Tele Radio Jaguar MANUAL Rev.
CONTENTS
TELE RADIO SETTINGS DOCUMENT Download for print at: www.tele-radio.
FREQUENCY BANK CHANNEL FREQ.BANK 1 OPTION CHANNEL FREQ.BANK 3 OPTION 1 433.075 111 1 433.125 311 2 433.175 112 2 433.225 312 3 433.275 113 3 433.325 313 433.425 314 4 433.375 114 4 5 433.475 115 5 433.525 315 6 433.575 116 6 433.625 316 7 433.675 117 7 433.725 317 8 433.775 118 8 433.825 318 433.925 321 9 433.875 121 9 10 433.975 122 10 434.025 322 11 434.075 123 11 434.125 323 12 434.175 124 12 434.225 324 434.325 325 13 434.
RECEIVER T70RX-09SB 2 1 3 4 5 6 7 9 8 48-230 VAC 12-24 VAC/DC 1 2 3 4 5 7 6 8 T70RX-15SB 3 4 5 6 RELAY 1 7 9 8 RELAY 2 RELAY 3 RELAY 4 RELAY 5 RELAY 6 RELAY 7 RELAY 8 RELAY 9 48-230 VAC 12-24 VAC/DC 1 10 2 11 3 12 4 13 5 the yellow power supply LED the red CODE STORING LED the yellow LATCH LED the green INTERLOCKING LED LOGOUT LED Receiver switch Antenna connector FUNCTION button SELECT button 9 2 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 14 6 7 15 8 9 1. 2. 3. 4. 5. 6. 7. 8. 9.
TRANSMITTER 1. 2. ON OFF 7 T70TX-06TTB 1. red LED 2. ON button 3. OFF button 1 2 3 4 5 6 7 8 START START T70TX-08ERB 1. rubber cover 2. STOP button 3. yellow LED1 4. red/ green LED 5. yellow LED 2 6. button 7- START button 7. button 8- START button 3. 4. 5. 6. 7.
1. GET STARTED READ THE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING, INSTALLING, PROGRAMMING AND USING TELE RADIO PRODUCTS. Tele Radio cannot be held responsible for any damage or other fault caused by a failure to follow the instructions. Doing so may invalidate the warranty. IT IS YOUR RESPONSIBILITY TO FIND OUT ABOUT THE LAWS AND REGULATIONS THAT APPLY IN YOUR COUNTRY/REGION! 1.2 SAFETY INSTRUCTIONS s s s s s s s s s s This product should only be installed by qualified personnel.
1.3 TECHNICAL DATA THE SYSTEM OPERATING FREQUENCY: CHANNEL: CHANNEL SEPARATION: 433.075-434.650 MHz. 64 (divided into 4 banks) 25 kHz. RECEIVER T70RX-09SB T70RX-15SB WEIGHT: 9 relays 15 relays (with expansion board) 700 grams (15 relays) TRANSMITTER T70TX-08ERB SIZE: WEIGHT: 95 x 185 mm. (incl. rubber cover) 300 grams (incl. batteries) 7 TRANSMITTER T70TX-06TTB SIZE: WEIGHT: 113 x 66 x 35 mm. 120 grams (incl. batteries) ON 1.
1.5 CHECK THE CONTENTS Check that you have got the product that you ordered. If anything is missing, please contact your dealer immediately. The delivery also contains: s 3 alkaline batteries for the transmitter s 1 connection comb s 1 installation and programming instruction manual 1.6 CONNECT THE RECEIVER s s Check that you have connected the power supply to the correct connection terminal.
1.8 INSTALL BATTERIES IN THE TRANSMITTER 1.8.1 On the T70TX-06TTB transmitter 1. 2. 3. 4. 5. Remove the clip. Remove the battery cover. Put the batteries in. Put back the battery cover (2 screws). Put back the clip (2 screws). For optimum performance, use alkaline batteries. NOTE! If you need to change the frequency bank, we recommend doing this before putting back the battery cover and clip. 1.8.2 On the T70TX-08ERB transmitter ID code 1. 2. 3. Remove the battery cover. Put the batteries in.
2 TRANSMITTER SETTINGS 2.1 Starting/ turning the transmitter off 2.1.1 Starting T70TX-06TTB ON 1. Press the ON button for at least 1 second. When the transmitter is active, the transmitter LED flashes red.When transmitting, the transmitter LED lights red continuously. 2.1.2 Turning off T70TX-06TTB 1. Press the OFF button. OFF The transmitter LED goes out. 2.1.3 Starting T70TX-08ERB 1. Pull out the STOP button. 7 2. Press the START buttons 7 and 8 for at least 1 second.
