Use and Care Manual

NAME OF EACH PART
Battery Case Cover
Liquid Intake
Motor Inside
Joint Nut
(50mm cap)
Intake Hose
OFF Button
ON Button
Discharge Hose
(1300mm)
(600mm)
Rubber Ring
Discharge
Nozzle
Compartment
Discharge Nozzle
Sensor Inlet
Clip
(Stop Line)
Discharge Outlet
Four fuel can adapters
TRFA01-XL OPERATION MANUAL
SEE SAFETY INSTRUCTIONS
ON OTHER SIDE
Caution
*Do not lift up or push down
the pump while it is attached
to the fuel tank.
Insert intake hose through the adapter and
fasten the pump’s joint nut tightly.
Find the adapter that is the best fit and make
sure it is fastened tightly to your supply tank.
H OW TO U SE
A B
C D
B A T T E R Y O P E R A T E D F U E L T R A N S F E R P U M P
H OW TO P LACE THE B ATTERIES
Insert 4 AA batteries according to + and - signs
How to open the battery cover
Place thumb in
grooves as shown
in picture, push and
slide the cover off
in the direction of
the arrow
Direction of Batteries
as indicated in below picture
*Replace all 4
batteries at
the same time
E MERGENCY CASES
WHEN ALL
(4)
BATTERIES ARE
NOT AVAILABLE
*Can pump out approximately 50x 5 gallon fuel cans
using 4 batteries and with 2 batteries can pumps out
approximately 25x 5 gallon fuel cans.
It is recommended to use all 4 AA batteries when you
are able, but it is possible to operate with 2 AA
batteries during emergencies.
W HEN TO
REPLACE THE
BATTERIES
Motor does not operate, even after pressing ON switch or transfer
rate becomes slower than in normal operation.
Batteries can begin to discharge if they are stored for a long period
of time. Check the expiration dates of batteries.
*Use the same brand/type of batteries
NO
FFO
Attach the discharge hose to
your receiving tank using the clip,
make sure the discharge nozzle
is in a vertical position.
*Make sure that the supplying tank and receiving tank
are on the same level when pump is operating.
*For tanks which are not fixed with the clip, make sure the
discharge nozzle is vertical to the liquid level.
Start the flow of fuel by pressing
the ON button.
Caution
After automatically stopping, bring
the discharge hose up above the
tank to drain the excess fuel or
liquid back into the supply tank.
*Automatically stops when the
fuel reaches the stop line.
Put the discharge nozzle in discharge
nozzle compartment and lock into
place with clip.
*Place the discharge nozzle into
discharge nozzle compartment
properly after fueling. In the event the
fuel tank falls over, and the discharge
hose is not in its storage hole, liquid
can leak out.
Caution
Caution
Receiving tank
HOW TO STORE
When the pump is not being used for long periods of time, take the
pump out of the tank, make sure no remaining fuel is in the hose,
and wipe it down with a cloth before storing it.
Make sure to take the batteries out before storing the pump.
Do not store pump in enclosed airtight container.
PRODUCT SPECIFICATIONS
Model TRFA01-XL
Battery:
AAx4, 3A
(not included)
Flux:
Major
materials:
Polypropylene,
Polyethylene,
Polyacetal
Operating
temperature:
Approx.
Compatible
liquids:
Pollution
degree:
Gasoline, Diesel,
Kerosene, Light Oil
t e r a p u m p . n e t
1941 E OCCIDENTAL ST
SANTA ANA, CA 92705
[e-mail]
1-877-251-2288
Thank you for your purchase of the TRFA01-XL. Please
read this manual carefully to ensure proper use. Do not
leave this pump unattended while in operation.
Motor:
3VDC
Altitude:
2000 m
2
Installation
category:
I
5°C to 45°C
About 8.9 LPM
(2.3 GPM)