Contents Safety Information.................................................37 Markings on the Product.......................................37 Environmental Information....................................38 Features................................................................38 Accessories Included............................................39 Standby Notifications.............................................39 TV Control Buttons & Operation............................
Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Don’t operate your TV in extreme ambient conditions as this may cause damage to your TV. In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains.
Environmental Information WARNING Do not ingest the battery, Chemical Burn Hazard (The accessories supplied with or) This product may contain a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
• Teletext TV Control Buttons & Operation • Headphone connection • Automatic programming system TV/AV • Manual tuning • Automatic power down after up to eight hours. + P/CH • Sleep timer + • Child lock • Automatic sound mute when no transmission. • NTSC playback 1. Standby/On button • AVL (Automatic Volume Limiting) 2. Source button • PLL (Frequency Search) 3. Programme +/- buttons • PC input 4.
Connect Power Specification IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. Plug the power cable to the mains socket outlet. Antenna Connection Connect the aerial or cable TV plug to the AERIAL INPUT (ANT-TV) socket or satellite plug to the SATELLITE INPUT (ANT SAT) socket located on the rear bottom side of the TV.
Remote Control 1. Source: Shows all available broadcast and content sources 2. Netflix: Launches the Netflix application, if this feature is supported by your TV 3. YouTube: Launches the YouTube application 4. Play: Starts to play selected media 5. No function 6. Rapid reverse: Moves frames backwards in media such as movies 7. Language: Switches between sound modes (analogue TV), displays and changes audio/subtitle language (digital TV, where available) 8. Red button 9. Green button 10.
Connections Connector Type Mini Scart Connection (bottom) Cables Device Mini Scart adapter cable VGA Connection (bottom) AUDIO IN PC/YPbPr Audio Connection (back) YPbPr/PC Audio Cable HDMI Connection (bottom&side) SPDIF SIDE AV HEADPHONE SPDIF (Optical Out) Connection (back) Side AV (Audio/Video) Connection (side) Side Audio/Video Connection Cable Audio/Video Cable Headphone Connection (side) YPBPR YPbPr Video Connection (back) YPbPr Connection Cable USB Connection (back&side) CI Connection
Direct, Single Satellite Cable or DiSEqC switch by using “ ” or “ ” buttons. Switching On/Off To Switch the TV On Connect the power cord to a power source such as a wall socket (220-240V AC, 50 Hz). To switch on the TV from standby mode either: • Press the Standby button, Programme +/- or a numeric button on the remote control. • Press the Standby button or Programme +/- on the TV. The TV will then switch on.
Note: Do not turn off the TV while initializing first time installation. Note that, some options may not be available depending on the country selection. Using SatcoDX Feature You can perform SatcoDX operations using the Installation>Satelite Settings menu. In the SatcoDX menu, there are two options regarding to the SatcoDx. You can download or upload SatcoDX data. In order to perform these functions a USB device must be connected to the TV.
other cables between the TV and the audio system (A/V receiver or speaker system). When ARC is active, TV does not mute its other audio outputs automatically. So you need to decrease TV volume to zero manually, if you want to hear audio from connected audio device only (same as other optical or co-axial digital audio outputs). If you want to change connected device’s volume level, you should select that device from the source list. In that case volume control keys are directed to connected audio device.
TV Menu Contents System - Picture Menu Contents 3D Settings Press to view 3D settings. Mode You can change the picture mode to suit your preference or requirements. Picture mode can be set to one of these options: Cinema, Game, Sports, Dynamic and Natural. Contrast Adjusts the light and dark values on the screen. Brightness Adjusts the brightness values on the screen. Sharpness Sets the sharpness value for the objects displayed on the screen. Colour Sets the colour value, adjusting the colours.
System - Sound Menu Contents Volume Adjusts the volume level. Equalizer Selects the equalizer mode. Custom settings can be made only when in User mode. Balance Adjusts whether the sound comes from the left or right speaker. Headphone Sets headphone volume. Please ensure before using headphones that the headphone volume is set to a low level, to prevent damage to your hearing. Sound Mode You can select a sound mode (If the viewed channel supports).
System - Options Menu Contents Conditional Access Controls conditional access modules when available. Language You may set a different language depending on the broadcaster and the country. Parental Enter correct password to change parental settings. You can easily adjust Menu Lock, Maturity Lock, Child Lock or Guidance in this menu. You can also set a new PIN or change the Default CICAM PIN using the related options.
Power Up Mode This setting configures the power up mode preference. Last State and Standby options are available. Virtual Remote Enable or disable the virtual remote feature. CEC With this setting you can enable and disable CEC functionality completely. Press Left or Right button to enable or disable the feature. CEC Auto Power On This function allows the connected HDMI-CEC compatible device to turn on the TV and switch to its input source automatically.
Internet Lock: If this option is set to ON, the open browser application in the portal will be disabled. Set to OFF to release the application again. General TV Operation Using the Channel List The TV sorts all stored stations in the Channel List. You can edit this channel list, set favourites or set active stations to be listed by using the Channel List options. Press the OK/TV button to open the Channel List.
Now/Next Schedule Navigate (Directional buttons): Press the Directional buttons to navigate through the channels and programmes. Options (OK button): Displays event options. Event Details (Info button): Displays detailed information about selected programmes. Filter (Blue button): Views filtering options. Programme Options Use the directional buttons to highlight a programme and press OK button to display Event Options menu. The following options are available.
PC Input Typical Display Modes AV and HDMI Signal Compatibility The following table is an illustration of some of the typical video display modes. Your TV may not support all resolutions.
