Replace Telemetry Module (NA Only)

ManualsBrandsTennant ManualsMachinesSub-Compact Battery Ride-On Floor Sweeper

IB 9010087 (09- 2015) 1

INSTRUCTION BULLETIN

No. 9010087

Machine: See Below

Published: 09- 2015

Rev. 01

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual p arts and will save th e cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9010085

SYNOPSIS:

This kit contains the parts needed to replace telemetry module on 5680, 5700, 6100E, 6200E, M20,

T20, M30, 8300, S20E, S20, S30, SS5, T5, T5E, T7, SSR, T12, T16, and T17 machines.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 45 minutes)

The IRIS (telemetry module) must be activated to complete this installation. The module will

not

function until it is activated. Call for assistance (North America - Technical Support / Australia -

CCC) activating the module after

all telemetry components have been installed. Have machine

serial number and IRIS module SIM number (located on back of IRIS control box assembly) ready

when calling for activation.

PROTECT THE ENVIRONMENT

Please dispose of packaging mat erials , used machine component s

such as bat t er ies and f luids in an envir onment ally saf e way according

to local was t e disposal regulat ions.

Always remember to recycle.

TROUBLESHOOTING:

1. Prior to replacing the telemetry control box,

call Technical Support / CCC to troubleshoot

the telemetry control box and confirm it needs

to be replaced.

2. Proceed with the instructions in this IB to

replace the telemetry module if

troubleshooting indicates there is a problem

with the telemetry module.

PREPARATIO N:

1. Park the machine on a clean level surface,

turn off the machine, remove the key, and set

the parking brake (if equipped).

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, remove key, and set parking brake (if

equipped).

2. Gas / LP / Diesel Machines: Disconnect the

battery cables from the battery.

Battery Machines: Disconnect the battery

cable from the machine.

W ARNING: Always disconnect battery

cables from machine before working on

electrical components.

Summary of content (3 pages)

PAGE 1
INSTRUCTION BULLETIN No. 9010087 Machine: See Below Published: 09- 2015 Rev. 01 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine manual for future reference. Retaining the Parts List will make it easier to reorder individual parts and will save the cost of ordering an entire kit. NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
PAGE 2
INSTALLATION: 1. Disconnect the telemetry harness and antenna cable from the existing telemetry module. (Fig. 1) 4. Use saved hardware to install the new telemetry module (1) onto the machine. 5. Connect the telemetry harness and antenna cable to the telemetry module (1). (Fig. 1) 6. Reconnect the battery cables to the battery / reconnect the battery cable to the machine. 7. Gas / LP / Diesel Machines: Turn the key to the ON position, but do not start the machine.
PAGE 3
11. Australia Customer Locations: Activate the IRIS (telemetry module): Call CCC (between hours of 8:00 am and 5:00 pm AEST) and ask to be routed to the IRIS expert for assistance to activate the module. The IRIS telemetry system must be activated to complete this install. Have the machine serial number and IRIS module SIM number ready when calling for activation. NOTE: The IRIS (telemetry module) must be activated to complete this installation. The module will not function until it is activated.