2102 Wireless Communication Module Installation and Operation Guide Part #60-2003-146 of Assembly #60-2003-145 Copyright © 2003. All rights reserved, Teledyne Isco, Inc.
Foreword This instruction manual is designed to help you gain a thorough understanding of the operation of the equipment. Teledyne Isco recommends that you read this manual completely before placing the equipment in service. Although Teledyne Isco designs reliability into all equipment, there is always the possibility of a malfunction. This manual may help in diagnosing and repairing the malfunction. If the problem persists, call or e-mail the Teledyne Isco Technical Service Department for assistance.
2102 Wireless Communication Module Table of Contents Section 1 Quick Start Guide 1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Wireless Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 Identifying Module Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.2 Communication Connectors . . . . . . . . . . . . . . . . . . . . . . .
2102 Wireless Communication Module Table of Contents List of Figures 1-1 1-2 1-3 1-4 1-5 1-6 1-7 2-1 2-2 3-2 4-1 A-1 2102 Components - Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 2102 Components - Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Upper Connector - Capped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Upper Connector - Uncapped . . . . . . . . . . . . .
2102 Wireless Communication Module Section 1 Quick Start Guide 1.1 Getting Started This Quick Start Guide provides a basic introduction to the 2102 Wireless Communication Module. In this section we discuss: • Identifying key components of the Wireless Module • Module connectors and caps • System connections The intent of this section is only to familiarize you with the basics.
2102 Wireless Communication Module Section 1 Quick Start Guide 1.2 Wireless Module 1.2.1 Identifying Module Components Figures 1-1 and 1-2 identify key components of the 2102. 2 1 3 4 5 Figure 1-1 2102 Components - Top View Table 1-1 Wireless Module Components - Top View Item No.
2102 Wireless Communication Module Section 1 Quick Start Guide 2 1 3 4 Figure 1-2 2102 Components - Bottom View Table 1-2 Wireless Module Components - Bottom View Item No. Description 1 Communication Connector 2 Cap 3 Cap Holder 4 Latch 1.2.2 Communication Connectors When a communication connector is not in use, the connector must always be capped (Figures 1-3 and 1-5). The cap will seal the connector to prevent corrosion, prevent moisture from entering the unit, and improve communications.
2102 Wireless Communication Module Section 1 Quick Start Guide Figure 1-3 Upper Connector - Capped Figure 1-4 Upper Connector - Uncapped Figure 1-5 Lower Connector - Capped Figure 1-6 Lower Connector - Uncapped 1-4
2102 Wireless Communication Module Section 1 Quick Start Guide 1.3 System Connections Connections for the 2102 Wireless modules are described as a base module and remote module. The base wireless module allows a personal computer running Flowlink for Windows (v4.11 or later) to communicate with a remote site that is also using a wireless module. Although base and remote modules function differently, they are identical.
2102 Wireless Communication Module Section 1 Quick Start Guide RS-232 Serial Ports COM1 or COM2 2102 Power Option 1 12 VDC Cigarette Adapter Communication Cable Power Option 2 AC Adapter Base unit cable configurations Power Option 3 2191 Battery Module Note: Always install the Model 2102 ON TOP of the other modules. Interrogator Port 4200 2102 4100/4200/6712 Connect Cable 21xx 2102 2191 Remote unit cable configurations Note: Maximum distance between flow meter and Wireless Module is 50 feet (15.
2102 Wireless Communication Module Section 2 Introduction 2.1 Product Description A 3-module site The 2102 Wireless Communication Module is part of Teledyne Teledyne Isco’s 2100 Series system. The 2100 Series system measures parameters of open channel flow streams. The 2100 Series system is designed to be modular so that you can expand the system to meet your data collection needs.
2102 Wireless Communication Module Section 2 Introduction 2102 Wireless Module Features • No cell phone hassles • no monthly fees • no FCC licensing • no exposed antennas • Long range • Long battery life on two 6-volt alkaline batteries 2.2 Applications Typical applications for the 2102 include: • Sewer Flow • Inflow and Infiltration (I&I) studies • Storm Water Runoff Monitoring • Combined Sewer Overflow (CSO) Monitoring. 2.
