User's Manual

Section 7 - Programming (Continued)
67
SW3 Positions 1-3 Repositioning of
tele
Pilot
Transmitter Motion Switch Functions. (Standard
configuration all “OFF”).
S3 positions 1 through 3 can change the functional
positions of the switches controlling hoist, trolley and
bridge. This reconfiguration does NOT affect receiver
wiring. As these switches are changed the motor controls
are moved.
Standard, Motor 1 is H (Hoist) Motor 2 is T (Trolley)
and Motor 3 is B (Bridge). The standard configuration
(all switches OFF) is, starting at the top right hand pair
of buttons on the transmitter, Motor 1. Moving down to
the middle two right hand pair of buttons that is Motor 2.
The bottom pair on the right is Motor 3. This is indicated
the display “Switch config: H,T,B. The order of Hoist,
Trolley and Bridge will vary as S3-1 to 3 switch
positions are changed. For an example of switch
configurations versus switch settings see Section 7-.13.
Repositioning of Pendant Transmitter Motion Switch
Functions. The settings match the operation of the
tele
Pilot
.
SW3 Position 4 And 8 Time-out-timer Disable.
(Normally turned “OFF”).
Disables the transmitter time-out-timer if turned ON. If
the time-out-timer is active, the length of time for time
out can be selected for numbers of minutes till shut
down. The minutes are selectable in one-minute steps
from 1 to 10 and five minutes steps up to an hour. Tap
on the “Timer” arrow and scroll down through the
number of minutes and tap on the desired number.
Positions 5-7 Special Crane Control Configurations.
(Standard all “OFF”).
Section 6. Wiring shows all the different crane
configurations and the switch positioning needed to
achieve them. The standard transmitter comes with the
output standard output configuration. For special crane
control configurations program S3 positions 5-7 to
match the programming information shown for the
respective wiring diagram. When any of the special
crane configuration switches is turned ON, the words
“Crane control enabled” appears on the display and
Main/Aux disappears.
Position 8, Same as Switch Position 4. See write up
for switch 4 above (Normally turned “OFF”).
Main/Aux Menu for controlling the “AUX 3” Push
Button
This menu shows only if no Special Crane
Configurations are selected (Switch 3 positions 5-7).
This programming redefines the function of the (AUX 3)
button just above the E-STOP.
(If a three motor crane use “Aux”, for standard four
motor use “Motor ”, for Select function use Select).
If replacing a pendant transmitter
: if Switch 4 on the
pendant transmitter has position 1 “OFF” and position 2
“ON” use “Motor”, if Switch 4 has position 1 “ON” and
position 2 “ON” use “Select”.
For
three motor stand system
this button is an auxiliary
relay control button. (AUX 3).
For
four motor systems
this button controls a main and
aux motor such as a hoist. (See Section 5. Operation for
details on the operation of this button.) To program a
fourth motion select (Motor). This four motor
application can only be used with special crane
configuration TABLE 2(H) Standard 2-Speed 4 Motor
System. The AUX 3 button becomes a switch to toggle
between “A” and “B” or both. Where “A” and “B” are
main and auxiliary motors respectively. The main motor
output is motor 1 and the auxiliary motor output is motor
4.
For up to
5 motors
using the
select function
this button
is available to use select relays. This select function can
only be used with special crane configuration TABLE
2(I) Standard 2-Speed 3, 4 & 5 Motor System using
Select. To program in the select function tap the word
“Select”.
Tandem For Hoist, Trolley or Bridge. (Normally
checked).
This function appears if a four motor system or select
function is chosen. Normally the box is checked
meaning “Both A and B” operation is enabled (both
MAIN and Aux or Select 1 and Select 2 can be ON at
the same time). Removing the check from the box by
tapping on it disables the “Both” function. (“A” and “B”
will not come ON at the same time). This function maps
to Pendant Switch 4 position 3, if SW4 position 3 is
switched “ON” un-check Tandem box on PDA.