Users Manual

Dark blue: Switched off.
Solid orange: Disconnected from a 2.4 GHz
Wi-Fi network.
Solid blue: Connected to a 2.4 GHz Wi-Fi
network and switched on.
Blinking blue: Connecting to a 2.4 GHz
Wi-Fi network.
On/Off: Press the button once.
Reset: Hold down the button for about 5
seconds to 8 seconds and release it when
the LED indicator blinks orange. The Smart
Wi-Fi Switch is reset successfully. Follow
this guide to configure it again.
Blinking orange: Initializing and starting.
LED
indicator
Button
Step 3: Install the Smart Wi-Fi Switch
①. Match the wires of the Smart Wi-Fi Switch with those in
the wall box according the wire labels, and secure them
using the wire nuts.
In the wall box with Load wire
Secure the Neutral wire, Ground wire, Line wire,
Load wires and Traveler wire from Smart Wi-Fi
Switch and the wall box correspondingly.
④. Install the wall plate.
②. Gently fold all wires back into the wall box and line up
the Smart Wi-Fi Switch with the mounting holes.
Secure it with included screws.
③. Turn main power ON at the circuit breaker. Verify that
the light can be turned on or off by pressing the Smart
Wi-Fi Switch.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road,
Nanshan District, Shenzhen, China. 518052
USA hotline: [phone]
Toll Free: 7 x 24 hours
Canada hotline: [phone]
Toll Free: Mon - Fri 9 am - 6 pm PST
Hong Kong hotline: [phone]
Global hotline: [phone] (China Time Zone)
Website: www.tendacn.com
E-mail: [e-mail]
Configure the device
1. Download the Tenda Beli App onto your mobile Wi-Fi-enabled
device, such as a smart phone, by searching for Tenda Beli in the
App Store or Google Play or by scanning the QR code.
2. Follow the instructions in the App to add your Smart Wi-Fi
Switch.
GET IT ON
Download on the
or
Tenda Beli
QR code
Tips:
• The Smart Wi-Fi Switch only supports 2.4 GHz Wi-Fi network.
• The default SSID (Wi-Fi name) of the Smart Wi-Fi Switch is
Tenda_Smart Switch_XXXX. XXXX indicates the last four
characters of its MAC address which can be found on the device.
Tips:
If the light is not on, try the following solutions.
• Confirm that the power is on.
• Check that the wire match is correct.
• If the problem persists, please consult an electrician.
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
This equipment should be installed and operated with minimum distance
20cm between the device and your body.
Caution:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Operating frequency: 2412-2462MHz
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
(2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be
handled pursuant to European directive 2012/19/EU in order to be recycled
or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or electronic
equipment.
Operating Temperature: 0°C～40°C（32°F～104°F）
Operating Humidity: (10％～90％)RH, non-condensing
FAQ
Q2: What devices can I control with the Smart Wi-Fi Switch?
A2: You can control bedside lamp, LED lamp, ceiling lamp, and any other lamps
in your home whose rated power does not exceed the maximum power
(450W) of the Smart Wi-Fi Switch.
Q1: What should I do when I failed to control the Smart Wi-Fi Switch After
adding it on the Tenda Beli App?
If the LED indicator of the Smart Wi-Fi Light Switch lights solid blue:
- Check whether the router is connected to the internet successfully.
If the LED indicator of the Smart Wi-Fi Light Switch lights solid orange:
- Check whether the Wi-Fi network of your wireless router is enabled. If not,
enable it.
- Check whether the Wi-Fi name or password of your wireless router is
changed. If so, reset the Smart Wi-Fi Switch, and re-configure it using the
Tenda Beli App.
Reset method: Hold down the button for about 5 seconds to 8 seconds and
release it when the LED indicator blinks orange.
A1: Try the following solutions:
Q4: If Line and Load are both black, how should I distinguish them?
- The Load wire is usually coming from the top of the box. The line wire is
usually coming from the bottom of the box.
- Before removing the switch, test each wire with a voltage tester.
NOTE: Risk of electric shock. DO NOT touch any wires during this process
and TURN OFF THE POWER before continuing the installation.
(1) Very carefully, press the voltage pen against each wire.
(2) The wire that causes the pen to glow red is the line wire.
(3) The wire that does not cause the pen to glow red is the Load wire.
A4: Try the following solutions:
Q3: How to control the Smart Wi-Fi Switch withvoice-activated devices,
such as Amazon Alexa or Google Assistant?
A3: In your Tenda Beli App, tap the Smart Wi-Fi Switch in the Device page,
then > (for Amazon Alexa) or (for Google Assistant) to get
the help.
Install the device
Step 1: TURN OFF THE POWER
①. Turn off the circuit breaker of your light switch.
②. Make sure power is off by turning your light switch on
and off a few times.
Note:
• A certain amount of electrical knowledge is required to install a
Smart Wi-Fi Switch. If you are not comfortable with basic
electrical wiring, please consult an electrician.
• You may need a screwdriver, pliers, wire strippers and a voltage
detector for the installation. Please prepare them in advance.
• This product is for indoor dry location use only.
• If you do not have neutral wire at home, the Smart Wi-Fi Switch
is not applicable.
• This Smart Wi-Fi Switch 3-way can be used with our Smart
Wi-Fi Switch 3-Way, or with ordinary non-smart 3-way switch.
OFF
ON
Get to know Smart Wi-Fi Switch
LED indicator
Button
Load wire
Ground wire
Traveler wire
Line wire
Neutral wire
Tra
N L L1 G
Step 2: Remove the old switch
①. Remove the screws that secure your old wall plate.
②. Verify that no electricity is going through the wire using
the voltage detector.
③. Remove the screws securing your old switch to the wall box.
④. Pull the switch out gently but do not disconnect the wires yet.
⑤. In the wall box, identify the Neutral, Ground, Line, Load (if
any) and Traveler wire, then label them.
⑥. Disconnect all wires from the old switch, and make sure not to
remove any of the wire labels.
Tips:
If your line and load wire are both black, refer to Q4 in FAQ.
Tips:
If you want to replace both old 3-way switches, please repeat
Step 1 and Step 2 to remove the other old switch.
Tips:
If you want to replace only one old 3-way switch, please
replace the old 3-way switch installed in the wall box
with load wire.
Smart Wi-Fi Light Switch 3-Way
SS6
Quick Installation Guide
Package contents
Smart Wi-Fi Light Switch 3-Way ×1
Wall plate ×1
Wire label ×1
Wire nut ×5
Screw ×2
Quick installation guide ×1
For product or function details, please go to www.tendacn.com to
download the user guide.
Copyright
© 2020 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
is a registered trademark legally held by Shenzhen Tenda
Technology Co., Ltd. Other brand and product names mentioned
herein are trademarks or registered trademarks of their respective
holders. Specifications are subject to change without notice.
Ground
Neutral
Line
(Supply In)
Load
(Out to Light)
Usually black
Usually red or black
Usually white or grey
Traveler
Usually blue or yellow
Usually green or copper
In the wall box without Load wire
Secure the Neutral wire, Ground wire and Line wire
from Smart Wi-Fi Switch and the wall box
correspondingly.
Secure the Load wire from the Smart Wi-Fi Switch to
the Traveler wire coming from the wall box.
N
L
L1
G
Tra
Traveler
Line
(Supply In)
Neutral
Load
(Out to Light)
Ground
Smart Wi-Fi Light Switch 3-Way
N
L
L1
G
Tra
Traveler
Line
(Supply In)
Neutral
Ground
Smart Wi-Fi Light Switch 3-Way
Circuit breaker
Circuit breaker