trans/index.html ■ Install the transparency tray only in the printer’s upper or middle tray slots. If this tray is installed in the lower tray slot, a front panel error occurs that stops the print job.
Loading Paper or Transparency Tray Note Place the side to be printed (for example, letterhead paper) face-down under the hooks. 1. Push down on the tray’s metal plate until it clicks, locking it in place. R PE PA A4 0632-08 2. Fan the media to release sheets that are stuck together.
3. Place the media in the tray under the hooks. Caution Keep the media level below the indicator on the tray’s label; otherwise, the printer may jam or be damaged. ■ Letterhead: Load this material face-down under the tray hooks. ■ Transparencies: Place the Tektronix logo strip face-up under the transparency tray hooks. Use Tektronix transparencies only. MAXIMUM TRAY LEVEL CY EN AR SPA4 AN TR 0632-10 4. 5. Tray capacity: a. Paper tray 250 sheets b.
Multi-Purpose Tray Always use the Multi-Purpose Tray for speciality media; it supports the following media types: Supported Media Tray capacity Media thickness switch Paper and Paper 2nd Side 75-105 g/m2, (20-28 lb.
Note Multi-Purpose Tray For the best coverage when using laser paper heavier than 105 g/m2 (28 lb.) in the Multi-Purpose Tray, select Heavy Paper as the media type. If the printer experiences frequent media jams at the Multi-Purpose Tray, move the Media Thickness Switch to a thicker setting. If the printer experiences frequent double-feed errors at the Multi-Purpose Tray, move the Media Thickness Switch to a thinner setting.
Loading the Multi-Purpose Tray 1. Pull out the slide and adjust the guides for the width of the media. 0632-11 2. Adjust the Media Thickness switch for the media you are using (see page 17).
3. Insert the media: ■ For Tektronix Transparencies place the Tektronix strip facing down and refer to page 23. ■ For Tektronix Color Laser Labels, place face-up and refer to page 28. ■ For envelopes, place face-up and refer to page 25. ■ For letterhead, place face-up and refer to page 11. 0632-63 4.
Tektronix Glossy Coated Paper Tek Glossy Coated Paper OK Letter or A4 OK 0632-45 Tektronix Premium Cover Paper Heavy Paper OK Letter or A4 OK 0632-64 Tektronix Color Laser Label Tek Labels OK Letter or A4 OK 0632-47 Paper ■ Letterhead ■ Office Laser Paper ■ Standard paper and letterhead 75 - 105 g/m2 (20 - 28 lb.
Paper 2nd Side ■ Standard paper and letterhead 75 - 105 g/m2 (20 - 28 lb.) Paper-2nd Side OK Letter OK Legal, A4, or Executive 0632-49 Heavy Paper ■ Cover Stock 120-163 g/m2 (60 lb.) ■ Index Stock 120-163 g/m2 (90 lb.) ■ Card Stock 120-163 g/m2 (40 lb.) Heavy Paper OK Letter OK Legal, A4, or Executive 0632-50 Envelope #10 Envelope OK # 10 OK 0632-51 5. 22 In the Print screen (using a supported driver), select Multi-Purpose Tray. Send the job to the printer.
Loading Special Media Tektronix Transparencies 1. Set the Media Thickness Switch to Normal. Thin Normal Thick 33100-68 Adjust the tray’s guides for the width of your Tektronix Transparencies. 3. Insert the transparency with the logo strip face-down, entering the printer first. Special Media 2.
4. Fill the Multi-Purpose Tray to the level indicator on the guide (maximum capacity is 50 sheets). 4 3 Special Media 0236-13 5. At the front panel’s media type prompt, scroll to Tek Transparency and press OK. Scroll to the media size Letter or A4. Tek Transparency OK Letter or A4 OK 0632-44 6. 24 In the application’s Print screen under Tray Selection or Paper Source, depending on the driver, select the Multi-Purpose Tray and send the job to the printer.
Printing #10 Envelopes 1. Prepare each envelope: tuck in the envelope flap. 0632-22 2. Adjust the printer’s media thickness switch to Thick. Thin Thick Normal 33100-69 Adjust the printer’s media guides for the width of your envelopes. P St lac H am e er p e P St lac H am e er p e 3. Envelopes 0632-24 4. Insert the envelopes (maximum capacity is 10): a. Short end enters first.
