Quick start Guide

ManualsBrandsTeradek ManualsCamcorder & Camera PeripheralsSlice 676 Rackmount H.264 Decoder

Stream/Menu Control dial:

▲: Go live, start/stop push, start/stop recordings, select characters

, ,▼: Selects options from streaming/recording prompts

: Back, move to higher menu level

● (Control dial button press): Confirm selection, enter main menu, open selected menu

▲

NETWORK CONNECTION

Connect A/C power to the Power Input (E). Attach the included Wireless antennas via the threaded

RP-SMA connectors (L).

Connect the SDI output from your video source to the HD-SDI (F), or the HDMI (G) input on the Slice

encoder.

Connect Slice to your network via the 10/100/1000 Ethernet port (H).

A: Power button

B: USB ports

C: Reset button

D: Stream/menu control dial

E: A/C input

F: SD/HD/3G−SDI input/output

G: HDMI input/output

H: 10/100/1000 Ethernet

I: Reset button

J: Headphone audio output

K: Mic/Line stereo input

L: RP-SMA connectors

E I

AC adapter

WiFi antennas

Connect to Slice’s Wi−Fi network (AP mode): Teranet−XXXXX (serial number of the device). If Slice has

already been configured to connect to another network (Infrastructure mode), connect to that instead.

Plug an Ethernet cable into Slice’s 10/100/1000 Ethernet port and connect it to an Ethernet switch

or router. Use the Menu joystick to navigate to the Network Setup menu, and verify that Ethernet is

enabled and set to DHCP.

Open a web browser and navigate to http://172.16.1.1, or find Slice using Bonjour.

Connect your computer to the same network as Slice. From the main status screen, press ▼ on Slice’s menu

joystick to display Slice’s IP address on the front panel.

Slice’s Wi−Fi can also be configured to join your network via the web UI or front panel.

Open a web browser and navigate to Slice’s IP address, or find Slice using Bonjour.

Slice has a built in web user interface (web UI) for configuring stream destinations, encoder

parameters, and other settings. The interface can be accessed by connecting via Wi−Fi or Ethernet.

CONNECT VIA WI−FI

CONNECT VIA ETHERNET

Slice 700 series encoders support 1080p, 60fps encoding using both HEVC and H.264 codecs. HEVC

provides the most efficient encoding for both low bitrate and high quality applications, while H.264

supports a wider variety of streaming platforms and is one of the most common video codecs worldwide.

The codec can be switched between HEVC and H.264 from the Encoder Settings and Video Stream Output

settings pages on the web UI, or from the Video Setup menu on the front panel.

NEED MORE HELP?

1. Support: http://support.teradek.com → Contains tips, information and all the latest firmware & software updates.

TERADEK SUPPORT STAFF: support@teradek.com or call 888−941−2111 ext2 (Mon−Fri 9am to 6pm PST)

POWER AND CONNECT

HEVC AND H.264

Summary of content (2 pages)

PAGE 1
NETWORK CONNECTION 2 Slice has a built in web user interface (web UI) for configuring stream destinations, encoder parameters, and other settings. The interface can be accessed by connecting via Wi−Fi or Ethernet.
PAGE 2
4 STREAM TO THE INTERNET 1 Open Slice’s web UI, then select the Video Stream Output menu if it is not already displayed. 2 Select Internet Streaming as the Stream Mode and choose a platform − Facebook, Ustream, Livestream, YouTube, Twitch − or select manual RTMP. 3 Enter your credentials and choose a channel/event, or enter the RTMP destination info and click Apply. 4 5 DECODER SETUP 7 Ensure that Slice’s encoder and decoder are on the same network.