Installation Instructions

ManualsBrandsTelit ManualsComputers & AccessoriesSkyHub Wireless Telematics Hub

SkyBitz SkyHub & SkyCamera Installation 1

SkyHub with SkyCamera Installation

SkyHub Componets

• SHB1000 SkyHub Tracking Device

• SkyHub Mounting Bracket

• 6, 10-32 Tamper Proof Screws

• SkyHub Short Shroud

• 6, 1/8 Inch sealing Blind Rivets

• 3M Primer 94 Ampoule

Tools Required:

• Power Drill and 1/8 in Drill Bit

• 5/32 Inch Pin in Hex Tamper Proof Screwdriver

• Blind Rivet Tool

• 50/50 Isopropyl Alcohol/Water Solution

• Clean Rags

• Tape Measurer

SkyHub Mounting Location

The SkyHub will be mounted to the exterior front wall of a Dry Van Trailer. The locations described

below are recommended for optimal communications with the SkyCam. The general dimensions

noted may be adjusted to avoid mounting on top of any logos or asset identification. For a Plate

Nose Trailer, the SkyHub will be mounted to the front wall horizontally, about 3 inches down from the

bottom of the top rail, and about 6 inches from the roadside edge with the connector on the left.

For a Sheet and Post Nose Trailer, the SkyHub will be mounted to the front wall vertically, about 3

inches down from the bottom of the top rail, and about 6 inches from the roadside edge with the

connector at the top.

Summary of content (6 pages)

PAGE 1
SkyHub with SkyCamera Installation SkyHub Componets • • • • • • Tools Required: SHB1000 SkyHub Tracking Device SkyHub Mounting Bracket 6, 10-32 Tamper Proof Screws SkyHub Short Shroud 6, 1/8 Inch sealing Blind Rivets 3M Primer 94 Ampoule • • • • • • Power Drill and 1/8 in Drill Bit 5/32 Inch Pin in Hex Tamper Proof Screwdriver Blind Rivet Tool 50/50 Isopropyl Alcohol/Water Solution Clean Rags Tape Measurer SkyHub Mounting Location The SkyHub will be mounted to the exterior front wall of a Dry Van Trail
PAGE 2
SkyHub Tracking System Installation • Use the SkyHub bracket as a template to mark the bracket location, and the 3 VHB tape locations on the wall • Prep the trailer wall for the 3 VHB tape mounting surface locations o Clean with IPA solution o Abrade lightly with Scotch-Brite pad o Clean again with IPA solution o Prime with 3M Primer 94 and wait at least 3 minutes Remove the liner from the 3 VHB tape locations on the bracket, place the bracket onto the mounting location on the trailer wall, and firmly pr
PAGE 3
• Fasten the Short Shroud to the SkyHub with two, 10-32 tamper proof screws SkyCamera Installation Components and Tools • • • • • • • • • SkyCamera with SkyCamera Mounting Bracket 4, 10-32 Tamper Proof Screws and 5/32 Inch Pin in Hex Tamper Proof Screwdriver 8, 3/16 inch stainless steel rivets SkyCamera circular alignment tool 1.
PAGE 4
SkyCamera Installation • • • • • • • • • Use the SkyCamera bracket as a template to mark the location of the bracket and the 1.75inch camera hole Drill the 1.
PAGE 5
• Install the camera to the bracket with four 10-32 tamper proof screws • Remove the Barcode label taped to the SkyCamera and install it on the front of the trailer next to the 7-way connector FCC Compliance: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received including interference that may cause undesired operation.
PAGE 6
SkyBitz SkyHub & SkyCamera Installation 6