2.2 AUTOMATIC SHUTDOWN SETTINGS 2.2.1 T70TX-06TTB transmitter The transmitter will turn off after1 minute idle. This cannot be adjusted. 2.2.2 T70TX-08ERB transmitter Automatic shutdown means that the transmitter will switch itself off, if you do not press a button for 1 minute (you can adjust this time according to the table below). The transmitter does not log off from the receiver when it is automatically shut down. 2.2.
4. Enter the security code 1, 2, 3, 4 (up to 4 seconds between each number). 2 1 3 7 7 4 7 7 The transmitter LED starts to flash green and yellow transmitter LED 2 goes out. 5. Enter your choice 1-5: ______________________ 1= no automatic shutdown 2= 1 minute 3= 3 minutes 4= 6 minutes 5= 12 minutes Yellow transmitter LED 1 flashes 3 times when the time setting has been changed. 0 min. 1 min. 3 min. 6 min. 12 min. 7 6.
2.3 FREQUENCY SETTINGS If your product will be used in an area with very little risk of interference from other radio-controlled equipment, skip this section. If necessary, you can switch the frequency at a later date. (See the first pages of the manual for frequency table). 2.3.1 Switch frequency bank on T70TX-06TTB NOTE! IF YOU NEED TO SWITCH FREQUENCY BANK, WE RECOMMEND DOING THIS BEFORE REPLACING THE BATTERY COVER AND CLIP. MAKE FREQUENCY BANK SETTINGS BEFORE STORING THE TRANSMITTER IN THE RECEIVER.
2.3.2 Moving up and down within a frequency bank on T70TX-06TTB The user can move up and down within a frequency bank while using the transmitter. This can be useful if there is a major risk of interference within the work area. The default setting is channel 1 in frequency bank 1. The transmitter must be on. 1. Press the OFF button and keep it pressed. OFF 2. Within 3 seconds: Press ON without releasing OFF. ON Transmitter LED flashes for 5 seconds. OFF 3. Release ON and OFF. 4.
2.3.3 Move more than one step on the T70TX-06TTB If you want to move several steps in frequency, you will need to restart the transmitter after every step. In this case you don´t have to wait until the receiver connects to the transmitter. If you move all the way to the bottom of the frequency table, the next step will be back to the top. If you move all the way to the top of the frequency table, the next step will be right at the bottom. 2.
4. Enter the security code 1, 2, 3, 4 (up to 4 seconds between each number). 2 1 3 7 7 The green LED flashes and yellow LED 2 goes out. 5. Press the 3-digit number for OPTION (See the first pages of the manual for frequency table). Yellow transmitter LED 1 flashes 3 times when the setting has been made. 4 7 7 CHANNEL FREQ.BANK 1 OPTION 1 433.075 111 2 433.175 112 3 433.275 113 4 433.375 114 5 433.475 115 6. Make sure to write down the new frequency bank in the Settings document.
2.4.1 Settings to move up and down within a frequency bank on T70TX-08ERB Decide how to move up and down within a frequency bank. Skip this section if you do not want to change the default settings. 1. SAVE NEW FREQUENCY (default setting). When a user moves up or down within a frequency bank, the transmitter saves the new frequency and uses it the next time it is started up. 2.TEMPORARY MOVE When a user moves up or down within a frequency bank, the transmitter will not save the new frequency.
4. Enter the security code 4, 6, 3, 5 (up to 4 seconds between each number). 4 3 5 6 7 7 7 7 The transmitter LED flashes green. Yellow transmitter LED 2 lights up. 5. Enter your choice: 1 2 3 1. SAVE NEW FREQUENCY 2.TEMPORARY MOVE 3. OFF 7 The transmitter turns off. Yellow transmitter LED 2 goes out. 6. Re-start the transmitter by pressing the START buttons 7 and 8 for at least 1 second. 7 8 7 2.4.
2. Release button 7. Keep button 8 pressed. 8 7 1a. Keep button 8 pressed. Press 1 to move DOWN within the frequency. a. 1 Yellow transmitter LED 1 lights up. 1b. Keep button 8 pressed. Press 2 to move UP within the frequency. Yellow transmitter LED 2 lights up. 7 8 b. 2 7 8 NOTE! If you move all the way to the bottom of the frequency table, the next step will be back to the top. If you move all the way to the top of the frequency table, the next step will be right at the bottom. 2.
