PHONECELL® SX6P-200C CDMA Fixed Cellular Phone USER MANUAL 02/21/05 Part Number 56033201
QUICK CONNECTION GUIDE Spike Antenna Phonecell SX6P-200C Fixed Cellular Phone LIST OF COMPONENTS Phonecell® SX6P Desktop Phone Spike Antenna AC Power Cord Before installing your Phonecell® SX6P, carefully remove the contents from the shipping carton and check for evidence of shipping damage. If damage is found, contact your Authorized Telular Distributor or shipping agent immediately.
SX6P MENU STRUCTURE 1. Phone Book Menu View Add Edit Erase 2. Call History Missed Outgoing Incoming Erase History Last Call Time Air Time Clear Air Tim^ 3. Time/Alarm Alarm Time Format Date Format 4. Ring/Alert Ring Tone Ring Volume 1 Min Alert Service Alert Alarm Tone 5. Phone Settings Banner LCD Contrast DTMF Length Key Volume Auto Send Time Freq Dial Num Language Dial Tone Type Selftest Cycle 6. Phone Info My Phone # Version Tech Mode 7.
SAFE OPERATION INSTRUCTIONS IMPORTANT! Before installing or operating this product, read the SAFETY INFORMATION section of this manual. • Install unit indoors. • Install unit on hard, flat surface for proper ventilation. • Do not expose unit to rain or moisture. • Do not place unit on or close to sources of heat. Please see the IMPORTANT NOTICES, SAFETY INFORMATION, and WARRANTY sections of this manual for important information on use, warranty, and indemnification.
Table of Contents Quick Connection Guide ...................................................................................................i List of Components............................................................................................................i SX6P Menu Structure ........................................................................................................ii Safe Operation Instructions .......................................................................................
Phone Settings ................................................................................................................15 Banner .......................................................................................................................................15 LCD Contrast .............................................................................................................................15 DTMF Length.....................................................................................
SX6P Setup RUIM Card Installation (RUIM Model Only) Consult your service provider to determine if your unit requires the use of a RUIM (Removable User Identity Module). If it is a RUIM model, your SX6P will only be able to place emergency calls until you install a RUIM card. It will not receive calls or allow non-emergency outgoing calls without the RUIM card installed. For an explanation of how to configure your RUIM once your SX6P is set up, see RUIM Usage on page 5. 1.
Battery Installation Note: The battery is an optional accessory that may or may not be available. Consult your service provider. 1. If necessary, remove the screw that may be holding the battery access door located on the bottom of the unit - see Figure 3. 2. Press the battery access door tabs and remove the battery access door. 3. Install the Telular rechargeable battery pack into the battery pack area and connect wires. 4. Reinstall the battery access door using the screw - see Figure 4.
Connecting the Handset Before you use can use the SX6P, you must connect the handset cable. 1. Connect the handset cable to the phone jack - see Figure 7. 2. Connect the handset cable to the handset - see Figure 7. Phone jack Handset cable Handset Figure 7 – SX6P handset connection. Wall Mounting 1. Remove the mounting clip from the cradle and re-insert it with the tab pointing up - see Figures 8 and 9.
3. Install the screws (not supplied) into the wall, leaving a gap of approximately 3 mm (1/8 inches) between the screw head and the wall. 4. Align the mounting holes with the screws and mount the SX6P onto the screws - see Figures 10 and 11. 83 mm (3-1/4 inches) Mounting Holes Figure 10 – SX6P mounting hooks. Figure 11 – Mount the SX6P onto the screws. Connecting the SX6P to AC Power 1.
RUIM Usage (RUIM Models Only) Your service provider may require you to install a RUIM (Removable User Identity Module) in your SX6P for it to operate normally (see RUIM Card Installation on page 1 for details). Without a RUIM, these SX6P models will reject incoming calls and allow only emergency outgoing calls.
