Datasheet

ManualsBrandsTELE ManualsMonitoring & Safety Relays2104400

MONITORING RELAY / 1-PHASE CURRENT

V4IM100AL20

Art.Nr.: 2104400

V4IM100AL20P

Art.Nr.: 2104410

Page 1 of 8

TECHNICAL DATA

SUPPLY CIRCUIT

Terminals A1-A2

Supply voltage 24 ... 240 V AC/DC

Supply voltage tolerance

-15 / +10 %

-30 / +30 %

Rated frequency 16,6 ... 400 Hz or DC

Rated frequency tolerance 16,0 ... 420 Hz

Rated consumption

230 V AC

typ. 0,5 W / 0,9 VA

24 V DC

typ. 0,4 W / 0,45 VA

Duty-cycle 100 %

Backup power time < 20 ms

Recovery time > 500 ms

Drop-out voltage ≥ 6 V

MEASURING CIRCUIT

Terminals Built-in current transformer

Measurand current 1-phase

Measuring method True RMS

Monitoring functions undercurrent (U), overcurrent (O), window (W), under- and over-

current with seperate relay outputs (MM); fault latch selectable

(+L)

Measuring range 100 A AC/DC

Frequency

sinus

16,6 ... 400 Hz

non-sinusoidal

values

50 / 60 Hz (arbitrary waveform)

AC/DC current monitoring

Multifunction

Supply voltage 24-240 V AC/DC

Built-in current transformer

2 change-over contacts

Width 45 mm

Control elements

Start-up suppression

Maximum threshold

Minimum threshold

Function selector

Tripping delay

Status indication

LED U/t: Supply voltage

LED Max: Overcurrent

LED Min: Undercurrent

LED Rel1: Relay status Rel1

LED Rel2: Relay status Rel2

http://tele-online.com

VEO

Summary of content (8 pages)

PAGE 1
V4IM100AL20 VEO Art.Nr.: 2104400 V4IM100AL20P Art.Nr.
PAGE 2
V4IM100AL20 VEO Art.Nr.: 2104400 V4IM100AL20P Art.Nr.: 2104410 MONITORING RELAY / 1-PHASE CURRENT MEASURING CIRCUIT Thresholds Max 10 … 100 % Min 5 … 95 % Hysteresis 1% TIMING CIRCUIT Start-up delay fixed ca.
PAGE 3
V4IM100AL20 VEO Art.Nr.: 2104400 V4IM100AL20P Art.Nr.
PAGE 4
V4IM100AL20 VEO Art.Nr.: 2104400 V4IM100AL20P Art.Nr.: 2104410 MONITORING RELAY / 1-PHASE CURRENT GENERAL DATA Stripping length 8 mm Tightening torque max. 1Nm Electrical connection Wire size V4IM...
PAGE 5
VEO MONITORING RELAY / 1-PHASE CURRENT V4IM100AL20 Art.Nr.: 2104400 V4IM100AL20P Art.Nr.: 2104410 FUNCTIONS When the supply voltage U is applied, the output relays Rel1 and Rel2 switch into on-position and the set interval of the start-up suppression (START) begins. Changes of the measured current during this period do not affect the state of the output relays Rel1 and Rel2. Overcurrent monitoring (O) The adjusted maximum threshold IMax must be greater than the adjusted minimum threshold IMin .
PAGE 6
VEO MONITORING RELAY / 1-PHASE CURRENT V4IM100AL20 Art.Nr.: 2104400 V4IM100AL20P Art.Nr.: 2104410 FUNCTIONS Maximum and minimum monitoring (MM) The adjusted maximum threshold IMax must be greater than the adjusted minimum threshold IMin . When the measured current exceeds the adjusted threshold IMax , the set interval of the tripping delay (DELAY) begins. After the interval has expired, the output relay Rel1 switches into off-position.
PAGE 7
V4IM100AL20 VEO Art.Nr.: 2104400 V4IM100AL20P MONITORING RELAY / 1-PHASE CURRENT Art.Nr.: 2104410 CONNECTIONS UN I =/~ I ≤ 100A AC/DC A1 A2 16 18 15 26 28 25 16 18 15 26 28 25 http://tele-online.
PAGE 8
V4IM100AL20 VEO Art.Nr.: 2104400 V4IM100AL20P MONITORING RELAY / 1-PHASE CURRENT Art.Nr.: 2104410 67 mm DIMENSIONS 76 mm 45 mm CONTACT TELE Haase Steuergeräte Ges.m.b.H. Vorarlberger Allee 38 1230 Vienna Austria http://tele-online.com Page 8 of 8 CALL US +43 / 1 / 614 74 - 0 ONLINE SUPPORT info@tele-online.