W300D Wireless-N ADSL2+ Router 1
W300D Wireless-N ADSL2+ Router Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co.
W300D Wireless-N ADSL2+ Router Content Chapter 1：Product Overview ...............................1 1.1 Product Introduction...................................1 1.2 Product Features........................................2 1.3 Package Contents ......................................4 Chapter 2：Getting to Know the Router .................5 2.1 Rear Panel and Port Description ...................5 2.2 Front Panel and LED Description...................6 2.3 Hardware Installation .................................
W300D Wireless-N ADSL2+ Router 6.2.3 WPA2-Personal .................................. 39 6.2.4 WPA-Enterprise.................................. 40 6.2.5 WPA2-Enterprise................................ 41 6.2.6 802.1X Authentication ........................ 42 6.3 WPS Setting............................................ 44 6.4 WDS Setting ........................................... 46 6.5 Advanced Wireless Setting ........................ 48 6.6 Wireless Access Control ............................ 50 6.
W300D Wireless-N ADSL2+ Router Chapter 12: System Tools .................................. 82 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 Time Setting.......................................... 82 DDNS ................................................... 84 Backup/Restore Setting........................... 85 Firmware Upgrade .................................. 87 Restore to Factory Default Settings ........... 89 Reboot ................................................. 90 Password Change ........................
W300D Wireless-N ADSL2+ Router Chapter 1：Product Overview 1.1 Product Introduction W300D ADSL2+ 300M Wireless Broadband Router provides up to 24Mbps downstream rate and 1Mbps upstream rate, which integrates ADSL2+ Modem, wireless router, four-port LAN switch and firewall in one. W300D utilizes advanced MIMO technology and increases over 8 times of transmission range of ordinary 802.11g IEEE802.11n (Draft products. 2.0) Compatible and with IEEE802.
W300D Wireless-N ADSL2+ Router WMM function can make your voice and video smoother. Powerful and exquisite, it is the best choice for SOHOs and small-sized enterprises to share the wireless network. 1.2 Product Features Integrates ADSL2+ Modem, wireless router, four-port LAN switch and firewall Complies with IEEE802.11n (Draft 2.0), compatible with IEEE802.11b and IEEE802.11g standards MIMO technology utilizes reflection signals to increase 8 times transmission distance of original 802.
W300D Wireless-N ADSL2+ Router Permanent Virtual Circuits standard Setup Wizard support for fast and easy configurations WPS (PBC and PIN) encryption method to free you from remembering long passwords Supports remote/local Web management Supports wireless Roaming technology to ensure high-efficient wireless connections Supports wireless SSID stealth mode and MAC address access control Supports Auto MDI/MDIX Provides system log to record the status of the router Supports MAC ad
W300D Wireless-N ADSL2+ Router Supports auto wireless channel selection Supports WDS function (Wireless Distribution System) 1.3 Package Contents One W300D Wireless-N ADSL2+ Broadband Router One CD-ROM (User Guide, Setup Wizard, etc.
W300D Wireless-N ADSL2+ Router Chapter 2 ： Getting to Know the Router 2.1 Rear Panel and Port Description Rear Panel View： Rear Panel Description： Rear Panel Interface Description LAN(1-4) Connect with your computer’s NIC or uplink to hub or switch.
W300D Wireless-N ADSL2+ Router RESET/WPS DSL POWER Note: press this button for 7 seconds, the settings you configured will be deleted and restored to factory default setting. If press for 1 second, the WPS (PBC) is enabled. Connect with DSL telephone line. For AC12/1.0A connection 2.
W300D Wireless-N ADSL2+ Router LED Indicator State POWER Always ON SYS Blinking DSL Description Indicates it is powered on well. Indicates the system works on well. Indicates it is connected with DSL termination well. Indicates it is going on connection negotiation Indicates the wireless module works well. Indicates it is transmitting and/or receiving data. Indicates it is connected well. Indicates the router’s LAN port is transmitting and/or receiving data.
W300D Wireless-N ADSL2+ Router 1. Connect to the Router’s DSL port with telephone line. 2. Use the delivery-attached power adapter to power the Router.
W300D Wireless-N ADSL2+ Router 3. Connect the LAN port of the Router to the network adapter of your computer with one cable. IMPORTANT: Please use the included power adapter. Use of a different power adapter could cause damage and void the warranty for this product.
W300D Wireless-N ADSL2+ Router Chapter 3：Getting to Connect the Broadband Router For easy and fast configuration, the following steps for network configuration are required. 3.1 How to Set the Network Configurations for My Computer 1. Right click “My Network Places” and select “Properties”.