Supported Video File Formats for USB Mode Video Codec Resolution Bit Rate MPEG program stream (.DAT, .VOB, .MPG, .MPEG), MPEG transport stream (.ts, .trp, .tp), MP4 (.mp4, .mov), 3GPP (.3gpp, .3gp), AVI (.avi), MKV (.mkv), ASF (.asf) MPEG1/2 MPEG4 Container 1080Px2@30fps, 1080P@60fps 40Mbps XviD Sorenson H.263 H.263 MPEG program stream (.MPG, .MPEG), MP4 (.mp4, .mov), 3GPP (.3gpp, .3gp), AVI (.avi), MKV (.mkv), ASF (.asf) MP4 (.mp4, .mov), AVI (.avi), MKV (.mkv), ASF (.asf) FLV (.flv), AVI (.
Supported Audio File Formats for USB Mode Audio Codec Sample rate Bit Rate Container MPEG1/2 Layer1 16KHz ~ 48KHz 32Kbps ~ 448Kbps MP3 (.mp3), AVI (.avi), ASF (.asf), Matroska (.mkv, .mka), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), WAV (.wav) MPEG1/2 Layer2 16KHz ~ 48KHz 8Kbps ~ 384Kbps MP3 (.mp3), AVI (.avi), ASF (.asf), Matroska (.mkv, .mka), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), WAV (.
Supported DVI Resolutions When connecting devices to your TV’s connectors by using DVI converter cable(DVI to HDMI cable - not supplied), you can refer to the following resolution information.
3D Mode To view 3D contents or programmes in 3D mode you should wear the passive 3D glasses. Note that this TV’s 3D feature works only with its specific 3D glasses. Cautions for 3D viewing For your safety; Read these safety precautions carefully before using the 3D function. • Pregnant women, seniors, people with heart problems or people who experience frequent drowsiness, as well as people who can get easily nauseous should refrain from watching 3D. • Prevent children under the age of 5 from watching 3D.
You can use this setting to shift the phase of the 3D left/right broadcast. 3D Depth Sense (depending on model) This setting enables the control of 3D depth. 3D Viewing Information Refer to the size/distance guidelines below to experience 3D in the best possible way. Viewing Distance 3,85 3,25 39 40 42 46 47 48 50 55 65 3,00 32 37 2,85 Viewing distance (m) 23 26 2,80 (inch) 2,75 Size First off all the TV should be in 3D mode.
Connectivity Wired Connectivity To Connect to a Wired Network • You must have a modem/router connected to an active broadband connection. • Ensure that Nero Media Home software is installed to your PC (for Audio Video Sharing function). See “Nero Media Home Installation” section.
Broadband ISP connection network wall socket LAN input on the rear side of the TV Configuring Wired Device Settings Network Type The Network Type can be selected as Wired Device, Wireless Device or Disabled, in accordance with the active connection to the TV set. Select this as Wired Device if you are connecting via an ethernet. Internet Speed Test Highlight Internet Speed Test and press the OK button. TV will check the internet connection bandwidth and display the result when complete.
If the selected network is protected with a password, please enter the correct key by using the virtual keyboard. You can use this keyboard via the directional buttons and the OK button on the remote control. Wait until the IP address is shown on the screen. This means that the connection is now established. To disconnect from a wireless network, highlight Network Type and press Left or Right buttons to set as Disabled.
If the wireless network does not function properly, try using the wired network in your home. Refer to the Wired Connectivity section for more information on the process. This standard allows you to view and play photos, music and videos stored in the media server connected to your home network. If the TV does not function using the wired connection, check the modem (router). If the router does not have a problem, check the internet connection of your modem.
Nero MediaHome Installation To install Nero MediaHome, please proceed as follows: Note: To use Audio Video Sharing feature, this software should be installed to your PC. 1. Enter the link below completely in the adressbar of your web browser. http://www.nero.com/mediahome-tv 2. Click the Download button on the opening page. The installation file will be downloaded onto your PC. 3. After the download is completed, double click on the installation file to start the installation.
button and press the OK button. Then highlight Add to Speed Dial option in the submenu and press the OK button again. Name and Address will be filled automatically according to the site you are visiting. Highlight OK and press the OK button to add. You can also use the Opera menu options to manage the browser. Highlight the Opera- button and press the OK button to see available page specific and general options. There are various ways to search or visit websites using the web browser.
VOD (video on demand) and catch-up TV services. The user can use play, pause, stop, forward, and rewind keys on the remote control to interact with the AV content. navigate through channels by pressing on the selected channel on the EPG grid. Please note that updating / refreshing the EPG information may take a while depending on your network and web service quality. Note: You can enable or disable this feature from the More Note: Internet connection is required for WEB based EPG informations.
FollowMe TV Feature Tap on the FOLLOW ME TV widget located at the bottom left of the screen of your mobile device to change the layout for FollowMe TV feature. Tap the play icon to start streaming of the content from the TV to your mobile device. Available if your device is in your routers operation range. Mirror Mode This mode of FollowMe TV feature is enabled by deafult and allows streaming the content from any other selected TV sources and Media Browser.
TELEFUNKEN® Markenlizenz: TELEFUNKEN Licenses GmbH Vertrieb: Vestel Germany GmbH, D-85748 Garching bei München TELEFUNKEN® licensed by: TELEFUNKEN Licenses GmbH Imported by: Vestel Germany GmbH, D-85748 Garching/Munich 1 1 1 Die Marke TELEFUNKEN ist eine eingetragene Marke der TELEFUNKEN Licenses GmbH.