3. Release button 8. Within 0.3 seconds: Press button 2. 2 Yellow transmitter LED 2 lights up and the transmitter LED flashes green. 7 If you exceed the 0.3 second interval, the transmitter will exit the programming mode and starts up. 4. Enter the security code 3, 4, 4, 3 (up to 4 seconds between each number). 34 3 7 7 43 7 3 7 The green transmitter LED starts to flash.Yellow transmitter LED 2 lights up. 1.
3 RECEIVER SETTINGS 3.1 FUNCTION SELECTION You can make several selections to decide how to use your system. Some of the settings are made on the transmitter, others are made on the receiver.You can see the Function Selections available for your transmitter in this section. This is followed by the selections that you can do on the receiver. Read through the following sections carefully before making the Function Selection choice. 3.1.
2. Release button 7. Keep button 8 pressed. 8 7 3. Release button 8. Within 0.3 seconds: Press 1. 1 Yellow transmitter LED 2 lights up.The transmitter LED flashes green. 7 4. Enter the security code 1,2,3,4 (up to 4 seconds between the numbers). The transmitter LED starts flashing green and yellow transmitter LED 2 goes out. 2 1 3 7 7 4 7 7 1 5. Enter your Function Selection choice: 1 or 2. 7 Yellow transmitter LED 1 flashes 3 times. 2 7 6.
3.2 OPERATING MODE There are two receiver models available (see pictures in the first pages of the manual): s T70RX-09SB- 9 relays s T70RX-15SB- 15 relays (with expansion card) With the T70TX-08ERB transmitter you can choose functionality for the system by choosing one of the preset Operating Modes (see overview on next page). You can change the settings using the receiver switch. STOP button When the transmitter is active and the STOP-button is pressed, all relays go off. 3.2.
OPERATING MODE ON TWORELAYS RECEIVERS BUTTONS OFF 7 LATCHING INTERLOCKING OP. MODE 1 1-2 _ 9 or 15 1-2 No programmable programmable OP. MODE 2 _ 1-3 9 or 15 1-2 Yes programmable programmable OP. MODE 3 _ 1-3 15 2 Yes automatic automatic OP. MODE 4 _ 1-3 15 2 Yes automatic automatic OP. MODE 5 _ 1-3 15 1-2 Yes automatic automatic OP. MODE 6 _ 1-3 15 1-2 Yes automatic automatic OP.
3.3 SELECT OPERATING MODE SELECT OPERATING MODE BEFORE STORING THE TRANSMITTER! 1. Open the receiver (4 screws). 2. Enter the settings on the receiver switch in accordance with the picture shown for each Operating Mode. In some Operating Modes you can decide whether to put the switch in ON or OFF position, depending on what functionality you want for the receiver. A receiver switch that is possible to change is shown in both ON and OFF positions on Receiver switch the picture.
3.3.3 Operating Mode 2 TRANSMITTER: RECEIVERS: NUMBER OF TRANSMITTERS: LATCHING: INTERLOCKING: FUNCT. SELECT 1: FUNCT. SELECT 2: T70TX-08ERB 1-2 receiver(s) with 9/ 15 relays 1-3 Available on relays 4-15 Available on relays 4/5, 6/7, 8/9, 10/11, 12/13 och 14/15. Yes. Transmitter button 8 no function. Yes.Yes. Select Func. Select. 2 on the transmitter. Transmitter button 8 controls 2 receivers via the yellow transmitter LEDs.
3.3.5 Operating Mode 4 TRANSMITTER: RECEIVERS: NUMBER OF TRANSMITTERS: LATCHING: INTERLOCKING: MODE-SPECIFIC: FUNCT. SELECT 1: FUNCT. SELECT 2: T70TX-08ERB 1 receiver with 15 relays 1-3 Available on relays 14 and 15 Automatic on relays 4/5/6, 7/8/9 and 10/11/12 Relay 13 is not used Not possible Yes. Func. Select. 2 must be selected on the transmitter. 4/6 5/6 7/9 8/9 10/12 11/12 TRANSMITTER’S YELLOW LEDS 7 LED 1 activates relay 14 LED 2 LED 1 & 2 relay 15 relays 14+15 3 FUNCT. SELECT.
