Telematics Platform 1 (TP1) Installation and User Manual
PCI Private Limited 35 Pioneer Road North Singapore 628475 Copyright © 2019 PCI Private Limited. All rights reserved. PCI Private Limited is a trademark of PCI Private Limited. All other trademarks are the property of their respective owners. PCI Private Limited endeavours to ensure that the information in this document is correct and fairly stated, but PCI Private Limited is not liable for any errors or omissions.
1. Component Overview 2. FCC, IC and CE Compliance Statements 3. Installation Planning 4.
Component Overview Telematics Platform 1 (TP1) Characteristics Requirements Conditions Operating Temperature -30° C to 70° C (-35° F to 158° F) Operating Voltage 12 or 24 Volts DC Operating Current 500mA max @ 12V 250mA max @ 24V Sleep current 10mA max @ 12V Connector Pinouts 12-pin Main Connector DT13-12PA Pin # Function Pin # Function 1 VBATT 7 CAN1_H 2 DIGITAL IN 8 CAN1_L 3 CAN2_H 9 CHASSIS GROUND 4 CAN2_L 10 DIGITAL OUT 5 CHASSIS GROUND 11 CHASSIS GROUND 6 IGNITION SEN
The TP1 system has no user-serviceable parts. The TP1 contains a permanent lithium coin cell for maintaining the real time clock; proper recycling or disposal per local law is required for all components of the TP1.
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 28cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must be fixed to US operation channels only.
IC Compliance Statement This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
CE Compliance Statement This device complies with Directive 2014/53/EU issued by the Commission of the European Community. A minimum separation distance of 28 cm must be maintained between the user’s body and the device, including the antenna during body-worn operation to comply with the RF exposure requirements in Europe. - Frequency bands and Powers a.
b.
Wifi: 802.11b 2.4GHz 20MHz BW 802.11g 2.4GHz 20MHz BW 802.11n 2.4GHz 20MHz BW 802.11n 2.4GHz 40MHz BW 802.11n 5GHz 20MHz BW 802.11n 5GHz 40MHz BW 802.
- WLAN 5GHz: Operations in the 5.15-5.35GHz band are restricted to indoor usage for all countries. - For single module: In all cases assessment of the final product must be mass against the Essential requirements of the Directive 2014/53/EU Articles 3.1(a) and (b), safety and EMC respectively, as well as any relevant Article 3.2 requirements. The maximum antenna gain for frequency 850 MHz is 0.65 dBi; for frequency 1900 MHz is 2.68 dBi.
Installation Planning Safety, Reliability, and Accessibility • Use eye protection when using a drill/performing work that may be hazardous to the eyes. • Use ear protection in noisy work areas. • Wear appropriate clothing/uniforms and safety shoes. • Maintain three points of contact when climbing in and out of cab. • Make sure you know what is behind the area before you drill. • Install equipment so it will not cause damage to the vehicle or work loose over time.
• it does not limit a passenger’s leg room or block access to any other compartments. • it does not interfere with anyone entering or exiting the vehicle cab. • it is not likely to impact the driver or passenger in case of an accident or collision. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION DO NOT locate the Product where it: • obstructs the driver’s field of vision. • distracts the driver from the driving task.
Mounting Options: Option 1: Mounting without Bracket Mounting Screw Locations. There are a total of 4 mounting screw holes, one at each corner, as pointed to by the red arrows below. Two of the holes are slightly elongated for tolerance purpose. Fastening screws (M5 bolts) and washer are provided Units are in millimeters.
Option 2: Mounting with Plastic Bracket Step 1: Mount Bracket to Surface First Step 2: Mount TP1 onto Bracket
There are a total of 4 mounting screw holes, one at each corner, as pointed to by the red arrows below. Two of the holes are slightly elongated for tolerance purpose. 4 x Fastening screws (M5 bolts) and washer are provided Units are in millimeters.
