User Manual

119
12
10
After switching on the thermostat will start to display the
sensor temperature. If it is below the current set
temperature, voltage is applied to the load. The indicator
starts to glow red.
Use or to change the heating temperature. The
screen will first display the operating mode, then the set
temperature of this mode.
«+» «–»
For viewing of necessary section of the menu press
certain number of times button . For the selection
and change use buttons 5 seconds after
the last push of the buttons, there is a return to the
temperature display
« »≡
and . «+» «–»
.
To unlock, consistently tap 3 buttons from
left to right. Simultaneously with taps, the
screen will display 3 dashes.
BUTTONS AUTOLOCK (PROTECTION AGAINST
FALSE BUTTON TAPPING) It turns on 20 s. after the
last button tap, when the «Button blocking» function
is off.
.
Button blocking (child and public
protection)
In order to enable (disable) button blocking
press the and buttons at the same
time for 6 sec till up to appearance in
indicator
«+» «–»
« » (« »).Loc unLocor running line
For reset of all settings to factory (besides
Wi-Fi settings) press button during 30
second. before emergence on the screen of
the inscription After release of the
button thermostat will reload.
«–»
«dEF».
Reduce to factory reset
Holding button «–» during 12 seconds will
display on the screen the version of insertion.
After release of button, thermostat will return
to the normal mode.
If the firmware version of thermostat does not meet the
version mentioned in the manual, download from
website Operation Manual for the required version. The
website address can be found in the instructions in the
Contacts section.
Our company reserves the right to make changes to its
firmware, cloud interface and applications for iOS and
Android for improving the energy efficiency of the device
and for optimizing its operation.
Viewing of firmware version (current
firmware version F2.5)
Robot mode
(factory setting « »
— Hand mode).
hnd
The controller has
4 operating modes.
One of two modes
can be set from the
thermostat buttons only:
hnd« » —
« » — .
Hand mode
or Schedule modeSch
The brightness
in the mode of waiting
(factory setting
a range of change
6,
0...9)
Floor
temperature correction
(factory setting 0,
a range of change ±9,9 °С,
step 0,1 °С)
Installed load
capacity
( , factory setting 2.0
a range of change 0, 1...25,0 к , 0 W
the step length depends
on power capacities)
Remote management
blocking by
thermostat
(factory setting
«LАn» — blocking of changes
through local area network )
PIN-code or local IP
(the section is available
when connected thermostat
to a Wi-Fi network)
Operating mode Wi-Fi
( factory setting « »
— Client mode
Cli
)
1
time
2
times
when
connection
to a Wi-Fi
network 5 times
otherwise
4 times
when
connection
to a Wi-Fi
6network times
otherwise
times5
when
connection
to a Wi-Fi
7network times
otherwise
times6
when
connection
to a Wi-Fi
network
3 times
when
connection
to a Wi-Fi
network 4 times
otherwise
3 times
Hand mode. Adjustable via the app or controller
buttons. It allows you to maintain one pre-set
temperature.
Access point mode.
Switched of.
Schedule mode. . Adjustable via the app If the
Preheat feature is enabled on the app, the screen
will display .«Prh»
Client mode.
Switched on blocking of changes from «cloud».
Temporary If to change the temperature of
the setting in the mode Schedule to the timetable,
the thermostat will support it until the end of the
current period. The outcome from the temporary
mode under: the return of the setting back, the
shutdown of the supply, turning on of the period of
the leaving.
mode.
Wi-Fi is turned off.
Switched on blocking of changes through local area
network.
Total blocking of management from the cloud. It is
possible to change parameters only using buttons of
the thermostat.
Away Is tuned only by means of the app For
the cancellation of the mode Away withhold middle
button during 4 seconds to the apparition of «oFF»
in the indicator. After release of the button the
thermostat will return in the acting mode before
beginning of the period of the Away.
mode. .
With 0 in the screen only points will be displayed:
left — indicator of the presence of the tension of the
power supply; middle — is reflected state of loading;
right — is reflected state of Wi-Fi net.
Adjustable via the app or controller buttons. If
necessary, it is possible to make correction to the
floor temperature at Indicator of the thermostat.
Adjustable via the app or controller buttons. For
proper operation of energy consumption statistics, it
is required to insert installed load capacity.
When Wi-Fi is turned off, the item is unavailable.
When connected to the cloud, it outputs a PIN-code
for registration. When you connect to Wi-Fi, but the
lack of communication with the cloud will output
your local IP address.
Enabling sleep mode
Hold the button for 4 seconds (3 dashes
will appear on the display one by one) before
appearing on the display For a
complete shutdown, the circuit breaker should
be turned off.
« »≡
«oFF».
To disable sleep mode, also hold down the
middle button for 4 seconds until pops
up on the screen.
« »on
Possible reason: no power supply voltage.
Possible reason:
switched on blocking of changes from
«cloud»
.
«OC» — open of circuit of the sensor
Required: go to the thermostat menu section and
change its status to T
«blc»
( , ««oFF» see able 1 Remote
management blocking by thermostat »).
What should be done: check the junction of the
temperature sensor with the thermostat and its circuit,
check for mechanical damages along the entire length of
the connecting wire and no power wiring that passes
close.
Required: check availability of power supply voltage using
a voltmeter. If power supply voltage is available then
contact the Service center please.
Possible cause: Failed connection, damage to the sensor
circuit, or temperature out of range (see Specifications).
The load does not operate according to the settings,
every 5 seconds the screen displays or «OC» «SC»
The temperature controller has switched to the
Emergency Timer Mode.
Neither indicator nor display light up upon thermostat
switch-on
«SC» — short circuit of the sensor
Operation in the Emergency Timer Mode: the mode will
ensure the operation of the underfloor heating in case of
damage to the sensor: t he user selects the time of the
work of the applied force, the rest time in the 30 –
minutes cyclic interval the applied force will be switched
off. The time of the work of the applied force can be
installed in the range oFF, 1...29 minutes, on. For the
purpose that applied force will work constantly elect
«on»
«oFF»
, for the purpose to switch off it completely select
.
The thermostat does not respond to changing
settings on the app
CONTROL FROM THE BUTTONS
Menu section
Table 1. FUNCTION MENU
Press
« »button ≡
NotesScreen
POSSIBLE PROBLEMS, CAUSES
AND WAYS TO OVERCOME THEM