3.3.7 Operating Mode 6 TRANSMITTER: RECEIVERS: NUMBER OF TRANSMITTERS: LATCHING: INTERLOCKING: FUNCT. SELECT 1: FUNCT. SELECT 2: T70TX-08ERB 1 receiver with 15 relays 1-3 Available on relays 14 and 15 Automatic on relays 4/5/6/7, 8/9/10 and 11/12/13 Not possible Yes. Func. Select. 2 must be selected on the transmitter. Transmitter button 8 controls the receiver via the yellow transmitter LEDs. How the LEDs function depend on how the transmitters are stored (see Storing transmitters section).
3.3.9 Operating Mode 8 TRANSMITTER: RECEIVERS: NUMBER OF TRANSMITTERS: LATCHING: INTERLOCKING: FUNCT. SELECT 1: FUNCT. SELECT 2: T70TX-08ERB 1 receiver with 15 relays 1-3 Not possible Available on relays 4/5/6, 7/8/9, 10/11/12 and 13/14/15 Not possible Yes. Func. Select. 2. must be selected on the transmitter. Transmitter button 8 controls the receiver via the yellow transmitter LEDs. 4/6 5/6 7/9 8/9 10/12 11/12 7 3 FUNCT. SELECT.
3.4 CHANGE OF LED THAT LIGHTS UP DURING STARTUP 3.4.1 On the T70TX-06TTB transmitter The transmitter does not have this option. 3.4.2 On the T70TX-08ERB transmitter Applies to T70TX-08ERB with Function Selection 2. You can select how the yellow LEDs on the transmitter will light up when you start the transmitter. The default setting is for yellow LED 1 to light up when you start the transmitter. If you want to keep the default setting, skip this section. 1. No yellow LED lights up at start 2.
4. Enter the security code 7, 4, 8, 3 (up to 4 seconds between the numbers). 4 7 7 7 3 7 8 7 The green LED starts to flash and yellow LED 2 goes out. 5. Enter your choice: 1. No yellow LED lights up 2. Yellow LED 1 lights up 3. Yellow LED 2 lights up 4. Yellow LEDs 1 + 2 light up 1 2 3 4 7 Yellow LED 1 flashes 3 times. 6. Re-start the transmitter by pressing the START buttons 7 and 8. 7 7 8 3.5 POWER SAVING FOR YELLOW TRANSMITTER LEDS 3.5.
1. Start the transmitter by pressing the START buttons 7 and 8 for at least 1 second. 7 7 8 2. Release button 7. Keep button 8 pressed. 8 7 3. Release button 8. Within 0.3 seconds: Press 1. 1 Yellow LED 2 lights up. The LED starts to flash green. 7 4. Enter the security code 7, 5, 4, 5 (up to 4 seconds between the numbers). 4 5 7 7 7 5 7 7 The green LED starts to flash and yellow LED 2 goes out. 1 7 5. Enter your choice (1 or 2). Yellow LED 1 flashes 3 times.
6. Re-start the transmitter by pressing the START buttons 7 and 8 for at least 1 second. 7 7 8 3.6 LATCHING RELAY FUNCTION In some Operating Modes you can assign a latching function to certain relays (see description of Operating Modes). Latching means that the relay is activated every time a button is pressed, but remains active until the button is pressed again.You can set this on the receiver using the FUNCTION button and the SELECT button. Receiver switch 1.
3.7 INTERLOCKING RELAY FUNCTION In some Operating Modes you can assign an interlocking function to certain relays (see description of Operating Modes). Interlocking means that you can prevent selected relays from activating at the same time, even if the buttons are pressed at the same time, e.g. moving up and down. If two relays are interlocked, nothing will happen if the user presses both buttons at the same time.You can set this on the receiver using the FUNCTION button and the SELECT button.
3.8 STORE THE TRANSMITTER IN THE RECEIVER NOTE! Do not store the transmitter in the receiver until you have selected Operating Mode. Depending on receiver model, you can store 1-3 transmitters. If the maximum number of transmitters has already been stored, all transmitters must be erased before you can store the transmitters that you want. NOTE! If several transmitters are used with one receiver, they must all use the same frequency bank. 1. Start the transmitter that you want to store. ON 7 7 8 1 2.