Getting to Know Your SX6P Function Keys LCD Screen - Displays icons, information, and menu options necessary to operate the SX6P. Clear - To clear an entry, erase a digit during entry, or to go back one menu level. Message - To access voicemail or to send an SMS (text message). Store - Used to store an entry. Menu - Used to access phone settings and features. Power - Used to power the unit on and off.
LCD Screen Icons Icons displayed on the LCD screen indicate the features that are in use, the status of the phone, signal strength and battery status - see Figure 14. Alarm - Indicates that the alarm feature has been set. Message - Displays when a new text or voicemail message has been received. Speaker - Indicates “listenonly” speaker is activated. Off-Hook - Indicates handset is off the cradle. Battery - Indicates the level of battery power. The more bars, the more power.
Call Functions Making Calls 1. Pick up the handset or press [Speaker] (listening only). The SX6P is now “off-hook.” 2. Listen for dial tone. 3. Dial the phone number. The dialed number will be displayed. The name will also be displayed if it is stored in the phone book. Correcting Dialing Errors • • To erase one digit, press [Clear] once. To erase all digits, press and hold down [Clear] until all digits are erased. Redialing the Last Telephone Number Dialed 1. Pick up the handset or press 2.
Placing a Call on Hold 1. During a call, press [Hold]. (A notification will display in the upper right corner of the LCD display.) 2. To reactivate the call, press [Hold] again. 3-Way Calling Contact your service provider regarding the availability of 3-way calling. To perform a 3-way call: 1. Place the first call and wait until it connects. 2. After the first call is connected, dial the second number. 3. Press [Flash]. This connects the second call and puts the first call on hold. 4.
Sending a Text Message 1. Press [Message]. 2. Select 3: Create Message. 3. Select 1: New Message or 2: Sent Messages. 4. Select 1: From Phonebook or 2: Enter Number. (If you select From Phonebook, your phone book entries will be displayed alphabetically. Select an entry and press [Store] to initiate a message to that number.) to continue.) (If you select Enter Number, use your keypad to enter a number and press 5. Type the message using the keypad.
Phone Book The SX6P can be programmed to store frequently called numbers via an electronic phone book. The SX6P phone book can hold up to 99 entries. Speed Dialing by Location To speed dial a phone book entry: • • For entries 1-9 – Lift the handset and hold down the location number until it dials. For entries 10-99 – Lift the handset, press the first digit and then hold down the 2nd digit until it dials. Searching the Phone Book and Dialing a Phone Book Entry 1. Press [Menu] to access the main menu.
Editing a Phone Book Entry 1. Press [Menu] to access the main menu. 2. Select 1: Phone Book. 3. Select 3: Edit. There are two options to locate an entry for editing: 1. Name - View all entries sorted alphabetically. To narrow your search, use your keypad to enter the first letter of the entry you’re looking for (for example, press 5 once to display the “J” listings; press 5 three times to display the “L” listings). 2. Location - View all entries sorted by their two-digit location 01 through 99.
3. Select 4: Erase History and use the up arrow ( 4. Press ) to select Erase. [Store] to erase the Call History. Viewing Last Call Time To display the duration of the previous call: 1. Press [Menu] to access the main menu. 2. Select 2: Call History. 3. Select 5: Last Call Time. Viewing Total Air Time To display the total air time used by the phone since its memory was last cleared: 1. Press [Menu] to access the main menu. 2. Select 2: Call History. 3. Select 6: Air Time.
Ring / Alert The SX6P is capable of supporting multiple ring tones and types of alerts. To adjust these settings, follow these instructions. Ring Tone 1. Press [Menu] to access the main menu. 2. Select 4: Ring/Alert. 3. Select 1: Ring Tone. 4. Use the up/down arrows ( / ) to select the desired ring tone and press [Store] to save. Ring Volume 1. Press [Menu] to access the main menu. 2. Select 4: Ring/Alert. 3. Select 2: Ring Volume. 4.