5. b. Side to be printed is face-up. c. The edge where you place the stamp enters the printer first in some applications; make a test print before proceeding. At the front panel prompt, scroll to Envelope then scroll to #10 and press OK. Envelope OK # 10 OK 0632-51 6. 7. 8. In your application create a document with these measurements: ■ Width: (104.1 mm), 4.13 in. ■ Length: (241.3 mm), 9.5 in. ■ Margins: (5 mm), 0.2 in.
Guidelines for envelope printing: Caution Never use envelopes with windows or metal clasps; they will damage the printer. Use envelopes that are at least #10-size. (4.13 x 9.5 in. /104.8 x 241.3 mm) ■ Do not print on the envelope’s back side. ■ Keep unused envelopes in their packaging to avoid the effects of moisture and dryness, which can affect print quality and cause wrinkling. ■ Many applications include a tool for creating an envelope document.
Printing on Tektronix Color Laser Labels At the printer: 1. Adjust the printer’s media thickness switch to Thick. Thin Normal Thick 33100-69 2. Insert the label sheets (maximum capacity is 30 sheets): a. Side to be printed is face-up. b. The top of the sheet enters the printer first.
3. At the front panel prompt, scroll to Tek Labels and press OK, then scroll to the media size Letter or A4. Tek Labels OK Labels Letter or A4 OK 0632-47 In the application: Note For printing Tektronix Color Laser Labels, you can use common software settings. 4. If your application has a setting for Avery® labels, use it as a template. Otherwise, refer to the instructions included with the labels for margin settings. Use the Avery template for the Tektronix labels.
Labels Guidelines for printing on labels: ■ Use Tektronix Color Laser Labels. 30 ■ If any of the labels on a sheet are missing, do not use that sheet; it may damage printer components. ■ When selecting Tek Label as the media type, the printer requires that room temperature be cooler than 27 degrees C (81 degrees F). If the temperature is above this, the printer reports an error and stops printing.
Automatic 2-Sided Printing Caution Never put media in the Duplex Unit; the printer reports a media jam. Use only laser bond paper for automatic two-sided printing in the paper tray. Do not use any special media (glossy coated paper) to print automatic two-sided printing. Two-sided printing can be done manually; refer to Manual 2-Sided Printing From the Multi-Purpose Tray on page 35. Automatic two-sided printing requires that the Lower Tray Assembly be installed.
b. Place the top of the page under the paper tray’s hooks. This example shows letterhead paper. b 1 2 3 4 5 6 7 a R PE PAA4 0632-28 2-sided Prints 3. Insert the paper tray in the printer’s middle (b) or lower (c) tray slots. Note For best results with two-sided printing, use 90 g/m2 (24 lb.) laser paper. 4. Decide on a binding preference (how the page turns) for Step 5: a. Long-Edge binding or uncheck Bind on top edge.
b. Short-Edge binding or check Bind on top edge. 0632-30 5. In the Print screen, select the 2-Sided Printing option and a binding preference: PC Drivers: Windows 95/ Windows 98 a. From the File menu, select Print. b. Click Properties. c. Click the Setup tab. d. Click Print on 2-Sides option. e. Check or uncheck Bind on top edge. Windows NT4 a. Start/Settings/Printers. b. Right-mouse-button-click on your printer’s icon. c. From the pop-up menu, select Document Defaults. d.
Macintosh Drivers: LaserWriter 8.6 a. From the File menu, select Print. b. From the pull-down menu, choose Layout. c. Select Print on Both Sides. d. Select a binding preference. LaserWriter 8.3.4 6. 34 a. From the File menu, select Print. b. Click the Options button. c. Select 2-Sided Printing. d. Select Short-Edge Binding or Long-Edge Binding. Send the job to the printer.
Manual 2-Sided Printing From the Multi-Purpose Tray Side 1 Caution Use only laser bond paper for the automatic two-sided printing in the paper trays. The Multi-Purpose tray should be used for manual two-sided printing on Tektronix Premium Color Printing Paper, Tektronix Glossy Coated Paper, or Heavy Paper. Two-sided printing on specialty media can shorten component life. For opacity and feed reliability, use laser paper that is 90 g/m2 (24 lb. bond).
