Instructions

ManualsBrandsTEMPMATE ManualsTemperature GaugesIR thermometer .-IR30 Display (thermometer) 50:1 -30 up

CDE FG

I J K

Diagram illustrating the D/S targeting ratio

D:S=50:1

19mm@

300mm

18mm@

900mm

42mm@

1500mm

0.8"@

12"

0.7"@

36"

1.7"@

60"

A. Introduction

G. Maintenence

H. Specification

B. Warning & Cautions

21 3

5 64

D. Emissivity

F. LCD display & buttons

E. Operation

2. ：

(figure 2)

Diagram description

C. Distance to spot size

This infrared thermometer is used for measuring the tem-

perature of the object's surface, which is applicable for va-

rious hot, hazardous or hard-toreach objects without contact

safe and quickly.

This unit consist of Optics, Temperature Sensor Signal

amplifier, Processing circuit and LCD Display. The Optics

collected the infrared energy emitted by object and focus

onto the Sensor. Then the sensor translates the energy into

an electricity signal. This signal will be turned out to be digital

shown on the LCD after the signal amplifier and processing

circuit.

Equipped with USB data export function, this

product is surely to be a great help to your work.

1. Warning:

To avoid the potential situation may cause harm or dam-

age to people, please pay attention to the following items:

1) . Do not point laser directly at eye or indirectly off reflective

surfaces.

2) . The unit cannot measure through transparent surfaces

such as glass or plastic. It will measure the surface tem-

perature of these materials instead.

3) . Steam, dust, smoke, or other particles can prevent acc-

urate measurement by obstructing by the units optics.

2. Cautions:

Infrared thermometer should be protected for the

following:

1). EMF (electro-magnetic fields) from arc welders,

induction heaters.

2). Thermal shock (cause by large or abrupt ambient

temperature changes allow 30 minutes for unit to

stabilize before use).

3). Do not leave the unit on or near objects of high

temperature.

Emissivity: Most organic materials and painted or

oxidized surfaces have an emissivity of 0.95(preset in

the unit). Inaccurate readings will result from measuring

shiny or polished metal surfaces. To compensate for

this, adjust the units emissivity reading or cover the

surface to be measured with masking tape or flat black

paint. Measure the tape or painted surface when the

tape or painted reach the same temperature as the

material underneath.

1. When take measurement, pay attention to the Distance to

Spot Size. As the Distance (D) from the target surface

increases, the spot size (S) of the area measured by the

unit becomes larger.

The Distance to Spot size of the unit is 20:1.

This unit is equipped with a laser, which is used for aiming.

2. Field of view:

Make sure the target is larger than the unit's spot size. The

smaller the target the closer measure distance. When

accuracy is critical, make sure the target is at least twice as

large as the spot size.

0.30

0.95

0.70

0.50

0.90

0.85

0.95

0.94

0.90

0.93

0.85

0.98

0.70

0.50

0.98

0.94

0.93

0.95

0.90

0.98

0.90

0.80

0.94

0.93

0.94

Emissivity

Marterial

Aluminum

Asbestos

Asphalt

Basalt

Brass

Brick

Carbon

Ceramic

Concrete

Copper

Dirt

Frozen food

Hot food

Glass(plate)

Ice

Iron

Lead

Limestone

Oil

Paint

Paper

Plastic

Rubber

Sand

Skin

Snow

Steel

Textiles

Water

Wood

1. Operating the unit：

1). Open the battery door and insert a 9V battery properly；

2). Pull the trigger to turn on the unit;

3). Aim at the target surface and pull the trigger, then temp-

erature will be shown on the LCD.

This unit is equipped with a laser, which is only used for

aiming.

2. Locating a Hot Spot：

To find a hot spot, aim the thermometer outside of interest,

then scan across with an up and down motion until you

locate the hot spot. (Figure 1)

Figure 1

1.LCD display:

A: Measuring reading

B: Measuring unit

C: Laser on icon

D: Backlight on icon

E: Battery power icon

F: Scanning icon

G: Data hold icon

H: Mode/emissivity indicator

I: Data storge / read icon

J: Low temperature alarm icon

K: High temperature alarm icon

(1) Trigger: Full screen display will last for one seconds

after turning on. And turn to display reading with

SCAN icon. Release the trigger, display reading

with HOLD icon. Built in auto power off in 20sec.

(2) Laser / back light button: when back light turn on,

any operations will remain back light for 10 sec.

LCD indicate on/off status.

(3)—(6) key functions: press 3 key, LCD subdisplay

blinks MAX-MIN-DIF-AVG-HAL-LAL-STO-EMS seg-

ment(only main display means normal measuring

mode) press 4 key to enter.

a. MAX: measuring maximum temperature

b. MIN: measuring minimum temperature

c. DIF: Basic on the reading before press 4 key,

compute the difference of current reading.

d. AVG: The average value of all measured in last 2

seconds

e. HAL: high temperature alarm--when selected HAL,

press 5 keys to set high temperature alarm trigger

and confirmed by pressing 4 key. When reading over

trigger, LCD display HI icon with BiBi audio sounds.

f. LAL: low temperature alarm--when selected LAL,

press 5 keys to set low temperature alarm trigger and

confirmed by pressing 4 key.

When reading over trigger, LCD display LOW icon

with BiBi audio sounds

g. STO: data storage--when selected STO, lock & DATA

& 1---indicator will shown when press 4 key. After

temperature read out press 6 key to store, then 2---

memory unit will be shown. There 80 groups memory

unit available. To recall the stored data in normal

measuring mode by pressing 6 key, remove all data

by pressing 6 keys for 3 seconds.

H. EMS: Emissivity setup-- press 5 key for emissivity

settings, press 4 key to save setup and back to

normal status.

1. Lens Cleaning:

Blow off loose particles using clean compressed air.

Gently brush remaining debris away with a moist cotton

swab. The swab may be moistened with water.

2. Case cleaning: Clean the case with a damp sponge/cloth

and mild soap.

Note:

1) Do not use solvent to clean plastic lens.

2) Do not submerge the unit in water.

MADE IN CHINA

SET

MODE

STO

CAL

Figure 2

Version：IR30-EN-00

Infrared thermometer

Instruction manual

GM11

D T

0 C ~ 11

0 C (

8 F ~ 2

2 F)

Accuracy

0~1650℃(32~3002℉) :±1.5℃(±2.7℉)

or±1.5%

-30~0℃(-22~32℉):±3℃ (±5℉)

Whichever is greater

Repeatability

1% of reading or 1℃

Response time

0.5~0.8 Sec, 95% response

8-14 um

Emissivity

0 ~40℃ (32 ~ 104℉)

-20 ~ 60℃ (-4~140℉)

Power

9V Alkaline or NiCd battery

Non-laser mode: 22 hrs;

Laser Models:12 hrs

50:1

Spectral response

Operating Humidity

Storage Temperature

Typical battery life

(Alkaline)

Distance to Spot size

Weight

Dimension

-30~1650℃ (-22~3002℉)

Temperature range

141*60*200mm

270g

Operating Temperature

10~95%RH non-condensing，

up to 30℃(86℉)

Resolution

0.1℃ or 0.1℉

0.10~1.00 Adjustable (0.95 Preset)

(7) Clesius / Fahrenheit switch: Please open battery

and push the slide switch for convertsion.

MODEL:IR30

D T

0 C ~ 1

0 C (

22 F ~ 30

2 F

)

-I

R30