Phone Settings Banner The banner is the text displayed on the screen when the phone is not in use. This can be used to personalize your phone. To set your phone’s banner display: 1. Press [Menu] to access the main menu. 2. Select 5: Phone Settings. 3. Select 1: Banner. 4. Use your keypad to enter your desired banner and press [Store] to save. LCD Contrast 1. Press [Menu] to access the main menu. 2. Select 5: Phone Settings. 3. Select 2: LCD Contrast. 4.
Change Language Displayed On LCD The SX6P is capable of displaying multiple languages on the LCD screen. 1. Press [Menu] to access the main menu. 2. Select 5: Phone Settings. 3. Select 7: Language. 4. Select the desired setting and press [Store] to save. Dial Tone Type Your SX6P can produce the corresponding dial tones for phone systems in several countries. To select a regional dial tone type: 1. Press [Menu] to access the main menu. 2. Select 5: Phone Settings. 3. Select 8: Dial Tone Type. 4.
Security Change Code The lock code is a 4-digit password used to prevent unauthorized access to the phone. This setting allows you to change your phone’s lock code. The default lock code is 0000. Note: The phone’s default lock code is 0000. To change your phone’s lock code: 1. Press [Menu] to access the main menu. 2. Select 7: Security. 3. Enter the current lock code. (The default lock code is 0000.) 4. Select 1: Change Code. 5. Enter your new lock code and press [Store] to save the new setting.
Reset Phone This setting is used to reset the SX6P’s settings to the user default values. 1. Press [Menu] to access the main menu. 2. Select 7: Security. 3. Enter the current lock code. 4. Select 5: Reset Phone. 5. Select RESET and press [Store] to save. Hotline 1. Press [Menu] to access the main menu. 2. Select 7: Security. 3. Enter the current lock code. 4. Select 6: Hot Line. 5. Select Enable (followed by phone number to dial automatically) or Disable and press [Store].
BONDING AN SX6P TO A RUIM You can bond an SX6P to the RUIM that is inserted in it. Once an SX6P has been bonded to a RUIM, the SX6P will not operate normally with any other RUIM installed in it. It will reject incoming calls and permit only emergency outgoing calls. The same holds true for any other SX6P the bonded RUIM is installed into; it will not operate normally. Bonding an SX6P to a RUIM can only be done once. It cannot be undone by the user.
SX6P Troubleshooting Telephone Service is Not Working (Cannot place or receive calls) • Make sure the SX6P powered on properly. • Make sure any equipment that is externally connected to the SX6P is correctly connected. • Test any externally connected equipment on a known system to verify operation. • Make sure the antenna is properly connected. • Make sure your wireless account is activated and service is established.
Conformance Statements FCC Part 15 Class B Compliance This Phonecell® SX6P model has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. Changes or modifications not expressly approved by Telular Corporation will void your authority to operate the equipment per FCC part 15 paragraph 15.21.These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Driving Check the laws and regulations on the use of cellular products in the areas where you drive. Some jurisdictions prohibit your using a cellular device while driving a vehicle. Even if your jurisdiction does not have such a law, we strongly suggest that, for safety reasons, the driver use extreme caution when operating the cellular device while the vehicle is in motion. Always obey the law. Electronic Devices Most modern electronic equipment is shielded from RF energy.
Patents: Telular Corporation products are protected and manufactured under one or more of the following U.S. patents and related international patents and patents pending relating thereto: 4,658,096; 4,737,975; 4,775,997; 4,868,519; 4,922,517; 5,134,651; 5,361,297; 5,469,494; 5,046,085; 5,715,296. Trademarks: Telular Corporation owns the following registered trademarks: TELULAR and design, TELULAR, CELJACK, MAXJACK, TELCEL, HEXAGON LOGO, PHONECELL, CELSERV, TELGUARD, CPX, and AXCELL.
647 North Lakeview Parkway Vernon Hills, Illinois 60061, USA Tel: 847-247-9400 • Fax: 847-247-0021 E-mail: support@telular.com http://www.telular.com ©2005 Telular Corporation, all rights reserved.