2. Insert paper with the side to be printed face-up. This example shows letterhead paper. 1234567 32564-06 3. In the printer’s front panel, select the media type and size at the prompt. Front Panel Media Type Paper ■ Tektronix Glossy Coated Paper ■ Tektronix Glossy Coated Paper Heavy Paper ■ Card stock, 120 - 150 g/m2 (32 - 40 lb.) ■ Cover stock, 120 - 150 g/m2 (40 - 54 lb.) ■ Index stock, 120 - 150 g/m2 (60 - 80 lb.) ■ Standard laser paper, 75-105 g/m2 (20-28 lb.
Side 2 Note For a multi-page document, print even-numbered pages for Side 2. (This selection is application-specific). 1. Insert the paper with the blank side face-up. 1234567 32564-07 2. In the printer’s front panel, select the media type and size at the prompt. 3. In the Print screen (using a supported driver), select Multi-Purpose Tray as the Paper Source or Tray Selection. Send the job to the printer. 4. Remove the printed paper from the output tray.
Troubleshooting Print Quality For detailed troubleshooting information, refer to the printer’s CD-ROM or the Tektronix Color Printer Knowledge Base web site: www2.tek.com/TekSMART/ If you notice a problem with the quality of your prints, the probable solution is replacing one of the supplies. Keep in mind this basic guideline: ■ If the symptom appears in a single color: Replace the Toner Cartridge.
2. From the Help menu, scroll to Supplies Information, press OK and print the Supplies Page. Use it to diagnose and correct problems. The Supplies Page contains useful information, such as the remaining life for supplies.
Symptom: Problem in one color only ■ 1 color has many vertical streaks. 33100-61 ■ 1 color has a light vertical streak. 33100-59 ■ 1 color is light or faded.
Solution: 1. 2. Adjust the color density. a. Press Help, and scroll to Print Quality, press Menu, scroll to Calibrate Colors. Press Menu, scroll to Adjust Each Color. Press Menu. b. Adjust the density of the color that has problems. Replace the Toner Cartridge of the color that has problems.
Symptom: Problem in all four colors ■ Streak through all 4 colors. 33100-57 ■ Spot in the same place on the page in all 4 colors. 33100-56 ■ Random spots appear on every page.
Solution: 1. The choice of media; check the following: a. Use Tektronix media. b. Use the correct media tray for the media you are using. c. When using the Multi-Purpose Tray, select the correct media in the front panel. 2. Run Clean for Smudges. Press Help, scroll to Print Quality. Press Menu, scroll to Clean for Smudges. Press Ok and press Confirm. 3. Print about 25 blank pages until the problem disappears. 4. Replace Imaging Unit, or Fuser, or Fuser Roll.
Symptom: All four colors are solid black Prints are black (edge to edge). 33100-54 Solution: Remove then re-insert the Main Charge Grid. If problem persists, replace the Main Charge Grid.
Solution: 1. Choice of media; check the following: ■ Use Tektronix media. ■ Use the correct media tray for the media you are using. ■ When using the Multi-Purpose Tray, select the correct media in the front panel. 2. Relative humidity may be too low (below 30 percent relative humidity). ■ Refer to Calibrate for Paper in the printer’s front panel and run this mode: ■ 3. Press Help, scroll to Print Quality, press Menu, scroll to Calibrate for Paper, press Menu, print the references pages.
Symptom: Pieces of print image missing all four colors 1. Pieces of the printed image are missing and reappear out of place, approximately 129 mm (5 in.) down the page. 33100-67 2. Media frequently wraps around the Fuser (Jam at C). Solution: 1. Choice of media; check the following: ■ Use appropriate media in the correct tray location; refer to page 13 through page 28. ■ Print 10-20 blank pages of plain paper.
Media Jams Preventing media jams To reduce the frequency of paper and transparency jams, use Tektronix media and occasionally clean the rollers. From the Help Menu, scroll to Print Quality and press OK. Scroll to the Help Pages and press OK. Scroll to the Paper Tips and print and read the tips to avoid media jams. ■ When using the Multi-Purpose Tray, always set the media thickness switch for the media you are using. See page 17.
Jam at A Solution 1 Jams Open the left side door; remove the jammed media. 33100-08 Solution 2 Remove the media tray; remove the jammed media from inside the printer.
Jam at B (Lower Tray Assembly Only) Solution 1 Open the lower left side door and remove the jammed media. 33100-10 Solution 2 Remove the selected media tray (middle or lower tray) and remove the jammed media from inside the printer.
