User Manual
BTR-30N, TR-30N, TR-32N 73
TR-30N Beltpack Screen
Flowchart
11/05/2019
Rev1
TR-30N Beltpack Screen Flowchart
19u 01 174.125 518.225 521.525 N7ic10 95 Pct Po Aut S9L 02 Ptt LEd on
19u 01 174.125 518.225 521.525 M7ic10 Lbt ofF Po Aut S9L 02 Ptt LEd on
19u 01 FAc dEF FAc dEF FAc dEF bAt AL
Special Key Functions
Tx Power and
Receiver RSSI
Beltpack
Identification
Software Band
Software Version ClearScan Talk Button Options Stage Announce (SA)
Wireless Talk Around
(WTA) Lockout 1
st
Use Default
Factory Reset
Default
Hi 3 i d 1-1 bnd A10 CLr Scn tb LAt SA on tA on Loc on 01A 01 FAc rES
i d 1-1 303 004 01A tb oFF SA oFF Loc oFF 01A 01
01A 01
01A 01
TX
R1
GP
TX
R1
CH
GP
TX
R1
CH
GP
TX
R1
CH
Group / Channel
TX Frequency
RX1 Frequency
GP
TX
R1
CH
R2
GP
TX
R1
CH
R2
GP
TX
R1
CH
GP
TX
R1
CH
R2
RX2 Frequency
Microphone Gain
Battery Gauge
TX Out
p
ut Power
Squelch Level
GP
TX
R1
CH
R2
Push-to-Talk / TX
Lights On/Off
GP
TX
R1
CH
R2
[MENU]
GP
TX
R1
CH
General Notes: 1) Pressing [MENU] will bail out of editing without any changes.
2) Groups 01 to 18 are factory groups. 19u – 30u are user defined
groups.
3) = Flashing.
[MENU]
[MENU]
[MENU]
[MENU]
[MENU]
[MENU]
[MENU]
GP
TX
R1
CH
[SET]
[SET]
GP
TX
R1
CH
[SET]
[SET]
[SET]
GP
TX
R1
CH
If Factor
y
Grou
p
GP
TX
R1
CH
[SET]
[SET]
GP
TX
R1
CH
If Factor
y
Grou
p
[SET]
If Factor
y
Grou
p
GP
TX
R1
CH
R2
[SET]
[SET]
NOTE:
0 = No Gain
15 = Full Gain
GP
TX
R1
CH
R2
GP
TX
R1
CH
[SET]
[SET]
GP
TX
R1
CH
[SET]
MENU Options:
Lbt = Low Battery Tone
bAt = Battery Type
AL = Alcaline
n i = NiMH
GP
TX
R1
CH
[SET]
[SET]
MENU Options:
Aut = Automatic Selection
…….. between 10 and 50mW
10 = 10 mW TX Power
50 = 50 mW TX Power
100 = 100 mW TX Power
[SET]
GP
TX
R1
CH
R2
MENU Options:
00 = Open
01 = High noise before Sql.
02 = Mid. noise before Sql.
03 = Low noise before Sql.
04 = Quiet before Sql.
[SET]
GP
TX
R1
CH
R2
MENU Options:
Ptt = Push-to-Talk
Pt tr = Push-to-TX
Pt trL = Push-to-TX
Lockouts Enabled
Pt trn = Push-to-TX
Lockouts Enabled,
No busy signal
[SET]
[SET]
[SET]
[SET]
[MENU]
Hold [MENU] as
powering-up unit
Sets unit to
Group 01A,
Channel 01, with
01 flashing. User
must set channel
number.
Sets unit to
defaults
All user-defined
groups are
retained
GP
TX
R1
CH
R2
[MENU]
Hold [MENU]
for 2 seconds
GP
TX
R1
CH
R2
Hold [MENU] +
[SET] + [ ] + [ ]
for 2 seconds
Press [MENU]
to exit to
normal menus
Hold [ ] for 2
seconds
GP
TX
R1
CH
R2
GP
TX
R1
CH
R2
[SET]
[SET]
Press [MENU]
to exit to
normal menus
Function:
View ID assigned to
beltpack by base
station.
May also be used to
change beltpack ID.
Hold [ ] for 2
seconds
GP
TX
R1
CH
R2
Displayed for
1 second
GP
TX
R1
CH
R2
Displayed for 1
second or when
[ ] released
Back to
normal menu
Hold [MENU] +
[SET] for 2 sec.
GP
TX
R1
CH
R2
GP
TX
R1
CH
R2
After 10 seconds
best group selected
GP
TX
R1
CH
R2
GP
TX
R1
CH
R2
[SET]
[SET]
Group / Channel Screen
Hold [SET] and
press [TALK]
GP
TX
R1
CH
R2
GP
TX
R1
CH
R2
Function:
Talk button operation.
LAt = Talk latch on
oFF = Talk disabled
Ptt = Momentary
[TALK]
[TALK]
Hold [SET] and
press [SA]
GP
TX
R1
CH
R2
GP
TX
R1
CH
R2
[SA]
[SA]
Hold [SET] and
press [WTA]
GP
TX
R1
CH
R2
[WTA]
Options in menu:
on = Momentary
Lon = Latch
oFF = WTA disabled
[WTA]
Hold [ ] + [ ] for
2 seconds
GP
TX
R1
CH
R2
Hold [ ] + [ ]
again for 1 second
GP
TX
R1
CH
R2
Function:
Menu items can be
viewed but not changed
when activated.
GP
TX
R1
CH
R2
GP
TX
R1
CH
R2
Sets unit to
Group 01A,
Channel 01, with
01 flashing. User
must set channel
number.
Sets unit to
defaults
All user-defined
groups are
erased
Function:
Display current
TX power of unit:
hi = 50mW
Lo = 10mW
-- = Off
Display receiver
strength; 0 – 5:
0 = Clear
5 = Strong Signal
GP
TX
R1
CH
GP
TX
R1
CH
GP
TX
R1
CH
R2
[SET]