3. Press the receiver’s SELECT button. All red relay LEDs will light up. The receiver will now start to search for and connect to the transmitter. S F 4. When the transmitter has been stored, the red relay LEDs on the receiver will flash 3 times. 5. Release button 1. 3.9 Erase transmitters F S 1. Press the receiver’s FUNCTION button for more than 0.3 seconds. The red CODE STORING LED on the receiver lights up. 3. Press the SELECT button. S F All the red relay LEDs lights up.
2. Hold down the FUNCTION button and the SELECT button for more than 10 seconds. After 10 seconds, the receiver’s memory has been erased. 3.11 LOGOUT TRANSMITTERS 3.11.1 On the T70TX-06TTB transmitter S F There is no LOGOUT function on this transmitter. 3.11.2 On the T70TX-08ERB transmitter If you want to use more than one stored transmitter with your receiver, you must LOGOUT the transmitter that you used last. LOGOUT 1 There are 3 ways to LOGOUT a transmitter: 1.
LOGOUT 2- only if button 7 is not used for a high-risk function 1. Start the transmitter you want to log out. 2. Press button 7. 7 3. Press the STOP button without releasing button 7. The red transmitter LED lights up for 1 second. Yellow transmitter LED 1 flashes. 7 7 4. The transmitter is now logged out and turns itself off. You can now log on to the receiver using another already stored transmitter. LOGOUT 3- if transmitter can´t be used 1. Press the SELECT button for at least 4 seconds.
EN REPLACE TRANSMITTERS ES On the TX1-C transmitter FR There is no replacing function on this transmitter. On the TX2 transmitter To replace a lost or broken transmitter with a new, without having to use the receiver. Simply use the new transmitter for all button operations. NOTE! The new transmitter must use the same frequency bank as the transmitter that is being replaced. 1. Start the new transmitter. 7 8 7 2. Press the new transmitter´s STOP button. 7 3. The transmitter LED lights red.
THE REMOVABLE RUBBER COVER EN On the TX2 transmitter ES The TX2 transmitter comes with a removable rubber cover that helps prevent the transmitter from bumps, dirt and dust. The rubber cover can be easily removed and wiped off. FR THE RUBBER COVER MUST BE REMOVED TO: 1. Reveal the FCC statements label (see picture below). 2. Reveal the ID code for the product (not the FCC ID code). How to remove the rubber cover 1. Loosen the rubber cover, starting at the top. 2.
EN LOCATE THE IC AND FCC LABELS ES FR 1. Reveal the product information label (see picture). 2. Reveal the FCC and IC label (see picture below). On the TX1-C transmitter 1. Remove the clip (2 screws). 42 FCC ID: ONFT70TX-0XXTB 3. The FCC and IC labels are placed on the inside of the battery compartment. The FCC label is placed on the right side. The IC label is placed on the left side. IC: 4807A-T70TX0XXTB Model No. T70TX-06TTB 2. Remove the battery lid (2 screws) and the batteries.
On the TX2 transmitter EN ES FR FCC ID: ONFT70TX-08ERB 3. The FCC and IC labels are placed on the inside of the battery compartment. The FCC label is placed on the right side. The IC label is placed on the left side. IC: 4807A-T70TX08ERB Model No. T70TX-08ERB 1. Remove the battery lid (2 screws) and the batteries. .
EN IC AND FCC LABELLING TX1-C TX2 GUARANTEE ES Tele Radio’s products are covered by a guarantee against material, construction or manufacturing faults. FR During the guarantee period Tele Radio may replace the product or faulty parts with new ones. Work under warranty must be carried out by Tele Radio or by an authorized service centre specified by Tele Radio. The following faults are not covered by the warranty: s Faults resulting from normal wear and tear. s Parts of a consumable nature.
TELE RADIO AB Sweden, Main office Tel. +46 (0)31-748 54 60 e-mail: info@tele-radio.com www.tele-radio.com TELE RADIO SVERIGE Sweden Tel. +46 (0)31-724 98 00 e-mail: sverige@tele-radio.com TELE RADIO OÜ Estonia Tel. +372 44 511 55 e-mail: m.jyrissoo@tele-radio.com TELE RADIO LTD England Tel. +44 (0) 1625 509125 e-mail: sales@teleradiouk.com TELE RADIO LLC North America & Latin America Tel. +1 (305) 459 0763 e-mail: america@tele-radio.com TELE RADIO ASIA China Tel. +86-(0)592-3111168 e-mail: b.