2102 Wireless Communication Module Section 2 Introduction 1 Top/Right View 2 3 4 5 2 7 Bottom/Left View 6 Figure 2-1 2102 Controls, Connectors, and Indicators 2-3
2102 Wireless Communication Module Section 2 Introduction 2.4 Technical Specifications This section lists technical information about the 2102 Module. • Table 2-2 lists the technical specifications of the 2102. • Table 2-3 lists the technical specifications of the Spread Spectrum Radio. • Table 2-4 lists the technical specifications of the 2191 Battery Module which must be used with the Model 2102. • Figure 2-2 and Table 2-5 list information about the 2102 Module’s communication connector.
2102 Wireless Communication Module Section 2 Introduction Table 2-3 Technical Specifications – Spread Spectrum Radio Frequency 902 to 928 MHz Transmitter Output Power 1W Typical Range line of sight 0.5 miles (0.
2102 Wireless Communication Module Section 2 Introduction G A F E B D C Communications Port (upper connector shown) Figure 2-2 2102 Connector Pins Table 2-5 Wireless Module Connector Pins Pin 2-6 Name Description A LONA Neuron differential transceiver Data A B LONB Neuron differential transceiver Data B C VIN+ Positive power supply voltage input (+12 VDC nominal) D VIN– Negative power supply voltage input (0 VDC nominal) E RCVUP PC data receiver RS-232 level input F XMTUP PC data
2102 Wireless Communication Module Section 3 Preparation and Installation 3.1 Unpacking Instructions When the Wireless Module arrives, inspect the outside packing for any damage. Then carefully inspect the contents for damage. If there is damage, contact the delivery company and Teledyne Isco (or its agent) immediately. WARNING If there is any evidence that any items may have been damaged in shipping, do not attempt to install the unit. Please contact Teledyne Isco (or its agent) for advice.
2102 Wireless Communication Module Section 3 Preparation and Installation materials that can withstand harsh environments. However, continual exposure to UV light, or periodic submersion should be avoided to extend the life of the components. Communication between the base and remote modules are rated for distances as great as 1/2 mile (800 meters), line of sight. However, obstructions such as buildings and industrial equipment between the modules may reduce the effective distance.
02 Wireless Communication Module Section 3 Preparation and Installation 2. Prepare the Battery Module’s communication connector: a. Inspect the connector. It should be clean and dry. Damaged O-rings must be replaced. Spare O-rings (Teledyne Isco P/N 202-1006-69) are supplied in the maintenance kit (60-2099-001). b. Spray the O-ring’s sealing surface with a silicone lubricant. Note Do not use petroleum-based lubricants. Petroleum-based lubricants will cause the O-ring to swell and eventually deteriorate.
2102 Wireless Communication Module Section 3 Preparation and Installation Note Always install the Wireless Communication Module on top of the other units. 3.3.1 Install the modules The modules should be secured at the site. This prevents damage caused by accidental falls and from being swept away if the channel is flooded. In manholes, the modules are often secured to a ladder rung, or suspended from a spreader bar.
2102 Wireless Communication Module Section 3 Preparation and Installation 3.3.2 Testing Installation Note The remote wireless module must be connected to a 2100 Series measurement module below it (or other compatible equipment) to function properly. By itself, it cannot measure anything; it is merely a radio frequency transmitter of data generated by the connected measurement module. When first powered up or after completing a connection, the remote will attempt to connect for 30 seconds.
2102 Wireless Communication Module Section 3 Preparation and Installation 3-6
2102 Wireless Communication Module Section 4 Programming 4.1 Section Overview This section describes how to set up the operation of a 2100 Parameter Module using Teledyne Teledyne Isco’s Flowlink for Windows software. Note The 2100 System requires Flowlink 4.1 or later. Earlier versions do not support 2100 System instruments. Flowlink Help 4.2 Flowlink Connections Detailed Flowlink instructions are beyond the scope of this manual.
