User Manual
Table Of Contents
- toc
- Important safety information
- Compliance information
- Preface
- Installation
- Before Installation
- Operating Considerations
- Connecting Probes
- Securing the Oscilloscope
- Powering on the Oscilloscope
- Powering off the Oscilloscope
- Functional Check
- Compensating a TPP0250, TPP0500B or TPP1000 Passive Voltage Prob
- Compensating a non-TPP0250, non-TPP0500B or non-TPP1000 Passive
- Application Module Free Trial
- Installing an Application Module
- Upgrading Bandwidth
- Changing the Language of the User Interface or Keyboard
- Changing the Date and Time
- Signal Path Compensation
- Upgrading Firmware
- Connecting Your Oscilloscope to a Computer
- Connecting a USB Keyboard to Your Oscilloscope
- Get Acquainted with the Instrument
- Acquire the Signal
- Setting Up Analog Channels
- Using the Default Setup
- Using Autoset
- Acquisition Concepts
- Using FastAcq
- How the Analog Acquisition Modes Work
- Changing the Acquisition Mode, Record Length, and Delay Time
- Using Roll Mode
- Act on Event
- Setting Up a Serial or Parallel Bus
- Setting Up Digital Channels
- When and Why to Turn On MagniVu
- Using MagniVu
- Setting Up the RF Inputs
- Trigger Setup
- Display Waveform or Trace Data
- Adding and Removing a Waveform
- Setting the Display Style and Persistence
- Setting Waveform Intensity
- Scaling and Positioning a Waveform
- Setting Input Parameters
- Positioning and Labeling Bus Signals
- Positioning, Scaling, and Grouping Digital Channels
- Viewing Digital Channels
- Annotating the Screen
- Viewing the Trigger Frequency
- Displaying the Frequency Domain Menu
- Analyze Waveform or Trace Data
- Using Markers in the Frequency Domain
- Taking Automatic Measurements in the Time Domain
- Selecting Automatic Measurements in the Time Domain
- Customizing an Automatic Measurement in the Time Domain
- Taking Automatic Measurements in the Frequency Domain
- Taking Digital Voltmeter Measurements
- Taking Manual Measurements with Cursors
- Setting Up a Histogram
- Using Math Waveforms
- Using FFT
- Using Advanced Math
- Using Spectrum Math
- Using Reference Waveforms and Traces
- Using Wave Inspector to Manage Long Record Length Waveforms
- Auto-magnify
- Limit and Mask Testing
- Making Video Tests
- Making Automated Power Measurements
- Save and Recall Information
- Use the Arbitrary Function Generator
- Use the Application Modules
- Appendix A: Warranted Specifications
- Appendix B: TPP0250, TPP0500B and TPP1000: 250€MHz, 500€MHz and
- Appendix C: P6316 General-Purpose Logic Probe Information
- Appendix D: OpenSSL License
Trigger Setup
Push Number of Bytes and enter the number of bytes with Multipurpose a.
Push Addressing Mode on the side menu and select 7-bit or 10–bit. Push Data on the side menu. Enter the data
parameters of
interest with the Multipurp ose a and Multipurpose b knobs.
For more infor
mation on the I
2
C address formats, refer to item 2 under Setting Up Bus Parameters.
SPI Bus Tr igger
You can trigger on SS Active, MOSI, MISO,orMOSI & M ISO.
If you are setting up an SPI trigger and have made a Trigger On selection of MOSI or MISO, push Data on the lower
menu, push MOSI or MISO on the side menu, and enter the data parameters of interest using the Multipurpose a and
Multipurpose b knobs.
Then push Number of Bytes and enter the number of bytes with the Multipurpo se a knob.
If you s elect MOSI & MISO, push Data on the lower menu and enter the parameters of interest in the side menus.
RS-232 Bus Trigger
You can tr
igger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx End of Packet, Tx Data,orRx Data.
If you ar
e setting up an RS-232 trigger and have made a Trigger On selection of Tx Data or Rx Data, push Data on the
lower menu.
Push Number of Bytes and enter the number of bytes with Multipurpose a.
Push Data on the side menu, and enter the parameters of interest with the Multipurp ose a and Multipurpose b knobs.
CANandCANFDBusTrigger
You can trigger on Start of Frame, Type of Frame, Identifier, Data, Id & Data, End of Frame, Bit Suffing Error, and
Missing Ack, FD BRS Bit, FD ESI Bit, Form Erro r, and Any E rror. FD BRS Bit, FD ESI Bit, Form Error and Any Error are
available only when CAN FD is selected as BUS.
If you are setting up a CAN or CAN FD trigger and have made a Trigger On selection of Type of Frame, push Frame
Type on the lower menu, and select Data Frame, Remote Frame, Error Frame,orOverload Frame. AllCANFDdata
packets register as Data Frame.
If you have made a Trigger On selection of Id entifier, push Identifier on the lower menu and select a Format. T hen push
Identifier on the side menu, and enter a binary or hex value with m ultipurpose knobs a and b.
Push Direction on the lower menu and select the direction of interest: Read, Write,orRead or Write.AllCANFDdata
packets register as Write direction.
If you have made a Trigger On selection of Data, push Data on the lower menu and enter the parameters of interest.
LIN Bus Trigger
You c an trigger on Sync, Identifier, Data, Id & Data, Wakeup Frame, Sleep Frame,orError.
If you are setting up an LIN trigger and have made a Trigger On selection of Identifier, Data,orIdentifier & D ata, push
I
dentifier or Data on the lower menu and enter the parameters of interest on the resulting side menu.
MDO3000 Series Oscilloscopes User Manual 97