Jam at C Caution The Fuser is hot. To avoid personal injury, use caution or wait for the Fuser to cool before touching it. 1. Remove the Fuser: a. Open the printer’s front door. b. To unlock the Fuser, turn the small blue thumbscrew counterclockwise. c. At the lower left side of the Fuser, press the safety catch and slide the Fuser out of the printer. a b c 0632-31 2. Remove the Fuser Roll: a. To unlock the Fuser Roll, press out on the two tabs. b.
3. To release the jammed media, turn the Fuser’s large blue knob clockwise or counterclockwise. 0632-33 4. Remove the jammed media from the Fuser. 0632-34 5. Re-insert the Fuser Roll into the Fuser; re-install the Fuser. 6. The printer automatically prints five blank pages which cleans the fuser and then resumes the current print job.
Jam at D Caution The Fuser is hot. To avoid personal injury, use caution or wait for it to cool before touching it. Solution 1 1. Open the front door. 2. Pull open the access door; the media is visible. 3. Turn the Fuser’s large blue knob counterclockwise. 4. Remove the media. 3 4 2 r ette r pe A/L Pa 0632-53 Caution If the Fuser knob does not turn, do not force it or you may damage the Fuser. Instead, remove the Fuser and Fuser Roll; then turn the Fuser knob to release the jammed media. .
Solution 2 1. Open the front door and the right side door. 0632-35 2. Turn the Fuser’s large blue knob counterclockwise. 3. Remove the jammed media.
Jam at E Solution 1 Remove the jammed media from the output tray. r tte Le er A/Pap 33100-15 Solution 2 Pull open the access door (above the plastic output tray) and remove the media. r tte Le er A/Pap 33100-16 Note Open and close the printer’s front door to clear the error message.
Jam at Multi-Purpose Tray 33100-17 1. Remove all media in the Multi-Purpose Tray. 2. Remove the jammed media from the Multi-Purpose Tray. 3. Set the Media Thickness switch for the media you are using (page 17). 4. Re-insert the media in the Multi-Purpose Tray. Note To clear the error message, open and close the printer’s front door.
Jam at Duplex Unit 1. Remove the Duplex Unit (it is in the printer’s upper slot). 0632-37 2. Open the Duplex Unit. 0632-38 Note If paper is not in the Duplex Unit, open the right side door; paper may be jammed there.
3. Remove the jammed media. 0632-39 4. Close the Duplex Unit; press down to make sure that it snaps shut on both sides. 0632-40 5. Re-insert the Duplex Unit into the printer’s upper slot.
Getting Help Getting Help gives you a comprehensive set of instructions to solve printer problems. The printer's auto-running CD-ROM guides you to the various resources available for installing and learning more about your Tektronix color printer. Use the CD-ROM to install your printer driver software, view and print user documentation, and watch how-to videos.
Tektronix web site www.tek.com/Color_Printers/ ■ Product and supplies information ■ Downloading printer drivers ■ Finding your local reseller ■ Online documentation TekSMART™ Knowledge Base www2.tek.com/TekSMART/ Is the same troubleshooting knowledge base used by Tektronix Customer Support staff ■ Application issues ■ Networking issues ■ Printer errors ■ Print-quality issues ■ Troubleshooting Getting Help ■ PhaserLink™ Software www.tek.com/Color_Printers/products/phaserlink.
Color Connection www.colorconnection.tektronix.com Color resource for tools and information to help you get the most out of your color printer: ■ Interactive tutorials and helpful tips for using your printer and favorite software applications ■ Easy access to online technical support. ■ Customized features to meet your individual needs Getting Help Other online services Anonymous ftp server: ftp.tek.com/Color_Printers/ Subscribe to email update notices: www.colorconnection.tektronix.com U. S.
Controlling Color Density When colors look faded, adjust the toner color density to extend the life of the components. Print and use the Color Reference Page 1. In the printer’s front panel, press Help scroll to Print Quality. Press Menu, scroll to Calibrate Colors. Press Menu, scroll to Adjust Each Color. Press Menu, and print the Color Reference Page. 2. Compare the Color Reference Page to the Color Density Samples.
Color Density 62 Phaser 750 Color Printer
® Printed on recycled paper 0 7 1 - 0 6 3 2 - 0 0