Replace detergent pump

ManualsBrandsTennant ManualsMachinesIndustrial Strength Floor Scrubber

IB 340726 (09-2004) 1

No. 340726

Machine: 5680/5700

Published: 09--2004

Rev. 00

INSTRUCTION BULLETIN

NOTE: DO NOT DISCARD the Parts List from the Instruc tion Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individu al parts and will save the cost o f ordering an entire kit.

NOTE:Numbersinparenthesis()arereferencenumbersforpartslistedinBillofMaterials.

Installation instructions for kit number 9000548

SYNOPSIS / PROBLEM:

This kit contains the parts needed to replace the detergent pump on the 5680/57000 model sweepers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 2 hours)

PREPARATION:

1. Drain the solution and recovery tanks.

2. Park the machine on a clean level surface and

turn off the machine.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, and remove key.

3. Lower the scrub head.

INSTALLATION:

1. Open the solution tank cover and lock the cover

into place.

2. Remove the front cover from the machine.

3. Remove the FaST PAK (K) from the machine.

Do not discard the FaST PAK, since it is

reinstalled after the new detergent pump is

installed.

4. If necessary, loosen the detergent box bracket

(L) Refer to Fig. 1.

5. Remove the parts listed in the table below Fig. 1

from the machine. Refer to Fig. 1 for part

locations.

6. Apply a light coat of thread sealant to the

threads on both brass fittings (4).

7. Thread each brass fitting (4) from the previous

step into a brass elbow fitting (3).

NOTE: Refer to Fig 2 for locations and orientation of

parts assembled in the remaining steps of this

bulletin.

8. Thread the fittings assembled in the previous

two steps onto the detergent pump (1).

9. Use two hex screws (7), two washers (9), and

two hex nuts (8) to install the detergent pump (1)

onto the detergent pump plate (2).

10. Cut 21” from the 36” hose (11). Do not discard

the remaining 15” of hose (11).

11. Slide one end of the 21” hose (11) onto the

appropriate fitting on the detergent pump (1).

12. T ighten one hose clamp (10) over the end of the

21” hose (11) attached to the fitting on the

detergent pump (1) in the previous step.

13. Slide one end of the remaining 15” hose (11)

onto the other fitting on the detergent pump (1).

14. T ighten one hose clamp (10) over the end of the

15” hose (11) attached to the fitting on the

detergent pump (1) in the previous step.

15. Slide one hose clamp (10) onto the loose end of

the 15” hose (11).

Summary of content (5 pages)

PAGE 1
INSTRUCTION BULLETIN No. 340726 Machine: 5680/5700 Published: 09--2004 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine manual for future reference. Retaining the Parts List will make it easier to reorder individual parts and will save the cost of ordering an entire kit. NOTE:Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
PAGE 2
16. Use two hex screws (5) and two hex nuts (6) to install the detergent pump plate (2) onto the detergent box bracket (A). 17. Attach the loose end of the 21” hose (11) to the valve coupling (B). If necessary, trim hose to size before attaching it to the valve coupling. 18. Attach the loose end of the 15” hose (11) to the appropriate fitting (D) on the FaST foam filter group. If necessary, trim hose to size before attaching it to the fitting. 19.
PAGE 3
K A L Loosen fasteners here to loosen detergent box bracket. J H I B B F D F J G E C FIG. 1 FaST Air Pump and Detergent Group (000000-- 022740)-- REMOVE ITEMS LISTED BELOW Ref. A B C D E F G H I J Tennant Part No.
PAGE 4
E 6 A 11 (15”) 10 4 3 B 5 1 8 9 3 4 2 7 10 11 (21”) D FIG.
PAGE 5
Bill of Materials for PUMP KIT, DETGT, REPLMT, [5680/5700] o Y Y Y Y Y Y Y Y Y Y Y Tennant Ref. Part No. 9000548 1 1014553 2 1015042 3 1014082 4 150525 5 08716 6 08712 7 09206 8 42368 9 19065 10 613735 11 1006415 Description ) Pump Kit, Detgt, Replmt, [5680/5700] Pump, Detgt, [560S] Plate, Mtg, Detgt Pump Fitting, Brs, E90, CF03/PF02 Fitting, Brs, Str, PM02/BM04 ) Screw, Hex, M6 X 1.0 X 20, SS Nut, Hex, Lock, M6 X 1.0, SS, NL Screw, Hex, M4 X 0.7 X 12, 8.8 Nut, Hex, Std, M4 X 0.