User Manual

ManualsBrandsTelex ManualsAudio for Video2-Channel UHF/VHF Wireless Beltpack, F10 Band, A5F Connector

74 BTR-30N, TR-30N, TR-32N

TR-32N Beltpack Screen Flowchart

11/05/2019

Rev1

TR-32N Beltpack Screen Flowchart

19u 01 174.125 518.225 521.525 N7ic 10 95 Pct Po Aut S9L 02 Ptt hP 4-P Au oFF Au 05 LEd on

19u 01 174.125 518.225 521.525 M7ic 10 Lbt ofF Po Aut S9L 02 Ptt hP 4-P Au oFF Au 05 LEd on

19u 01 FAc dEF FAc dEF FAc dEF bAt AL hP Add Au 1

hP SEP

Special Key Functions

Tx Power and

Rx1 / Rx2 RSSI

Beltpack

Identification

Software Band

Software Version ClearScan

Talk Button

Options

Stage Announce

(SA)

Wireless Talk

Around (WTA) Lockout 1

Use Default

Factory Reset

Default

hi 3 5 i d 1-1 bnd A10 CLr Scn 1 Lon SA on tA Pb Loc on 01A 01 FAc rES

i d 1-1 403 004 01A 1 off SA oFF Loc oFF 01A 01

01A 01 1 on

01A 01

Group / Channel

TX Frequency

RX1 Frequency

RX2 Frequency

Microphone Gain

Battery Gauge

TX Out

ut Power Squelch Level

Push-to-Talk / TX

Headphone Audio

Auxiliary Input

Lights On/Off

[MENU]

General Notes: 1) Pressing [MENU] will bail out of editing without any changes.

2) Groups 01 to 18 are factory groups. 19u – 30u are user defined

groups.

3) = Flashing.

[MENU]

[MENU] [MENU]

[MENU]

[SET]

If Factory Group

[SET]

If Factory Group

[SET]

If Factory Group

[SET]

NOTE:

0 = No Gain

15 = Full Gain

[SET]

MENU Options:

Lbt = Low Battery Tone

bAt = Battery Type

AL = Alcaline

n i = NiMH

[SET]

MENU Options:

Aut = Automatic Selection

…….. between 10 and 50mW

10 = 10 mW TX Power

50 = 50mW TX Power

[SET]

MENU Options:

00 = Open

01 = High noise before Sql.

02 = Mid. noise before Sql.

03 = Low noise before Sql

04 = Quiet Before Sql.

[SET]

MENU Options:

Ptt = Push-to-Talk

Pt tr = Push-to-TX

Pt trL = Push-to-TX

Lockouts Enabled

Pt trn = Push-to-TX

Lockouts Enabled,

No busy signal

[SET]

MENU Options:

4-P = Output for any 4-Pin headset or single headphone 5/6-Pin headset

Add = Add 1 and 2 audio in a dual headphone 5/6-Pin headset

SEP = Separate 1 and 2 audio in a dual headphone 5/6-Pin headset

[SET]

[MENU]

Auxiliary In Level

(Only if Aux In Active)

[MENU]

[SET]

NOTE:

0 = No Gain

15 = Full Gain

[SET]

Hold [MENU]

for 2 seconds

Hold [MENU] +

[SET] + [ ] + [ ]

for 2 second

Press [MENU]

to exit to

normal menus

Hold [ ] for 2

seconds

Function:

Display current

TX power of unit:

hi = 50mW

Lo = 10mW

-- = Off

Display receiver 1 and

2 signal strength; 0 – 5:

0 = Clear

5 = Strong Signal

[SET]

Press [MENU]

to exit to

normal menus

Function:

View ID assigned to

beltpack by base

station.

May also be used to

change beltpack ID.

Hold [ ] for 2

seconds

Displayed for

1 second

Displayed for 1

second or when

[ ] released

Back to

normal menu

Hold [MENU] +

[SET] for 2 sec.

After 10 seconds

best group selected

[SET]

Group / Channel Screen

Hold [SET] and

press [TALK]

Function:

Talk button operation.

Lon = Talk Latch on

oFF = Talk off

on = Momentary on

[TALK]

Hold [SET] and

press [SA]

[SA]

Hold [SET] and

press [WTA]

[WTA]

Options in menu:

Pb = Push button

1L = Audio 1 Latch

2L = Audio 2 Latch

12L = Audio 1&2 Latch

PbL = Push button Latch

oFF = WTA disabled

1 = Audio 1 M

2 = Audio 2 M

12 = Audio 1&2 M

[WTA]

Hold [ ] + [ ] for

2 second

Hold [ ] + [ ]

again for 1 second

Function:

Menu items can be

viewed but not changed

when activated.

Hold [MENU] as

powering-up unit

Sets unit to

Group 01A,

Channel 01, with

01 flashing. User

must set channel

number.

Sets unit to

defaults

All user-defined

groups are

retained

Sets unit to

Group 01A,

Channel 01, with

01 flashing. User

must set channel

number.

Sets unit to

defaults

All user-defined

groups are

erased

MENU Options:

Au 1 = Aux. in to Audio 1

Au 2 = Aux. in to Audio 2

Au 12 = Aux. in to Audio 1 & 2

Au oFF = Aux. input off.

[MENU]