Cut Sheet

NORTH AMERIC A
TEL
: 1 866 228 3762
FAX: [phone]
Test & Measurement Regional Sales
LATIN AMERICA
TEL
: [phone]
FAX: [phone]
ASIA PACIFIC
TEL
: [phone]
FAX: [phone]
EMEA
TEL
: [phone]
FAX: [phone]
www.jdsu.com/know
L
il’ Buttie PRO
™
T
elephone Test Set
Ordering Information
Lil’ Buttie PRO Telephone Test Set LB220
– Includes 1.22 m (4 ft) RJ11 to angled bed-of-nails cord set (LB35),headset with boom microphone (LB40B),
and 9-volt battery.
Lil’ Buttie PRO Telephone Test Set with protective boot LB220-BT
– Includes protective boot (LB81), 1.22 m (4 ft) RJ11 to angled bed-of-nails cord set (LB35),
headset with boom microphone (LB40B), and 9-volt battery.
Lil’ Buttie PRO Telephone Test Set with hook-type belt clip LB230
– Includes hook-type belt clip (LB70B), 1.22 m (4 ft) RJ11 to angled bed-of-nails cord set (LB35),
headset with boom microphone (LB40B), and 9-volt battery.
Lil’ Buttie PRO Telephone Test Set for use outside North America LB220UK/AUS
– 100 ms hook flash,37/63 make/break ratio
– Includes 1.22 m (4 ft) RJ11 to angled bed-of-nails cord set (LB35),and 9-volt battery.
Accessories
RJ11 to piercing pin clips,1.22 m (4 ft) with strain relief LB20B
RJ11 to angled bed-of-nails cord set, 1.22 m (4 ft) with strain relief LB35
RJ11 to alligator clips,1.22 m (4 ft) with strain relief LB10B
Headset with boom microphone,mini over-the-ear LB40B
Headset with cushioned earpiece,full over-the-head LB45B
Modular adapter,4-position LB64
Modular adapter,6-position LB66
Modular adapter,8-position LB68
Belt clip, rugged hook type on battery door LB70B
Protective rubber boot LB81
Nylon pouch LB80
Specifications
Electrical
Battery current consumption (typical)
Bell (timed out) 15 µA
Talk
– CWCID off 2 mA
– CWCID on 12 mA
– MON 25 mA
Battery life (alkaline,450 mA-hr, included)
Operating 18 hrs (min); 225 hrs (max)
Standby 3.4 yrs
Typical 30–50 hrs
Return loss 14 dB at 600 Ω
Line current range 15 to 120 mA
Apparent line resistance 275 Ω at 20 mA
Monitor mode impedance >130 kΩ
General
Pulse Dialing
Pulse rate 10 pps ±10%
Make/break ratio 60/40% ±2%
Interdigit interval 820 ms
Resistance in break 120 kΩ
DTMF Output (into 600 Ω)
Tone frequency error ±1.5%
Tone Level
– High group –6 dBm ±2 dB
– Low group –8 dBm ±2 dB
High vs low difference 2 dBm ±1 dB
Memory Dialing
Type 5 programmed and last number redial
Memory capacity 19 digits
Memory retention w/battery >2 yrs
Flash duration 600 ms ±50 ms
Pause duration
– Tone 3.0 s
– Pulse 3.4 s
Ringer equivalent (Bell mode) 0.0 (no ringer load)
Measurement
Voltage 0 to 128 V DC ±5%
Current 10 to 140 mA ±5%
Environmental
Temperature
– Operating 0 to 50°C;
– Storage –20 to 60°C
Physical
Length (w/o lanyard) 18.4 cm (7.25 in)
Width 6.4 cm (2.50 in)
Height 4.3 cm (1.68 in)
Weight (with cord set) <284 gm (10 oz)
Warranty
JDSU guarantees that its products will be free of all defects in material and workmanship.This warranty extends for the period of
12 months for test instruments and 3 months for cables from date of manufacture or purchase (proof of purchase required).
All products deemed defective under this warranty will be repaired or replaced at the discretion of JDSU.No further warranties,
either implied or expressed,will apply,nor will JDSU assume responsibility for operation of this device.
Product specifications and descriptions in this document subject to change without notice. © 2008 JDS Uniphase Corporation June 2008 30149350 000 0608 LBPRO.DS.NET.TM.AE