Telex® User Instructions Model PS2000L Power Supply Audiocom ® Intercom Systems ®
FCC Statement This equipment uses, and can radiate radio frequency energy that may cause interference to radio communications if not installed in accordance with this manual. The equipment has been tested and found to comply with the limits of a Class A computing device pursuant to Subpart J, Part 15 of FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Table of Contents Description . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . 6 Unpacking . . . . . . . . . . . . 6 Configuration Switches . . . . . . . . . . 6 . . . . . . . . 7 Intercom Channel Connections Power-Up Check . Specifications . . . . . . . . . . . . 10 . . . . . . . . . . 11 . . . . . . .
Audiocom® Description The PS2000L is a versatile power supply that can be used in a variety of Audiocom intercom system applications. It directly accepts any AC input power from 100 to 240 VAC, 50/60 Hz, and it can be configured to power two separate intercom channels or one large intercom channel with twice the intercom station capacity. Additionally, the PS2000L can be configured for compatibility with Clear-Com* Intercom Systems. The PS2000L can be rack mounted or used on a desktop.
2. Channel Status Indicators and Reset Pushbutton: The indicators are green for normal operation and red when there is an overload or short circuit. The Reset pushbutton restores normal operation after the short-circuit or overload has been located and fixed. 3. Universal AC Power Input: The PS2000L accepts any input power in the range of 100-240 VAC, 50/60 Hz. 4.
Audiocom® Installation Unpacking The package contains the following items. Contact the shipper or your Audiocom dealer immediately if anything is damaged or missing. Detach and fill out the registration card and return it to Telex to properly register your PS2000L.
Figure 2. Audiocom / Clear-Com Selector Switch (Top Cover Removed) Intercom Channel Connections Channel Capacity: When connecting intercom stations to the PS2000L, determine the total current for all stations on each channel. The total per channel should not exceed 2A. If you exceed this limit, the PS2000L will provide an overload indication. Note that if you are using DC wallpacks with any intercom stations, you do not need to add the current consumption of those stations to the total current.
Audiocom® TYPICAL 1-CHANNEL CABLE WIRING 3 2 Pair 1 3 2 1 Pair 2 1 (Both wires) Shield Shield Cable Type: 22AWG Stranded, 2-Pair Twisted-wire, with Shield Connector Type: 3-Pin XLR Audio (Neutrik or Switchcraft)* Pin 1: Common Denotes twisted pair. Pin 2: Channel Audio / Power Pin 3: Channel Audio / Power Denotes shield.
Figure 4. Typical connections using a single PS2000L Power Supply to power two channels.
Audiocom® Figure 5. Using two PS2000L Power Supplies to provide a greater capacity on each channel. Power-Up Check 1. ☞ Plug in any DC wallpacks that are being used with individual intercom stations. If you plug in DC wallpacks after applying power to the PS2000L, you may get an overload indication at the PS2000L. This is because the stations that are being powered by wallpacks will draw current from the PS2000L until their own DC supplies are connected. 2.
Specifications General Input Power Requirements: 100 to 240 VAC, 50 / 60 Hz Output Power (each channel) 21 ± 1 VDC, 2A Dimensions: 1.75" (44.5 mm) high x 8.25" (209.5 mm) wide x 10.31" (261.9 mm) deep Weight: approximately 2.5 lb (1.13 kg) Environmental Requirements: Storage: -20°C to 80°C; 0% to 95% humidity, non-condensing Operating: 0°C to 50°C; 0% to 95% humidity, non-condensing Intercom Channels General Connector Type: One XLR-3M audio connector for each channel.
Audiocom® Factory Service and Parts Information When returning equipment for repair include your return address, telephone number and proof of date of purchase, along with a description of the problem.* The address for Audiocom equipment returns and parts information is: Service Department Telex Communications, Inc. West 1st Street Blue Earth, Minnesota 56013 U.S.A. Telephone: (507) 526-3205 (Collect calls not accepted) Warranty Repairs - If in warranty, no charge will be made for the repairs.
Notes: 13
Audiocom® Notes: 14
Notes: 15
® TELEX COMMUNICATIONS, INC. 9350-7333-015 Rev. A 3 , 8/97 9600 Aldrich Ave. So., Minneapolis, MN 55420 U.S.A.