2102 Wireless Communication Module Section 4 Programming RS-232 Serial Ports COM1 or COM2 2102 Power Option 1 12 VDC Cigarette Adapter Communication Cable Power Option 2 AC Adapter Base Unit Configuration Power Option 3 2191 Battery Module Note that the wireless module must be on top of the stack.
2102 Wireless Communication Module Section 4 Programming Table 4-1 Base Module Connect Cables Cable or Power Option (Refer to Fig. 4-1) Description Part Number Communication Cable 60-2004-046 or 60-5314-849 Links the upper communications port of the 2102 (and other 2100 Series Modules) to a PC’s 9-pin serial communication port. Power Option 1 60-2004-050 12 VDC Cigarette Lighter Adapter for “drive-by” data collection.
2102 Wireless Communication Module Section 4 Programming 4-4
2102 Wireless Communication Module Section 5 Maintenance 5.1 Maintenance Overview The 2100 Series system is designed to perform reliably in adverse conditions with a minimal amount of routine service requirements. Maintenance intervals are affected by many variables. The number of modules powered by a Battery Module, the Data Storage Rate, and type of sensor will all affect the battery life.
2102 Wireless Communication Module Section 5 Maintenance 5-2
2102 Wireless Communication Module Appendix A Replacement Parts A.1 Replacement Parts Diagrams and Listings Replacement parts are called out in Figure A-1. Reference the call-out in the adjacent table to determine the part number for the item. Replacement parts can be purchased by contacting Teledyne Teledyne Isco’s Customer Service Department. Teledyne Isco, Inc. Customer Service Department P.O.
2102 Wireless Communication Module Appendix A Replacement Parts 1 2 3 4 5 6 4 22 24 4 25 23 26 27 29 28 30 31 25 Figure A-1 Replacement Parts Diagram – 2102 Wireless Communication Module A-2
2102 Wireless Communication Module Appendix A Replacement Parts Table A-1 Replacement Parts Listing – 2102 Wireless Communication Module Item No. Fig. A-1 Part Number Description 1 231310106 SCREW, SELF TAPPING, #4 2 602003087 CLAMP SPACER 3 602004012 CAP ASSEMBLY, MALE CONNECTOR 4 202100669 O RING, .650 ID, .079 CROSS SECTION.
2102 Wireless Communication Module Appendix A Replacement Parts A-4
Warranty ℶ❐₼㦘㹡㦘⹂䓸德㒥⏒侯䤓⚜䱿♙⚺摞 Name and amount of Hazardous Substances or Elements in the product ᳝↦᳝ᆇ⠽䋼ܗ㋴ Hazardous Substances or Elements 捷ↅ⚜䱿 䪙 ∲ 䬝 ݁Ӌ䫀 ⒈㘨㣃 Component Name (Pb) (Hg) (Cd) (Cr(VI)) (PBB) 兎恾㨎 Circuit Boards X O O O O ⒈Ѡ㘨㣃 (PBDE) O ℶ❐₼㦘㹡㦘⹂䓸德㒥⏒侯䤓⚜䱿♙⚺摞᧶Name and amount of Hazardous Substances or Elements in the product O: 嫷䯉年㦘㹡㦘⹂䓸德⦷年捷ↅ㓏㦘⧖德㧟㠨₼䤓⚺摞⧖⦷ST/ 㪖屓⸩䤓棟摞尐㻑ⅴₚᇭ O: Represent the concentration of the hazardous substance in this component’s any homogeneous pieces is lower than the ST/ s
Teledyne Isco One Year Limited Factory Service Warranty * Teledyne Isco warrants covered products against failure due to faulty parts or workmanship for a period of one year (365 days) from their shipping date, or from the date of installation by an authorized Teledyne Isco Service Engineer, as may be appropriate. During the warranty period, repairs, replacements, and labor shall be provided at no charge.