W300D Wireless-N ADSL2+ Router 2. Right click “Local Area Network Connection” and select “Properties”. 3. Select “Internet Protocol (TCP/IP)” and click “Properties”.
W300D Wireless-N ADSL2+ Router 4. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click “OK” to save the configurations. Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as shown right. Of course, you need to input the DNS server address provided by your ISP. Otherwise, you can use the Router’s default gateway as the DNS proxy server. Click “OK” to save the configurations.
W300D Wireless-N ADSL2+ Router 13
W300D Wireless-N ADSL2+ Router 3.2 How to Check the Network Connection 1. Select Start”—”Programs”—“Accessories” —“Command Prompt”. 2. Input the “ping 192.168.0.1” and press “Enter”. If the screen displays as the right figure, it means your PC is connected to your router successfully. If not, please make sure the hardware installation and network adapter are OK.
W300D Wireless-N ADSL2+ Router 3.3 How to Access the Configuration Utility Web-based 1. To access the Router’s Web-based Utility, launch a web browser such as Internet Explorer or Firefox and enter the Router’s default IP address, http://192.168.0.1. Press “Enter”. 2、input the “admin” in both User Name and Password. Click “OK”.
W300D Wireless-N ADSL2+ Router 3、If you enter the correct user name and password, the following page appears.
W300D Wireless-N ADSL2+ Router Chapter 4：DSL Setting This section deals with how to configure the Router’s basic setting via Web interface. 4.1 DSL Setting This guide can assist you to configure the Router’s connection mode and basic parameters fast. The Router supports five common connection modes (Bridging, MER, IpoA, PPPoE, PPPoA). Select one according your actual requirements.
W300D Wireless-N ADSL2+ Router After the setting is completed, please click “Apply”. The device will reboot and the settings will go into effect.
W300D Wireless-N ADSL2+ Router Network Status： Connection State： To check if it is connected well with ISP Connection Mode： Show the connection mode for Internet access. WAN IP、Subnet Mask、Gateway、Primary DNS Server、Secondary DNS Server： After the Router connects well with ISP, the TCP/IP parameters are obtained. Or you can specify by manual. Connection Time： The communication time for the Router and ISP DSL State： Connection State： Show If the DSL is connected well. Virtual Circuit： Show the VPI/VCI value.
W300D Wireless-N ADSL2+ Router System Date： The system date of the Router Client： The client number connected with the device Connection Mode 1： Bridging If you want to configure the device’s connection mode as Bridging, please select “Bridging” in the Encapsulation field under Internet Connection Mode. Region selection: Country, City, Provider. If the city or ISP is not listed in the drop-down menu, you can enter the VPI and VCI value.
W300D Wireless-N ADSL2+ Router Connection Mode 2：MER If your ISP provides your connection way as Dynamic IP (it means you obtain different IP address each time to access the Internet), select “MER” in “Encapsulation” field and “Auto obtain IP address” in “WAN IP setting”.
W300D Wireless-N ADSL2+ Router Region selection: Country, City, Provider. If the city or ISP is not listed in the drop-down menu, you can enter the VPI and VCI value. “Encapsulation Mode”, “DSL Modulation” are suggested to select the default value. If there is something wrong, you can inquire your local ISP.
W300D Wireless-N ADSL2+ Router Connection Mode 3：IPoA If your ISP provides your connection way as IPoA, select “IPoA” in “Encapsulation” field. You need input the “IP address”, “Subnet Mask”, “Default Gateway”, “DNS Server”, and “Secondary DNS Server” into the corresponding fields.
W300D Wireless-N ADSL2+ Router Region selection: Country, City, Provider. If the city or ISP is not listed in the drop-down menu, you can enter the VPI and VCI value. “Encapsulation Mode”, “DSL Modulation” are suggested to select the default value. If there is something wrong, you can inquire your local ISP. Other Settings: MTU: Maximum Transmission Unit. The default value is 1492. Don’t modify the default value unless necessary.
W300D Wireless-N ADSL2+ Router Connection Mode 4： PPPoE If your ISP provides your connection way as PPPoE, select “PPPoE” in “Encapsulation” field. You need input your user name and password provided by ISP or network administrator in “PPPoE Setting” corresponding fields.
W300D Wireless-N ADSL2+ Router Region selection: Country, City, Provider. If the city or ISP is not listed in the drop-down menu, you can enter the VPI and VCI value. “Encapsulation Mode”, “DSL Modulation” are suggested to select the default value. If there is something wrong, you can inquire your local ISP. Other Settings: MTU: Maximum Transmission Unit. The default value is 1492. Don’t modify the default value unless necessary. Service Name: The current PPPoE connection name.
W300D Wireless-N ADSL2+ Router Note: Only you have set the current time in Time Setting, then “Connect on Fixed Time” can be used. Connection Mode 5： PPPoA If your ISP provides your connection way as PPPoA, select “PPPoA” in “Encapsulation” field. You need input your user name and password provided by ISP or network administrator in corresponding fields.
W300D Wireless-N ADSL2+ Router Dial-up Timeout： During a fixed time, if the auto dial-up fails, the dial-up will stop. Ideal Timeout： If there is no communication in the fixed time, the link will be disconnected. Region selection: Country, City, Provider. If the city or ISP is not listed in the drop-down menu, you can enter the VPI and VCI value. “Encapsulation Mode”, “DSL Modulation” are suggested to select the default value. If there is something wrong, you can inquire your local ISP.
W300D Wireless-N ADSL2+ Router Chapter 5：Advanced Setting This section will guide you to configure the Router’s advanced settings, including LAN setting, MAC address clone and DNS setting. 5.1 LAN Setting This page focuses on how to configure LAN Setting. MAC Address： The Router’s physical MAC address as seen on your local network, which is unchangeable IP Address： The Router’s LAN IP address (not your PC’s IP address).
W300D Wireless-N ADSL2+ Router Note： If you have changed the IP address, you need use the new IP address to login the Router’s Web interface next time, and the default gateway of all computers in the LAN must be via this IP address to access the Internet. Subnet Mask： The Router’s subnet mask for measurement of the network size.255.255.255.0 is the default value. 5.2 MAC Address Clone Some ISPs require end-user's MAC address to access their network.
W300D Wireless-N ADSL2+ Router MAC Address： The MAC address to be registered with your Internet service provider. Clone MAC Address： Register your PC's MAC address. Restore Default MAC Address： Restore the address.
W300D Wireless-N ADSL2+ Router 5.3 DNS Settings DNS is short for Domain Name System (or Service), an Internet service that translate domain names into IP addresses which are provided by your Internet Service Provider. Please consult your Internet Service Provider for details if you do not have them. DNS Setting： Click the checkbox to enable the DNS server. The Router’s DHCP server then will assign the DNS for client’s request. Primary DNS Address: Enter the necessary address provided by your ISP.
W300D Wireless-N ADSL2+ Router Chapter 6：Wireless Settings This section mainly deals with the wireless settings, including Basic Settings, Security Setting, Access Control and Advanced Settings. 6.1 Basic Setting Network Mode: Select one mode from the following: 802.11b/g mixed, 802.11b, 802.11g and 802.11b/g/n mixed.
W300D Wireless-N ADSL2+ Router name of the wireless network. This device has two SSIDs and the main SSID is necessary. Minor SSID: Minor Service Set Identifier. It is optional. Broadcast (SSID)： Select “enable” to enable the device's SSID to be visible by wireless clients. AP Isolation： When this feature is enabled, each of your wireless clients will be in its own virtual network and will not be able to communicate with each other.
W300D Wireless-N ADSL2+ Router MBSSID AP Isolation： When it is enabled, the wireless clients connected with AP can not access each other to isolate completely access control in WLAN. BSSID： Business Service Set Identifier of wireless network. In IEEE802.11, BSSID is the MAC address of wireless access point. Channel： Specify the effective channel (from 1 to 14) of the wireless network. Extension Channel： To increase data throughput of wireless network, the extension channel range is used in 11n mode.
W300D Wireless-N ADSL2+ Router 6.2 Wireless Security Settings This page is used to configure the device’s network security setting. Here presents the common six encryption methods, WPA-personal, including WPA-enterprise, Mixed WEP, WPA2-personal, WPA2- enterprise, etc. It is recommended to use WPA2-personal encryption method. 6.2.1 Mixed WEP WEP (Wired Equivalent Privacy), a basic encryption method, usually encrypts wireless data using a series of digital keys (64 bits or 128 bits in length).
W300D Wireless-N ADSL2+ Router SSID Choice： Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. Security Mode： From the drop-down menu select the corresponding security encryption modes. WEP Key： Set the WEP key with the format of ASCII and Hex. Key Description： Enter ASCII code (5 or 13 ASCII characters. Illegal character as “/” is not allowed.) or 10/26 hex characters. Default Key： Select one key from the four configured keys as the current available one.
W300D Wireless-N ADSL2+ Router 6.2.2 WPA- Personal WPA (Wi-Fi Protected Access), a Wi-Fi standard, is a more recent wireless encryption scheme, designed to improve the security features of WEP. Select “WPA-personal” from the drop-down menu to enter the following window: WPA Algorithms: Select one encryption type, AES (AES is stronger than TKIP.) or TKIP. Pass Phrase: Enter the key which must have 8-63 ASCII characters. Key Renewal Interval: Enter the key renewal period.
W300D Wireless-N ADSL2+ Router 6.2.3 WPA2-Personal WPA2 (Wi-Fi Protected Access version 2), It's more secure than Wired Equivalent Privacy (WEP) and easy to set up. WPA Algorithms: Select key Algorithms such as TKIP, AES and TKIP&AES. Pass Phrase: Enter the key which must have 8-63 ASCII characters. Key Renewal Interval: Enter the key renewal period. It is to tell the Router how often to change the keys.
W300D Wireless-N ADSL2+ Router 6.2.4 WPA-Enterprise This security mode is used when a RADIUS server is connected to the device. Select “WPA-enterprise” from the drop-down menu to enter the following window: Radius IP Address： Enter the IP address of the Radius server. Radius Port： Enter the authentication port of the Radius server. The default is 1812. Shared Key： Enter the shared key for authentication server with 8~63 ASCII characters.
W300D Wireless-N ADSL2+ Router 6.2.5 WPA2-Enterprise This security mode is also used when a RADIUS server is connected to the Router. Radius IP Address： Enter the IP address of the Radius server. Radius Port： Enter the authentication port of the Radius server. The default is 1812. Shared Key： Enter the shared key for authentication server with 8~63 ASCII characters. Session Timeout： The authentication interval period between AP and authentication server. The default is 3600s.
W300D Wireless-N ADSL2+ Router 6.2.6 802.1X Authentication This security mode is used when a RADIUS server is connected to the device. 802.1x, a kind of Port-based authentication protocol, is an authentication type and strategy for users. The port can be either a physic port or logic port (such as VLAN). For wireless LAN users, a port is just a channel. The final purpose of 802.11x authentication is to check if the port can be used.
W300D Wireless-N ADSL2+ Router WEP： Click “Enable/Disable” to enable or disable the WEP algorithm. Radius IP Address： Enter the IP address of the Radius server. Radius Port： Enter the authentication port of the Radius server. The default is 1812. Shared Key： Enter the shared key for authentication server with 8~63 ASCII characters. Session Timeout： The authentication interval period between AP and authentication server. The default is 3600s.
W300D Wireless-N ADSL2+ Router 6.3 WPS Setting WPS (Wi-Fi Protected Setting) can be easy and quick to establish the connection between the wireless network clients and the Router through encrypted contents. The users only enter the PIN code to configure without selecting encryption method and entering secret keys by manual. WPS Setting： To enable or disable WPS function. The default is to disable.
W300D Wireless-N ADSL2+ Router PBC： Select the PBC or press the WPS button on the front panel of the device for one second (Press the button for one second and WPS indicator will be blinking for 2 minutes, which means the WPS is enabled. During the blinking time, you can enable another device to implement the WPS/PBC negotiation between them. At present, the WPS only supports up to 32 clients access. Two minutes later, the WPS indicator will be off. If more clients are added, repeat the above steps).
W300D Wireless-N ADSL2+ Router 6.4 WDS Setting WDS (Wireless Distribution System) can be used to expand your current wireless network coverage. The Router supports three modes: Lazy, Bridge and Repeater. Lazy： In this mode, the connected wireless device should be in Bridge or Repeater mode, and select the Router’s BSSID to implement wireless connection. Bridge： In this mode, you can connect two or more wired networks via wireless signals.
W300D Wireless-N ADSL2+ Router Repeater： In this mode, you need add the MAC address of the connecting device into the Router's AP MAC address table to amplify and repeat wireless signals. Encrypt Type: You can select WEP mode, TKIP mode, AES mode for security here. Key： Enter the encryption key for the connecting devices. AP MAC Address： Input the MAC address of the connected wireless device.
W300D Wireless-N ADSL2+ Router 6.5 Advanced Wireless Setting This section is to configure the advanced wireless setting of the Router, including the Radio Preamble, 802.11g/n Rate, Fragmentation Threshold, RTS Threshold, Beacon Period and DTIM Interval. BG Protection Mode： For 11b/g wireless client, it is easier to connect with 11n wireless device. The default is “Auto”.
W300D Wireless-N ADSL2+ Router from the drop-down menu. Here, default value is (1-2-5.5-11Mbps…). Beacon Interval： The frequency interval of the beacon, which is a packet broadcast by a router to synchronize a wireless network. The default value is 100 ms. It is recommended not to modify the default value. Fragment Threshold： The fragmentation threshold defines the maximum transmission packet size in bytes. The packet will be fragmented if the arrival is bigger than the threshold setting.
W300D Wireless-N ADSL2+ Router 6.6 Wireless Access Control To secure your wireless LAN, the wireless access control is actually based on the MAC address management. Select “Wireless Setting-Access Control” to popup the following window: MAC Address Filter： Enable/disable MAC address filter. Select “Off” to malfunction MAC address; “Block” to prevent the MAC addresses in the list from accessing the wireless network; “Allow” to allow the MAC address in the list to access the wireless network.
W300D Wireless-N ADSL2+ Router 6.7 Wireless Connection Status This page is to show the current wireless access status. Click “Refresh” to update the wireless connection information. MAC Address： Shows the connecting PC’s MAC address. Bandwidth: Shows the channel bandwidth of the host to be connected.
W300D Wireless-N ADSL2+ Router Chapter 7：DHCP Server 7.1 DHCP Server Setting DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When you enable the DHCP Server, the DHCP Server will allocate automatically an unused IP address from the IP address pool to the requesting computer in premise of activating “Obtain an IP Address Automatically”. So specifying the starting and ending address of the IP Address pool is needed.
W300D Wireless-N ADSL2+ Router 7.2 DHCP Client List The Static IP assignment is to add one specific static IP address to the assigned MAC address. You can view the related information in the DHCP server list. IP Address: Enter one IP address for the computer on the LAN network. MAC Address: Enter the MAC address of the computer you want to assign the above IP address. Click “Add” to add the entry in the list. Hostname: The name of the computer which is added a new IP address.
W300D Wireless-N ADSL2+ Router Chapter 8：Virtual Server 8.1 Single Port Forwarding The Router can be configured as a virtual server on behalf of local services behind the LAN port. The given remote requests will be re-directed to the local servers via the virtual server. This section deals with the single port forwarding mainly. The Single Port Forwarding allows you to set up kinds of public services such as web servers, ftp, e-mail and other specialized Internet applications on your network.
W300D Wireless-N ADSL2+ Router External Port： This is the external port number for server or Internet application, for example, port 21 for ftp service. Internal Port: This is the port number of LAN computer set by the Router. The Internet traffic from the external port will forward to the internal port. For example, you can set the internal port NO.66 to act as the external port NO.21 for ftp service. IP Address: Enter the IP address of the PC where you want to set the applications.
W300D Wireless-N ADSL2+ Router add it by manual. Add: To add the well-know port to ID you selected. If the host with IP address 192.168.0.10 in the LAN provides Web service via port 80, and you want to forward this service to port 40, configure it as the following setting. NOTE: If you set the virtual server of the service port as 80, you must set the Web management port on Remote Web Management page to be any value except 80 such as 8080. Otherwise, there will be a conflict to disable the virtual server.
W300D Wireless-N ADSL2+ Router 8.2 Port Range Forwarding This section deals with the port range forwarding. The Port Range Forwarding allows you to set up a range of public services such as web servers, ftp, e-mail and other specialized Internet applications to an assigned IP address on your LAN. Start/End Port: Enter the start/end port number which ranges the External ports used to set the server or Internet applications. IP Address: Enter the IP address of the PC where you want to set the applications.
W300D Wireless-N ADSL2+ Router Protocol: Select the protocol (TCP/UDP/Both) for the application. Well-Known Service Port: Select the well-known services as DNS, FTP from the drop-down menu to add to the configured one above. Delete/Enable: Click to check it for corresponding operation. In Well-known Service Port, list the common ports, you can select one from them and add one ID number from the drop-down menu, click “Add” to add the port in the above table.
W300D Wireless-N ADSL2+ Router 8.3 Port Trigger Setting When internal clients have access to external server in the Internet for some application, the clients request to connect with severs, and the server will also ask to connect with client. But in the default setting, router will refuse to accept any request from WAN, which will bring communication halt. The port triggering is used to define triggering rules.
W300D Wireless-N ADSL2+ Router server with the range of 1～65535. Note that the low number first and two blanks can keep the same number if needed. External Port: The port range through which the external server send request traffics to internal clients with the range of 1～65535. Note that the low number first and two blanks can keep the same number if needed. Apply: Add: Apply: Cancel: To enable or disable the rule.
W300D Wireless-N ADSL2+ Router 8.4 ALG Service Setting ALG (Application Layer Gateway) in the context of computer networking, an ALG or application layer gateway consists of a security component that augments a firewall or NAT employed in a computer network. It allows customized NAT traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, Bit Torrent, SIP, RTSP, file transfer applications etc.
W300D Wireless-N ADSL2+ Router control traffic and open up port mappings (firewall pinhole) dynamically as required. Legitimate application data can thus be passed through the security checks of the firewall or NAT that would have otherwise restricted the traffic for not meeting its limited filter criteria.
W300D Wireless-N ADSL2+ Router 8.5 DMZ Host The DMZ function is to allow one computer in LAN to be exposed to the Internet for a special-purpose service as Internet gaming or videoconferencing. DMZ Host IP Address: The IP address of the computer you want to expose. Enable: Click the checkbox to enable the DMZ host. IMPORTANT: When enabled the DMZ host, the firewall settings of the function.
W300D Wireless-N ADSL2+ Router 8.6 UPnP Setting It supports latest Universal Plug and Play. This function goes into effect on Windows XP or Windows ME or this function would go into effect if you have installed software that supports UPnP. With the UPnP function, host in LAN can request the router to process some special port switching so as to enable host outside to visit the resources in the internal host. Enable UPnP: Click the checkbox to enable the UPnP.
W300D Wireless-N ADSL2+ Router Chapter 9: Traffic Control Traffic control is used to limit communication speed in the LAN and WAN. Up to 20 entries can be supported with the capability for at most 254 PCs' speed control, including for IP address range configuration. Enable Traffic Control: To enable or disable the internal IP bandwidth control. Interface: To limit the uploading and downloading bandwidth in WAN port.
W300D Wireless-N ADSL2+ Router HTTP service. IP Starting Address: The first IP address for traffic control. IP Ending Address: The last IP address for traffic control. Uploading/Downloading: To specify the traffic heading way for the selected IP addresses: uploading or downloading. Bandwidth: To specify the uploading/ downloading Min. /Max. traffic speed (KB/s), which can not exceed the WAN speed. Apply: To enable the current editing rule. If not, the rule will be disabled.
W300D Wireless-N ADSL2+ Router Chapter 10： Security Setting 10.1 Client Filter Settings To benefit your further management to the computers in the LAN, you can control some ports access to Internet by data packet filter function. Client Filter: Check to enable client filter.
W300D Wireless-N ADSL2+ Router Access Policy: Select one number from the drop-down menu. Enable: Check to enable the access policy. Clear the Policy: Click “Clear” button to clear all settings for the policy. Filter Mode: Click one radio button to enable or disable to access the Internet. Policy Name: Enter a name for the access policy selected. IP Start/End: Enter the starting/ending IP address. Port No.: Enter the port range based over the protocol for access policy.
W300D Wireless-N ADSL2+ Router 10.2 URL Filter In order to control the computer to have access to websites, you can use URL filtering to allow the computer to have access to certain websites at fixed time and forbids it having access to certain websites at fixed time. URL Filter: Check to enable URL filter. Access Policy: Select one number from the drop-down menu. Enable: Check to enable the access policy.
W300D Wireless-N ADSL2+ Router Filter Mode: Click one radio button to enable or disable to access the Internet. Policy Name: Enter a name for the access policy selected. Start/End IP: Enter the starting/ending IP address. URL Strings： Specify the text strings or keywords in the DNS. If any part strings of the URL contains these or words, the web page will not be accessible and display. Times： Select the time range of client filter. Days： Select the day(s) to run the access policy.
W300D Wireless-N ADSL2+ Router 10.3 MAC Address Filter In order to manage the computers in LAN better, you could control the computer’s access to Internet by MAC Address Filter. MAC Address Filter: Check to enable MAC address filter. Access Policy: Select one number from the drop-down menu. Enable: Check to enable the access policy.
W300D Wireless-N ADSL2+ Router Filter Mode: Click one radio button to enable or disable to access the Internet. Policy Name: Enter a name for the access policy selected. MAC Address: Enter the MAC address you want to run the access policy. Times: Select the time range of client filter. Days: Select the day(s) to run the access policy. Apply： Click to make the settings go into effect.
W300D Wireless-N ADSL2+ Router 10.4 Prevent Network Attack This section is to protect the internal network from exotic attack such as SYN Flooding attack, Smurf attack, LAND attack, etc. Once detecting the unknown attack, the Router will restrict its bandwidth automatically. The attacker’s IP address can be found from the “System Log”. Prevent Network Attack: Check to enable it for attack prevention.
W300D Wireless-N ADSL2+ Router 10.5 Remote Web Management This section is to allow the network administrator to manage the Router remotely. If you want to access the Router from outside the local network, please select the “Enable”. Enable: Port: Check to enable remote web management. The management port open to outside access. The default value is 80. WAN IP Address: Specify the range of the WAN IP address for remote management.
W300D Wireless-N ADSL2+ Router port (for example http://219.134.32.101: 8080) to implement remote login. If your WAN IP address starts and ends with 0.0.0.0, it means all hosts in WAN can implement remote Web management. If you change the WAN IP address as 218.88.93.33-218.88.93.35, then only the IP addresses as 218.88.93.33, 218.88.93.34 and 218.88.93.35 can access the Router. For example: If you want to configure the IP address 218.88.93.
W300D Wireless-N ADSL2+ Router 10.6 Local Web Management Local web management, the alternative to remote web management, is to allow the network administrator to manage the Router in LAN. Any PC in the LAN can access the Web management utility by default. So you can enter the specific MAC address of the LAN computer to function. Enable: Check to enable the local web management MAC1/2/3…: Enter the MAC addresses of LAN computers.
W300D Wireless-N ADSL2+ Router Note： 1. In the default state, this feature is not enabled. All computers in the LAN can login the Web. 2. For example, if you only allow the MAC address with 00:11:22:33:E4:F5 to access the Web, please set it as follows. 3. If you just check the frame to enable this feature and not to add any MAC address, all computers can not interface via Web.
W300D Wireless-N ADSL2+ Router 10.7 WAN Ping The ping test is to check the status of your internet connection. When disabling the test, the system will ignore the ping test from WAN. Ignore Ping from WAN: Check to ignore the ping request and give no reply.
W300D Wireless-N ADSL2+ Router Chapter 11: Routing Setting 11.1 Routing Table The main duty for a router is to look for a best path for every data frame, and transfer this data frame to a destination. So, it’s essential for the router to choose the best path, i.e. routing arithmetic. In order to finish this function, many transferring paths, i.e. routing table, are saved in the router, for choosing when needed.
W300D Wireless-N ADSL2+ Router 11.2 Static Routing This page is used to configure the Router’s static routing. Destination LAN IP: The address of the remote host with which you want to construct a static route. Subnet Mask: The network portion of the Destination LAN IP. Gateway: The gateway of the next hop, usually the Router or host’s IP address. Tip： Static Route is set by system administrator in advance. Usually, It would not be subjected to network structure’s change.
W300D Wireless-N ADSL2+ Router Note： 1. The gateway must keep the same segment with the Router’s LAN IP address. 2. If the destination IP address is one host’s IP address, the Subnet mask should be 255.255.255.255. 3. If the destination IP address is an IP address range, the subnet mask should match the IP address. For example, if the IP is 10.0.0.0, subnet mask should be 255.0.0.0; if the IP is 10.1.2.0, subnet mask should be 255.255.255.0.
W300D Wireless-N ADSL2+ Router Chapter 12: System Tools 12.1 Time Setting This section is to select the time zone for your location. If you turn off the Router, the settings for time disappear. However, the Router will automatically obtain the GMT time again once it has access to the Internet. Time Zone: Select your time zone from the drop-down menu. Customized time: Enter the time you customize.
W300D Wireless-N ADSL2+ Router Note： When the Router is powered off, the time setting will be lost. Before the Router will obtain GMT time automatically, you need connect with the Internet and obtain the GMT time, or set the time on this page first. Then the time in other features (e.g. firewall) can be go into effect.
W300D Wireless-N ADSL2+ Router 12.2 DDNS The DDNS (Dynamic Domain Name System) is supported in this router. It is to assign a fixed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind the Router. If you want to activate this function, please select “Enable” and a DDNS service provider to sign up. DDNS: Click the radio button to enable or disable the DDNS service.
W300D Wireless-N ADSL2+ Router Password: Enter the password you set. Domain Name: Enter the domain name which is optional. 12.3 Backup/Restore Setting The device provides backup/restore settings, so you need set a directory to keep these parameters. Backup Setting Click “Backup” button to back up the Router’s settings and select the path for save.
W300D Wireless-N ADSL2+ Router Restore Setting： Click “Browse” button to select the backup files. Click “Restore” button to restore previous settings.
W300D Wireless-N ADSL2+ Router 12.4 Firmware Upgrade The Router provides the firmware upgrade by clicking the “Upgrade” after browsing the firmware upgrade packet which you can download from www.tenda.cn. After the upgrade is completed, the Router will reboot automatically. Through upgrading the Router’s software, you can gain more stable performance and value-added features. You can download the latest upgrade file and TFTP Server from the website www.tenda.cn.
W300D Wireless-N ADSL2+ Router When your computer connects with the Router’s LAN port, and obtain the IP address assigned by the Router, please run the TFTP Server, and keep the “Firmware File Name” same with the upgrade file name. Click “Upgrade” to start the firmware upgrading. IMPORTANT: Do not power off the system during the firmware upgrade to avoid damaging the device. The Router will reboot after the upgrade.
W300D Wireless-N ADSL2+ Router 12.5 Restore to Factory Default Settings This button is to reset all settings to the default values. It means the Router will lose all the settings you have set. So please Note down the related settings if necessary. Restore: Click this button to restore to default settings. Factory Default Settings: User Name: admin Password: admin IP Address: 192.168.0.1 Subnet Mask: 255.255.255.
W300D Wireless-N ADSL2+ Router 12.6 Reboot Rebooting the Router makes the settings configured go into effect or to set the Router again if setting failure happens. Reboot the router: Click this button to reboot the device.
W300D Wireless-N ADSL2+ Router 12.7 Password Change This section is to set a new user name and password to better secure your router and network. User Name: Enter a new user name for the device. Old Password: Enter the old password. New Password: Enter a new password. Re-enter to Confirm: Re-enter to confirm the new password. NOTE: It is highly recommended to change the password to secure your network and the Router.
W300D Wireless-N ADSL2+ Router 12.8 System Log The section is to view the system log. Click the “Refresh” to update the log. Click “Clear” to clear all shown information. If the log is over 150 records, it will clear them automatically. Refresh: Click this button to update the log. Clear: Click this button to clear the current shown log.
W300D Wireless-N ADSL2+ Router Appendix I: Glossary Access Point (AP): Any entity that has station functionality and provides access to the distribution services, via the wireless medium (WM) for associated stations.
W300D Wireless-N ADSL2+ Router keyboard).Make sure this setting is the same for all devices in your wireless network. WEP: Wired Equivalent method for Privacy secure (WEP) is wireless the data transmission. WEP adds data encryption to every single packet wireless network. transmitted in the The 40bit and 64bit encryption are the same because of out 64 bits, 40 bits are private. Conversely, 104 and 128 bit are the same. WEP uses a common KEY to encode the data.
W300D Wireless-N ADSL2+ Router is NOT recommend using. WPA/WPA2: A security protocol for wireless networks that builds on the basic foundations of WEP. It secures wireless data transmission by using a key similar to WEP, but the added strength of WPA is that the key changes dynamically. The changing key makes it much more difficult for a hacker to learn the key and gain access to the network.
W300D Wireless-N ADSL2+ Router megabytes) per second, and to send (upload) data at speeds of 128 kilobits per second. Thus the "Asymmetric" part of the acronym. ATM： ATM stands for Asynchronous Transfer Mode. A transmission protocol that breaks down user traffic into small fixed-sized cells, before reassembling them after transmission. During transmission, cells from different users are asynchronously intermixed, thereby maximizing network resources.
W300D Wireless-N ADSL2+ Router Hence the name, "virtual path identifier." The VPI is used in conjunction with the VCI, or virtual channel identifier. VCI： Stands for "Virtual Channel Identifier." The VCI indicates where an ATM cell is to travel over a network. The VCI within each ATM cell defines the fixed channel on which the packet of information should be sent. It is a 16-bit field, compared to the VPI, which is only 8 bits.
W300D Wireless-N ADSL2+ Router packets are transferred via ATM network. In this connection mode, user must have static IP address, subnet mask and other parameters. Lack of user name and password authentication, it can not implement network administration and QoS features, so this access way will not prevail any more. PPPoA： Short for Point-to-Point Protocol Asynchronous Transfer Mode (ATM). over PPPoA relies on two widely accepted standards: PPP and ATM.
W300D Wireless-N ADSL2+ Router PPPoE is a specification for connecting the users on an Ethernet to the Internet through a common broadband medium, such as a single DSL line, wireless device or cable modem. All the users over the Ethernet share a common connection, so the Ethernet principles supporting multiple users in a LAN combine with the principles of PPP, which apply to serial connections.
