Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsDev KitsPCB design board

www.ti.com

Bill of Materials, Board Layout, and Schematics

4 Bill of Materials, Board Layout, and Schematics

4.1 Bill of Materials

Table 4. Bill of Materials

Count

RefDes Value Description Size Part Number

-001 -002

1 1 C1 10uF Capacitor, Ceramic, 25V,X7R, 10% 1206 STD

2 2 C2, C4 0.1uF Capacitor, Ceramic, 25V, X7R, 10% 0603 STD

1 1 C3 10uF Capacitor, Ceramic, 6.3V, X7R, 10% 0805 STD

0 0 C5, C6 Open Capacitor, Ceramic, 25V, X7R, 10% 0603 STD

2 2 D1, D2 LTST-C190CKT Diode, LED, Red, 1.8-V, 20-mA, 20-mcd 0603 LTST-C190CKT

1 1 D3 BZX84C5V1-7 Diode, Zener, 5.1V, 350-mW SOT-23 BZX84C5V1-7

1 1 J1 PEC02SAAN Header, Male 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN

1 1 J2 ED555/3DS Terminal Block, 3-pin, 6-A, 3.5mm 0.41 x 0.25 inch ED555/3DS

1 1 J3 PEC05SAAN Header, Male 5-pin, 100mil spacing, 0.100 inch x 5 PEC05SAAN

1 1 J4 PEC03SAAN Header, Male 3-pin, 100mil spacing, 0.100 inch x 3 PEC03SAAN

4 4 JP1, JP2, JP3, PEC02SAAN Header, 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN

JP4

3 3 JP5, JP6, JP7 PEC03SAAN Header, 3 pin, 100mil spacing, 0.100 inch x 3 PEC03SAAN

1 1 R1 21.5k Resistor, Chip, 1/16W, 1% 0603 STD

2 2 R2, R4 1.50K Resistor, Chip, 1/16W, 1% 0603 STD

1 1 R3 750 Resistor, Chip, 1/16W, 1% 0603 STD

1 1 R5 6.65k Resistor, Chip, 1/16W, 1% 0603 Std

1 1 R6 100k Potentiometer, 1/4 Cermet, 12-Turn, Top-Adjust 0.25x0.17 inch 3266W-1-104LF

1 1 R7 4.75k Resistor, Chip, 1/16-W, 1% 0603 STD

0 0 TP1, TP2, TP3 Open Test Point, 0.020 Hole STD

1 0 U1 BQ24210DQC IC, 800mA, Single-Input, Single Cell Li-Ion Battery Solar TDFN-10 BQ24210DQC

Charger with bi-directional Power Path

0 1 U1 BQ24212DQC IC, 800mA, Single-Input, Single Cell Li-Ion Battery Solar TDFN-10 BQ24212DQC

Charger with bi-directional Power Path

7 7 — Shunt, 100-mil, Black 0.1 929950-00

1 1 — PCB, 2.64" x 2.1" x 0.062" HPA678

1 1 — Label 1.25 x 0.25 inch THT-13-457-10

Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.

2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.

3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.

4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFG's

components.

5. Install label after final wash. Text shall be 8 pt font. Text shall be per Table 1.

Table 1

Assembly Text

Number

HPA678-001 BQ24210EVM-678

HPA678-002 BQ24212EVM-678

SLUU477A– December 2010– Revised August 2011 800-mA, Single-Input, Single-Cell, Li-Ion Battery Solar Charger With Power Path

Submit Documentation Feedback