User's Manual
The EcoSmart Energy Management System
The EcoSmart Energy Management System is designed to reduce
HVAC energy consumption without interfering with an
occupant’s comfort.
EcoSmart thermostats will automatically learn and adapt to the
heating and cooling patterns of each room. For example, a room
on the east side of a building will receive direct sunlight in the
morning and will either need less HVAC heating or more HVAC
cooling. However, as the day progresses, the room will need
more HVAC heating or less HVAC cooling as it moves into the
shade. An EcoSmart thermostat will continually monitor the
room, learn its patterns, and adjust its heating and cooling
profiles accordingly.
EcoSmart thermostats also learn and adapt to occupant
schedules. When a room is unoccupied, an EcoSmart thermostat
will enter an energy saving mode, allowing the room to drift
away from the desired setpoint. During this drift period, the
thermostat will operate the HVAC unit less often, reducing
energy costs. When the room becomes occupied again, the
EcoSmart Recovery Time™ technology built into each thermostat
will return the room to the setpoint without the occupant
noticing
FCCNotice
This equipment has been tested and found to comply with the
limits for a class B digital device pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If the equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipm
ent and
the receiver.
Co
nnect the equipment into an outlet on
a circuit
different from that to which the receiver is
connected.
Co
nsult the dealer or experienced radio/
TV technician
for help.
In order to
maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-
approved equipment is likely to result in interference to radio
and TV reception. The user is cautioned that changes and
modifications made to the equipment without the approval of
the manufacturer could void the user’s authority to operate the
equipment.
To satisfy RF exposure requirements, this device and its
antennas must operate with a separation distance of at least 20
cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC ID:
XV6SS6205
Conventi
onsUsedinthisGuide
This is an infor
mational tip, used to convey
relevant but not necessarily urgent
information.
This is a warning, used to convey important
information.
This is a strong warning, used to convey
urgent and often safety-related information.
Chapter Names
Main chapters in this manual will have headings in large green
font as shown above. Main chapter names also appear in the
footer.
Sub-Chapter Names
Within the main chapters will be relevant sub-chapters, which
are presented with bold, black headings as shown above.
Footers
Footers contain the document name, chapter name, document
version number and page number, as shown here:
Procedure: Steps Described Here
Procedural Steps are indicated as such in the heading, which
begins with the word, “Procedure:” as shown above. The steps
are outlined as shown in the following example:
Step 1 Navigate to the Config Menu > Alert Setup.
Step 2 Click the Add New Alert Trigger button in the top left
corner of the Alert Setup Screen.
Step 3 Enter a descriptive Alert Name.
Assistance with troubleshooting begins with the red
“Troubleshooting” header as shown above.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation.