1N Wireless Broadband Router 1
11N Wireless Broadband Router Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co.
11N Wireless Broadband Router CONTENTS Chapter 1: Introduction .......................................... 1 1.1 Product Features........................................... 2 1.2 Package Contents ......................................... 4 1.3 LED Indicator and Port Description .................. 4 Chapter 2 Hardware Installation .............................. 7 2.1 How to Install the Router ............................... 7 2.2 Network Application Plan................................
11N Wireless Broadband Router 6.2 Wireless Security Setting ..............................32 6.3 Advanced Settings .......................................40 6.4 WPS Settings ..............................................42 6.5 WDS Settings ..............................................44 6.6 Wireless Access Control ................................46 6.7 Connection Status........................................47 Chapter 7: DHCP Server ....................................... 48 7.1 DHCP Settings ............
11N Wireless Broadband Router 11.3 MAC Address Filter .....................................66 11.5 Remote Web Management ...........................68 11.6 Local Web Management...............................69 11.7 WAN Ping..................................................70 Chapter12 Routing Setting .................................... 71 12.1 Routing Table.............................................71 12.2 Static Routing............................................71 13.1 Time Settings ...................
11N Wireless Broadband Router Chapter 1: Introduction Thank you for purchasing Tenda 11N Wireless Broadband Router! W311R utilizes advanced MIMO technology and increases over 8 times transmission range of ordinary 802.11g products. Compatible with IEEE802.11n (Draft 4.0) and IEEE802.11g/b standards, it can provide up to 150Mbps stable transmission rate.
11N Wireless Broadband Router computer’s downloading speed is supported as well. Moreover, UPnP and WMM support can smooth your MSN voice better, and the included Setup Wizard on CD-ROM will be easy and fast for non-savvy users to install the device and access to the Internet. 1.
11N Wireless Broadband Router Ethernet LAN ports z Supports xDSL/Cable MODEM, static and dynamic IP in community networking z Supports remote/local Web management z Supports WMM to better smooth your voice and video z Supports SSID stealth mode and access control based over MAC address (up to 30 entries) z Supports Auto MDI/MDIX z Supports wireless Roaming technology for high-efficient wireless connections z Supports auto negotiation/manual mode for 802.11b/802.11g/802.
11N Wireless Broadband Router 1.2 Package Contents Please unpack the box and check the following items: One W311R 11N Wireless Broadband Router ¾ One Quick Installation Guide ¾ One Power Adapter ¾ One CD-ROM If any of listed items are missing or damaged, please contact the Tenda reseller from whom you purchased for replacement immediately. 1.
11N Wireless Broadband Router ¾ SYS When turns green, blinking indicates the system runs well. ¾ WPS When blinking, it indicates the device is negotiating with client in WPS mode. ¾ WLAN Wireless signal LED indicator. When turns green, blinking indicates the wireless function is enabled. ¾ LAN (4,3,2,1) Wired local network LED indicator. Always ON indicates it is connected with Ethernet device; blinking indicates the device is transmitting and/or receiving data. ¾ WAN Wide area network indicator.
N Wireless Broadband Router use the included 9V DC power adapter. ¾ WAN A 100Mbps Ethernet port, can be connected with MODEM, Switch, Router and other Ethernet device for Internet connecting to DSL MODEM, Cable MODEM and ISP. ¾ LAN (1, 2, 3, 4) 4 10/100Mbps Ethernet ports can be connected with Ethernet switch, Ethernet router and NIC card. ¾ RESET The system reset button.
11N Wireless Broadband Router Chapter 2 Hardware Installation 2.1 How to Install the Router After you unpack the box, please follow the steps below to connect. For better wireless performance, please put the device in the middle of wireless coverage area. Please use the included power adapter to power on the Router. IMPORTANT: Use of a different power adapter could cause damage and void the warranty for this product.
11N Wireless Broadband Router Please connect your broadband line provided by your ISP to the WAN port. Insert the included CD-ROM into the CD-ROM drive, double click the “Setup” icon and follow the instructions to complete the installation. Or you can enter the Router’s Web page to configure it. (More details please refer to Chapter 3.
11N Wireless Broadband Router 2.2 Network Application Plan Usually wireless LAN Network is deployed in a planned environment where each access point is located in a steady place with certain wireless coverage area for communication service. Generally speaking, it is in the center of the area to reduce “dead spot”.
11N Wireless Broadband Router Chapter 3 How to Login to the Router The chapter mainly presents how to enter the Router’s Web page. After you have finished the hardware installation, the following steps will assist you to set the network configurations for you computer. 3.1 How to Set the Network Configurations 1. On your computer desktop right click “My Network Places” and select “Properties”.
11N Wireless Broadband Router 2. Right click “Local Area Network Connection” and select “Properties”. 3 ． Select “Internet Protocol (TCP/IP)” and click “Properties”.
11N Wireless Broadband Router 4 ． Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click “OK” to save the configurations. Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as follows: IP Address: 192.168.0.XXX：(XXX is a number from 2~254) Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 Certainly you need to input the DNS server address provided by your ISP.
11N Wireless Broadband Router 3.2 Login to the Router 1．To access the Router’s Web-based interface, launch a web browser such as Internet Explorer or Firefox and enter the Router’s default http://192.168.0.1. Press “Enter”.
11N Wireless Broadband Router 2．Input the “admin” in both User Name and Password. Click “OK”. 3. If you enter the correct user name and password, the screen will be the next one.
11N Wireless Broadband Router Chapter 4: Quick Setup Guide This chapter deals with how to access the Internet quickly. Please follow this guide to connect your Router to the Internet. 4.1 Setup Wizard Here is the “Welcome to Setup Wizard” for configuring your Router quickly. Click “Next”. In this screen, select one mode of your Internet connection you use. If you are not clear, press the “Detect” button or contact your Internet Service Provider, and click “Next”.
11N Wireless Broadband Router ADSL Virtual Dial-up (Via PPPoE) Enter the Account and Password provided by your ISP, and click “Next”. For example： Dynamic IP (Via DHCP) If your connection mode is Dynamic IP, it means your IP address keeps changing every time you connect. You do not need to enter the information like other modes. Click “Next” and “Save” to finish the settings.
11N Wireless Broadband Router Static IP In this screen, fill the network address information from your ISP in the IP Address, Subnet Mask, Gateway and Primary DNS server fields and click “Next”. For example： ISP provides the following TCP/IP parameters as follows： IP Address：192.168.1.2 Subnet Mask：255.255.255.0 Gateway：192.168.1.1 Primary DNS Server：192.168.1.2 Alternate DNS Server：202.96.134.
11N Wireless Broadband Router Click “Save” to complete the setup wizard. The Router will record the settings you made. To activate the settings, it is recommended to select “Reboot the Router” from “System Tool” of the left menu. It is rebooting now, please wait for a few minutes and DO NOT power off it. Click the “System Status” in the left menu of the Web-based Utility to find out the current network and system information.
11N Wireless Broadband Router L2TP L2TP Server IP: Enter the Server IP provided by your ISP. User Name: Enter L2TP username. Password: Enter L2TP password. MTU: Maximum Transmission Unit, you may need to change it for optimal performance with your specific ISP. 1400 is the default MTU. Address Mode: Select “Static” if your ISP supplies you with the IP address, subnet mask, and gateway. In most cases, select Dynamic. IP Address: Enter the L2TP IP address supplied by your ISP.
11N Wireless Broadband Router PPTP PPTP Server IP: Enter the Server IP provided by your ISP. User Name: Enter PPTP username provided by your ISP. Password: Enter PPTP password provided by your ISP. Address Mode: Select “Static” if your ISP supplies you with the IP address, subnet mask, and gateway. In most cases, select Dynamic. IP Address: Enter the PPTP IP address supplied by your ISP. Subnet Mask: Enter the Subnet Mask supplied by your ISP.
11N Wireless Broadband Router Chapter 5: Advanced Settings 5.1 LAN Settings LAN Settings are for the basic TCP/IP parameters of LAN ports. ¾ MAC Address: The Router’s physical MAC address as seen on your local network, which is unchangeable. ¾ IP Address: The Router’s LAN IP addresses (not your PC’s IP address). 192.168.0.1 is the default value. ¾ Subnet Mask: It’s shown the Router’s subnet mask for measurement of the network size. 255.255.255.0 is the default value.
11N Wireless Broadband Router 5.2 WAN Settings After you have selected the ISP connection type in “Setup Wizard” and you want to modify the related settings, here you can modify and configure the settings in details. Virtual Dial-up（PPPoE） ¾ Connection Mode: Show your current connection mode. ¾ Account: Enter them provided by your ISP. ¾ Password: Enter them provided by your ISP. ¾ MTU: Maximum Transmission Unit. It is the size of largest datagram that can be sent over a network.
11N Wireless Broadband Router The default value is 1492. Do NOT modify it unless necessary. But if when some specific website or web application software can not be open or enabled, have a try to change the MTU value as 1450, 1400, etc. ¾ Service Name: characteristics It that is defined are applied as to a a set of PPPoE connection. Enter it if provided. Do NOT modify it unless necessary. ¾ AC Name: Enter it if provided. Do NOT modify it unless necessary.
11N Wireless Broadband Router Static IP If your connection mode, static IP is chosen, you can modify the following addressing information. ¾ IP Address: Here enter the WAN IP address provided by your ISP. ¾ Subnet Mask: Enter the WAN Subnet Mask here. ¾ Gateway: Enter the WAN Gateway here. ¾ Primary DNS Server: Enter the Primary DNS server provided by your ISP. ¾ Secondary DNS Server: Enter the secondary DNS.
11N Wireless Broadband Router 5.3 MAC Address Clone This page is for the Router’s MAC address to WAN. Some ISPs require end-user's MAC address to access their network. This feature copies the MAC address of your network device to the Router. ¾ MAC Address: The MAC address to be registered with your Internet service provider. ¾ Clone MAC Address: Register your PC's MAC address. ¾ Restore Default MAC Address: Restore to the default hardware MAC address.
11N Wireless Broadband Router 5.4 DNS Settings DNS is short for Domain Name System (or Service), an Internet service that translate domain names into IP addresses which are provided by your Internet Service Provider. Please consult your Internet Service Provider for details if you do not have them. ¾ DNS: Click the checkbox to enable the DNS server. The Router’s DHCP sever will answer the client’s requests and distribute DNS address.
11N Wireless Broadband Router 5.5 WAN Media Type In most cases, ISP provides wired WAN access (ADSL MODEM, Cable MODEM, etc.) and you only need to insert the line into the Router’s WAN port. Sometime, wireless WAN access type, more flexible and convenient, is also provided by some ISP. ¾ Wired WAN: In this type, WAN port should be connected by wired cable. This type is the device’s default option. ¾ Wireless WAN: When your ISP provides wireless access service, you can enable this WAN access type.
11N Wireless Broadband Router access to your ISP network. Click “Open Scanner’ to search the available SSID. ¾ MAC: Enter the MAC address of ISP wireless device. Click “Open Scanner’ to search the MAC address. ¾ Channel: Wireless device’s communication channel. Keep it the same channel with your ISP’s wireless device. Click “Open Scanner’ to search the available AP channel.
11N Wireless Broadband Router Chapter 6: Wireless Setting 6.1 Basic Settings ¾ Enable Wireless: Check to enable the Router’s wireless features; uncheck to disable it. ¾ Network Mode ： Select one mode from the following. The default is 11b/g/n mode.
11N Wireless Broadband Router 11b mode： Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11Mbps. 11g mode： Allow the 11g/11n-compliant client device to connect with the AP at the maximum speed of 54Mbps. 11b/g mode: Allow the 11b/g-compliant client device to connect with the AP with auto-negotiation speed, and 11n wireless client to connect the device with 11g speed. 11b/g/n mode：Allow 11b/g/n-compliant client device to connect with the AP with auto-negotiation speed.
11N Wireless Broadband Router via wireless adapter, and configure PC1 and PC2 in the same segment. After the feature is enabled, two PCs can not communicate and share network resource each other, but they can communicate with wireless clients connected with AP2. This feature is to isolate the communication of wireless clients connected with the same SSID. ¾ AP Isolation: One access control feature based on SSID.
11N Wireless Broadband Router ¾ Channel： Specify the effective channel (from 1 to 13\Auto) of the wireless network. ¾ Extension Channel：To increase data throughput of wireless network, the extension channel range is used in 11n mode. ¾ Channel Bandwidth ： Select the channel bandwidth to improve the wireless performance. When the network has 11b/g and 11n clients, you can select the 40M; when it is an 11n network, select 20/40M to improve its throughput. 6.
11N Wireless Broadband Router resources. Select Mixed WEP to enter the following window: ¾ Select SSID ： Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. ¾ Security Mode：From the drop-down menu select the corresponding security encryption modes. ¾ WEP Key1~4：Set the WEP key with the format of ASCII and Hex. You can enter ASCII code (5 or 13 ASCII characters. Illegal character as “/” is not allowed.) Or 10/26 hex characters.
11N Wireless Broadband Router 6.2.2 WPA-Personal WPA (Wi-Fi Protected Access), a Wi-Fi standard, is a more recent wireless encryption scheme, designed to improve the security features of WEP. It applies more powerful encryption types (such as TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard]) and can change the keys dynamically on every authorized wireless device.
11N Wireless Broadband Router 6.2.3 WPA2- Personal WPA2 (Wi-Fi Protected Access version 2) provides higher security than WEP (Wireless Equivalent Privacy) and WPA (Wi-Fi Protected Access). ¾ Select SSID ： Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. ¾ WPA Algorithms：Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode. ¾ Pass Phrase：Enter the encrypted characters with 8-63 ASCII characters.
11N Wireless Broadband Router 6.2.4 WPA- Enterprise This security mode is used when a RADIUS server is connected to the device. Select “WPA-Enterprise” from the drop-down menu to enter the following window: ¾ Select SSID ： Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. ¾ WPA Algorithms：Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode. ¾ Key Renewal Interval ： Set the key’s renewal period.
11N Wireless Broadband Router port of the Radius server. The default is 1812. ¾ Shared Secret ： Enter the shared key for authentication server with 8~63 ASCII characters. ¾ Session Timeout ： The authentication interval period between AP and authentication server. 6.2.5 WPA2-Enterprise This security mode is based on Radius authentication server and WPA2 encryption method. WPA2 is used when a RADIUS server is connected to the device.
11N Wireless Broadband Router ¾ Select SSID ： Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. ¾ WPA Algorithms：Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode. ¾ Key Renewal Interval ： Set the key’s renewal period. ¾ Radius Server：Enter the IP address of the Radius server. ¾ Radius Server port ： Enter the authentication port of the Radius server. The default is 1812.
11N Wireless Broadband Router port which allows all the messages to pass. If the port isn’t authenticated successfully, you can keep this port “disable” which just allows 802.1x authentication protocol message to pass. Select “802.1x” from the drop-down menu to enter the following window: ¾ Select SSID ： Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. ¾ WEP：Click “Enable/Disable” to enable or disable the WEP algorithm.
11N Wireless Broadband Router ¾ Session Timeout ： The authentication interval period between AP and authentication server. The default is 3600s. Note: To improve security level, do not use too easy characters. If you are not familiar with these ten security modes, it is recommended to “WPA-Personal” mode. 6.3 Advanced Settings This section is to configure the advanced wireless setting of the Router, including the Radio Preamble, 802.11g/n Rate, Fragmentation Threshold, RTS Threshold, etc.
11N Wireless Broadband Router ¾ BG protection Mode: Auto by default. It is for 11b/g wireless client to connect 11n wireless network smoothly in a complicated wireless area. ¾ Basic Data Rates: For different requirement, you can select one of the suitable Basic Data Rates. Here, default value is (1-2-5.5.-11Mbps…). It is recommended not to modify this value. ¾ Beacon Interval: Set the beacon interval of wireless radio. Default value is 100. It is recommended not to modify this value.
11N Wireless Broadband Router ¾ APSD Capable: It is used for auto power-saved service. The default is disabled. 6.4 WPS Settings WPS (Wi-Fi Protected Setting) can be easy and quick to establish the connection between the wireless network clients and the device through encrypted contents. The users only enter PIN code or press WPS button on the panel to configure it without selecting encryption method and secret keys by manual. In the “Wireless settings” menu, click “WPS settings” to enter the next screen.
11N Wireless Broadband Router ¾ WPS mode：Provide two ways: PBC (Push-Button Configuration) and PIN code. ¾ PBC：Select the PBC or press the WPS button on the front panel of the device for about one second (Press the button for about one second and WPS indicator will be blinking for 2 minutes, which means the WPS is enabled. During the blinking time, you can enable another device to implement the WPS/PBC negotiation between them.
11N Wireless Broadband Router ¾ WPS Auth. Mode ： The authorization mode deployed by WPS, generally WPA/WPA2-personal mode. ¾ WPS Encrypt Type：The encryption type used by WPS, generally AES/TKIP. ¾ WPS key ： The effective key generated by AP automatically. ¾ AP PIN（KEY）：The PIN code used by default. ¾ Reset OOB： When this button is pressed, the WPS client will be idle state, and WPS indicator will be turned off. AP will not respond the WPS client’s requests and the set the security mode as WPA mode.
11N Wireless Broadband Router Lazy: In this mode, the connected device can be Bridge mode or Repeater mode and enter the Router’s BSSID to establish the connection. Bridge: You can wirelessly connect two or more wired networks via this mode. In this mode, you need to add the Wireless MAC address of the connecting device into the Router's AP MAC address table or select one from the scanning table.
11N Wireless Broadband Router 6.6 Wireless Access Control To secure your wireless LAN, the wireless access control is actually based on the MAC address management to allow or block the specific clients to access the wireless network. Select “Wireless Setting->Access Control” to display the following screen: ¾ MAC Address Filter：Enable/disable MAC address filter.
11N Wireless Broadband Router 6.7 Connection Status This page shows wireless client’s connection status, including MAC address, Channel bandwidth, etc. Select “Wireless Setting->connection status” to enter the following screen: ¾ MAC Address：Shows current MAC addresses of the hosts connecting to the Router. ¾ Bandwidth ： Shows current bandwidth of the hosts (wireless client).
11N Wireless Broadband Router Chapter 7: DHCP Server 7.1 DHCP Settings DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When you enable the DHCP Server, the DHCP Server will allocate automatically an unused IP address from the IP address pool to the requesting computer in premise of activating “Obtain an IP Address Automatically”. So specifying the starting and ending address of the IP Address pool is needed.
11N Wireless Broadband Router 7.2 DHCP List and Binding The Static IP assignment is to add a specifically static IP address to the assigned MAC address. You can view the related information in the DHCP server list. ¾ IP Address: Enter the IP address which needs to be bound. ¾ MAC Address: Enter the MAC address of the computer you want to assign the above IP address. Click “Add” to add the entry in the list. ¾ Hostname: The name of the computer which is added a new IP address.
11N Wireless Broadband Router Chapter 8 Virtual Server 8.1 Single Port Forwarding The Router can be configured as a virtual server on behalf of local services behind the LAN port. The given remote requests will be re-directed to the local servers via the virtual server. This section deals with the single port forwarding mainly. The Single Port Forwarding allows you to set up kinds of public services such as web servers, ftp, e-mail and other specialized Internet applications on your network.
11N Wireless Broadband Router example, port 21 for ftp service. ¾ Internal Port: This is the port number of LAN computer set by the Router. The Internet traffic from the external port will forward to the internal port. For example：you can set the internal port NO.66 to act as the external port NO.21 for ftp service. ¾ IP Address: Enter the IP address of the PC where you want to set the applications. ¾ Protocol: Select the protocol (TCP/UDP/Both) for the application.
11N Wireless Broadband Router 8.2 Port Range Forwarding This section deals with the port range forwarding mainly. The Port Range Forwarding allows you to set up a range of public services such as web servers, ftp, e-mail and other specialized Internet applications to an assigned IP address on your LAN. ¾ Start/End Port: Enter the start/end port number which ranges the External ports used to set the server or Internet applications.
11N Wireless Broadband Router ¾ Protocol: Select the protocol (TCP/UDP/Both) for the application. ¾ Delete/Enable: Click to check it for corresponding operation. ¾ Well-Known Service Port: Select the well-known services as DNS, FTP from the drop-down menu to add to the configured one above. ¾ Add: Add the selected well-known port to the policy ID.
11N Wireless Broadband Router 8.3 ALG Service Settings In the context of computer networking, an ALG or application layer gateway consists of a security component that augments a firewall or NAT employed in a computer network. It allows customized NAT traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, BitTorrent, SIP, RTSP, file transfer applications etc.
11N Wireless Broadband Router traffic for not meeting its limited filter criteria. Usually allowing client applications to use dynamic ephemeral TCP/ UDP ports to communicate with the known ports used by the server applications, even though a firewall-configuration may allow only a limited number of known ports.
11N Wireless Broadband Router ¾ DMZ Host IP Address: The IP address of the computer you want to expose. ¾ Enable: Click the checkbox to enable the DMZ host. ¾ IMPORTANT: When the DMZ host is enabled, the firewall settings of the DMZ host will not function. 8.5 UPNP Settings It supports latest Universal Plug and Play. This function goes into effect on Windows XP or Windows ME or this function would go into effect if you have installed software that supports UPnP.
11N Wireless Broadband Router Chapter 9 Traffic Control 9.1 Traffic Control Traffic control is used to limit communication speed in the LAN and WAN. Up to 20 entries can be supported with the capability for at most 254 PCs' speed control, including for IP address range configuration. ¾ Enable Traffic Control: To enable or disable the internal IP bandwidth control. The default is disabled. ¾ Interface: To limit the uploading and downloading bandwidth in WAN port.
11N Wireless Broadband Router as HTTP service. ¾ IP Starting Address: The first IP address for traffic control. ¾ IP Ending Address: The last IP address for traffic control. ¾ Uploading/Downloading: To specify the traffic heading way for the selected IP addresses: uploading or downloading. ¾ Bandwidth: To specify the uploading/downloading Min. /Max. Traffic speed (KB/s), which can not exceed the WAN speed. ¾ Apply: To enable the current editing rule. If not, the rule will be disabled.
11N Wireless Broadband Router 9.2 Traffic Statistics Traffic statistics is used to show the LAN PC’s traffic information. ¾ Enable traffic statistics: check to enable traffic statistics. Usually traffic statistics is disabled, which can improve the Router’s data handling. The default is disabled. If it is enabled, the page will update the PC’s traffic information automatically and be refreshed every 5 seconds. ¾ IP address: The IP address to be shown.
11N Wireless Broadband Router Chapter10 URL Monitor 10.1 URL Monitor This feature is used to record user’s Internet activity, so in terms of this feature, the administrator can check out and control what they can do and have done. ¾ Enable URL Monitor: After checking this feature, the Router will record LAN computer’s URL information, including the visiting Website, your LAN IP address and the time. The Router can record up to 500 entries.
11N Wireless Broadband Router the records will be also lost. The default setting is disabled. ¾ Enable Email: To enable this feature, the URL records will be sent to specified e-mail, which can be solved the problem that the records will be lost when it is over 500 entries. ¾ Receive E-mail Address: Input the received E-mail’s address here. For example: tenda@sina.com.cn ¾ SMTP Server Address: Input the SMTP server address here.
11N Wireless Broadband Router ¾ Entry Triggering Interval: To set sending e-mail’s entry interval. The entry ranges from 100 to 500. For example: if you input 100 here, it means the Router will send a email from “Send Email Address” to “Receive Email Address” in every 100 entries. And then the device will clean all records and start the recording again.
11N Wireless Broadband Router Chapter 11: Security Settings 11.1 Client Filter Settings To benefit your further management to the computers in the LAN, you can control some ports access to Internet by data packet filter function. ¾ Client Filter: Check to enable client filter. ¾ Access Policy: Select one number from the drop-down menu. ¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all settings for the policy.
11N Wireless Broadband Router ¾ Filter Mode: Click one radio button to enable or disable to access the Internet. ¾ Policy Name: Enter a name for the access policy selected. ¾ IP Start/End: Enter the starting/ending IP address. ¾ Port No.: Enter the port range based over the protocol for access policy. ¾ Protocol: Select one protocol (TCP/UDP/Both) from the drop-down menu. ¾ Times: Select the time range of client filter. ¾ Days: Select the day(s) to run the access policy. 11.
11N Wireless Broadband Router ¾ URL Filter: Check to enable URL filter. ¾ Access Policy: Select one number from the ¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all drop-down menu. settings for the policy. ¾ Filter Mode: Click one radio button to enable or disable to access the Internet. ¾ Policy Name: Enter a name for the access policy selected. ¾ Start/End IP: Enter the starting/ending IP address.
11N Wireless Broadband Router 11.3 MAC Address Filter In order to manage the computers in LAN better, you could control the computer’s access to Internet by MAC Address Filter. ¾ MAC Address Filter: Check to enable MAC address filter. ¾ Access Policy: Select one number from the ¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all drop-down menu. settings for the policy.
11N Wireless Broadband Router ¾ MAC Address: Enter the MAC address you want to run the access policy. ¾ Times: Select the time range of client filter. ¾ Days: Select the day(s) to run the access policy. ¾ Apply： Click to make the settings go into effect. For example: if you want to configure the host with MAC address 00:C0:9F: AD:FF:C5 not to access the Internet at 8：00-18：00, you need to set it as above. 11.
11N Wireless Broadband Router 11.5 Remote Web Management This section is to allow the network administrator to manage the Router remotely. If you want to access the Router from outside the local network, please select the “Enable”. ¾ Enable: Check to enable remote web management. ¾ Port: The management port open to outside access. The default value is 80. ¾ WAN IP Address: Specify the range of the WAN IP address for remote management. Note： 1.
11N Wireless Broadband Router 0.0.0.0, it means all hosts in WAN can implement remote Web management. If you change the WAN IP address as 218.88.93.33-218.88.93.35, then only the IP addresses as 218.88.93.33, 218.88.93.34 and 218.88.93.35 can access the Router. For example: If you want to configure the IP address 218.88.93.33 to access the device’s web interface, please set it as follows: 11.
11N Wireless Broadband Router ¾ Enable: Check to enable the local web management. ¾ MAC1/2/3…: Enter the MAC addresses of LAN computers. Note： 1. In the default state, this feature is not enabled. All computers in the LAN can login the Web. 2. For example, if you only allow the MAC address with 00:11:22:33:E4:F5 to access the Web, please set it as above. 11.7 WAN Ping The ping test is to check the status of your internet connection.
11N Wireless Broadband Router Chapter12 Routing Setting 12.1 Routing Table The main duty for a router is to look for a best path for every data frame, and transfer this data frame to a destination. So, it’s essential for the router to choose the best path, i.e. routing arithmetic. In order to finish this function, many transferring paths, i.e. routing table, are saved in the router, for choosing when needed. 12.2 Static Routing This page is used to configure the Router’s static routing.
11N Wireless Broadband Router ¾ Destination LAN IP: The address of the remote host with which you want to construct a static route. ¾ Subnet Mask: The network portion of the Destination LAN IP. ¾ Gateway: The gateway of the next hop, usually the Router or host’s IP address. Note： 1. The gateway must keep the same segment with the Router’s LAN IP address. 2. If the destination IP address is one host’s IP address, the Subnet mask should be 255.255.255.255. 3.
11N Wireless Broadband Router Chapter 13 System Tools 13.1 Time Settings This section is to select the time zone for your location. If you turn off the Router, the settings for time disappear. However, the Router will automatically obtain the GMT time again once it has access to the Internet. ¾ Time Zone: Select your time zone from the drop-down menu. ¾ Customized time: Enter the time you customize. Note： When the Router is powered off, the time setting will be lost.
11N Wireless Broadband Router 13.2 DDNS The DDNS (Dynamic Domain Name System) is supported in this Router. It is to assign a fixed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind the Router. If you want to activate this function, please select “Enable” and a DDNS service provider to sign up.
11N Wireless Broadband Router menu and press “Sign up” for registration. ¾ User Name: Enter the user name the same as the registration name. ¾ Password: Enter the password you set. ¾ Domain Name: Enter the domain name which is optional. For example： In the local host 192.168.0.10 establish a Web server, and register in 3322.org as follows: User name tenda Password 123456 Domain Name tenda.vicp.
11N Wireless Broadband Router 13.3 Backup/Restore Settings The device provides backup/restore settings, so you need set a directory to keep these parameters. ¾ Backup Setting： Click “Backup” button to back up the Router’s settings and select the path for save. Click “Save” to save the configuration files.
11N Wireless Broadband Router ¾ Restore Setting： Click “Browse” button to select the backup files. Click “Restore” button to restore previous settings.
11N Wireless Broadband Router 13.4 Restore to Factory Default Setting This button is to reset all settings to the default values. It means the Router will lose all the settings you have set. So please Note down the related settings if necessary. ¾ Restore: Click this button to restore to default settings. ¾ Factory Default Settings: User Name: admin Password: admin IP Address: 192.168.0.1 Subnet Mask: 255.255.255.
11N Wireless Broadband Router 13.5 Upgrade Firmware The Router provides the firmware upgrade by clicking the “Upgrade” after browsing the firmware upgrade packet which you can download from www.tenda.cn. ¾ Browse: click this button to select the upgrade file. ¾ Upgrade: click this button to start the upgrading process. After the upgrade is completed, the Router will reboot automatically. 13.
11N Wireless Broadband Router 13.7 Password Change This section is to set a new user name and password to better secure your router and network. ¾ User Name: Enter a new user name for the device. ¾ Old Password: Enter the old password. ¾ New Password: Enter a new password. ¾ Re-enter to Confirm: Re-enter to confirm the new password. NOTE: It is highly recommended to change the password to secure your network and the Router.
11N Wireless Broadband Router 13.8 System Log The section is to view the system log. Click the “Refresh” to update the log. Click “Clear” to clear all shown information. If the log is over 150 records, it will clear them automatically. ¾ Refresh: Click this button to update the log. ¾ Clear: Click this button to clear the current shown log. 13.9 Logout After you have finished the settings completely, in logout page click “Yes” to logout the web management page.
11N Wireless Broadband Router Appendix 1：Glossary Access Point(AP): Any entity that has station functionality and provides access to the distribution services, via the wireless medium(WM) for associated stations.
11N Wireless Broadband Router WEP: Wired Equivalent Privacy (WEP) is the method for secure wireless data transmission. WEP adds data encryption to every single packet transmitted in the wireless network. The 40bit and 64bit encryption are the same because of out 64 bits, 40 bits are private. same. Conversely, 104 and 128 bit are the WEP uses a common KEY to encode the data. Therefore, all devices on a wireless network must use the same key and same type of encryption.
11N Wireless Broadband Router difficult for a hacker to learn the key and gain access to the network.WPA2 is the second generation of WPA security and provides a stronger encryption mechanism through Advanced Encryption Standard (AES), which is a requirement for some government users.
11N Wireless Broadband Router Appendix 2: Ask and Question In this part some questions and problems shown during the Router’s usage and installation will be given suggesting answers. If your problems are not in the list, please log into our website www.tenda.cn or send an E-mail to support@tenda.cn, and we will reply you in the first time. 1、Can not login to the Web interface of the Router after you enter the IP address in the address field？ Step 1: check the Router if it works well.
11N Wireless Broadband Router button for 7 seconds to restore to default settings. And then repeat the ping operation. If it still does not work, please contact us. 2、Forget the login password and can not enter the setting page. What can I do? Press the “RESET” button for 7 seconds to restore the Router to default settings. 3、The computer connected with the Router shows IP address conflict. What can I do? Check if there are other DHCP servers in the LAN. If there have, disable them.
11N Wireless Broadband Router the recommended value as 1450 or 1400. 5 、 How to configure and access the Internet via Dynamic IP? In Setup Wizard of the Web utility interface, select “Dynamic IP” connection type and click “Save” to activate it. As some ISPs bind the user computer’s MAC address, you need to clone the Router’s WAN MAC address to the bind21ing PC’s MAC address. Select “MAC Address Clone” in “Advanced Setting” to input your computer’s MAC address and click “Apply” to activate it.
11N Wireless Broadband Router Step 4: input the internal Web service port, for example, 80. Step 5: Input the internal server’s IP address. If your Web server’s IP address is 192.168.0.10, please input it. Step 6: select the communication protocol used by your internal host: TCP, UDP, ICMP. Step 7: click “Apply” to activate the settings.
