Data Sheet
Table Of Contents
- 1 Module Overview
- Table of Contents
- 2 Revision History
- 3 Device Comparison
- 4 Terminal Configuration and Functions
- 5 Specifications
- 5.1 Absolute Maximum Ratings
- 5.2 ESD Ratings
- 5.3 Recommended Operating Conditions
- 5.4 Current Consumption Summary: 2.4 GHz RF Band
- 5.5 Current Consumption Summary: 5 GHz RF Band
- 5.6 TX Power Control for 2.4 GHz Band
- 5.7 TX Power Control for 5 GHz Band
- 5.8 Brownout and Blackout Conditions
- 5.9 Electrical Characteristics for DIO Pins
- 5.10 WLAN Receiver Characteristics
- 5.11 WLAN Transmitter Characteristics
- 5.12 BLE and WLAN Coexistence Requirements
- 5.13 Reset Requirement
- 5.14 Thermal Resistance Characteristics for MOB Package
- 5.15 Timing and Switching Characteristics
- 5.16 External Interfaces
- 6 Detailed Description
- 7 Applications, Implementation, and Layout
- 8 Environmental Requirements and SMT Specifications
- 9 Device and Documentation Support
- 10 Mechanical, Packaging, and Orderable Information
- Important Notice
TI Confidential – NDA Restrictions
ADVANCEINFORMATION
15
CC3135MOD
www.ti.com
SWRS225A –FEBRUARY 2019–REVISED AUGUST 2019
Submit Documentation Feedback
Product Folder Links: CC3135MOD
Terminal Configuration and FunctionsCopyright © 2019, Texas Instruments Incorporated
Table 4-2. Signal Descriptions (continued)
FUNCTION SIGNAL NAME
PIN
NO.
PIN
TYPE
SIGNAL
DIRECTION
DESCRIPTION
FLASH SPI
FLASH_SPI_DIN 13 I I External serial Flash interface: SPI data in
FLASH_SPI_CS 14 O O
External serial Flash interface: SPI chip select (active
low)
FLASH_SPI_CLK 15 O O External serial Flash interface: SPI clock
FLASH_SPI_MOSI 17 O O External serial Flash interface: SPI dta out
UART
UART1_nRTS 44 I/O O UART1 request-to-send (active low)
UART1_TX 46 I/O I UART TX data
UART1_RX 47 I/O O UART RX data
UART1_nCTS 51 I/O I UART1 clear-to-send (active low)
Sense-On-
Power
SOP2 23
(3)
O I Sense-on-power 2
SOP1 24 I I Configuration sense-on-power 1
SOP0 34 I I Configuration sense-on-power 0
Power
VBAT1 37 - - Power supply for the module
VBAT2 40 - - Power supply for the module
nHIB nHIB 4 I I
Hibernate signal input to the NWP subsystem (active
low)
RF RF_ABG 31 I/O I/O WLAN analog RF 802.11 a/b/g/n bands
Test Port
TEST_58 48 O O Test Signal
TEST_59 49 I I Test Signal
TEST_60 50 O O Test Signal
TEST_62 52 O O Test Signal
(1) LPDS retention unavailable.
(2) The CC3135MOD modules are compatible with TI BLE modules using an external RF switch.
(3) This pin has dual functions: as a SOP[2] (device operation mode), and as an external TCXO enable. As a TXCO enable, the pin is an
output on power up and driven logic high. During hibernate low-power mode, the pin is in a Hi-Z state but is pulled down for SOP mode
to disable TCXO. Because of the SOP functionality, the pin must be used as an output only.