Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLogic ICsLogic IC - Multiplexer Multiplexer Single supply SOIC 16 N

Data sheet acquired from Harris Semiconductor

SCHS247A

Features

• Buffered Inputs

• Typical Propagation Delay

- 6.3ns at V

= 5V, T

= 25

C, C

= 50pF

• Exceeds 2kV ESD Protection MIL-STD-883, Method

3015

• SCR-Latchup-Resistant CMOS Process and Circuit

Design

• Speed of Bipolar FAST™/AS/S with Signiﬁcantly

Reduced Power Consumption

• Balanced Propagation Delays

• AC Types Feature 1.5V to 5.5V Operation and

Balanced Noise Immunity at 30% of the Supply

• ±24mA Output Drive Current

- Fanout to 15 FAST™ ICs

- Drives 50Ω Transmission Lines

Description

The CD74AC253 and ’ACT253 dual 4-input multiplexers that

utilize Advanced CMOS Logic technology. One of the four

sources for each section is selected by the common Select

inputs, S0 and S1. When the Output Enable (

1OE or 2OE) is

HIGH, the output is in the high-impedance state.

Pinout

CD54ACT253

(CERDIP)

CD74AC253, CD74ACT253

(PDIP, SOIC)

TOP VIEW

Ordering Information

PART

NUMBER

TEMP.

RANGE (

C) PACKAGE

CD74AC253E 0 to 70

C, -40 to 85,

-55 to 125

16 Ld PDIP

CD74AC253M 0 to 70

C, -40 to 85,

-55 to 125

16 Ld SOIC

CD54ACT253F3A -55 to 125 16 Ld CERDIP

CD74ACT253E 0 to 70

C, -40 to 85,

-55 to 125

16 Ld PDIP

CD74ACT253M 0 to 70

C, -40 to 85,

-55 to 125

16 Ld SOIC

NOTES:

1. When ordering, use the entire part number. Add the suffix 96 to

obtain the variant in the tape and reel.

2. Wafer and die for this part number is available which meets all elec-

trical specifications. Please contact your local TI sales office or cus-

tomer service for ordering information.

1OE

GND

2OE

August 1998 - Revised May 2000

CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.

FAST™ is a Trademark of Fairchild Semiconductor.

CD74AC253,

CD54/74ACT253

Dual 4-Input Multiplexer, Three-State

Summary of content (15 pages)

PAGE 1
CD74AC253, CD54/74ACT253 Data sheet acquired from Harris Semiconductor SCHS247A Dual 4-Input Multiplexer, Three-State August 1998 - Revised May 2000 Features Description • Buffered Inputs The CD74AC253 and ’ACT253 dual 4-input multiplexers that utilize Advanced CMOS Logic technology. One of the four sources for each section is selected by the common Select inputs, S0 and S1. When the Output Enable (1OE or 2OE) is HIGH, the output is in the high-impedance state. • Typical Propagation Delay - 6.
PAGE 2
CD74AC253, CD54/74ACT253 Functional Diagram 1 1OE 6 1I0 5 1I1 7 1Y SEL/MUX 4 1I2 3 1I3 S0 S1 2I0 2I1 2I2 2I3 2OE 14 2 10 11 9 2Y SEL/MUX 12 13 GND = 8 VCC = 16 15 TRUTH TABLE SELECT INPUTS DATA INPUTS ENABLE INPUTS OUTPUT S1 S0 nI0 nI1 nI2 nI3 nOE nY X X X X X X H Z L L L X X X L L L L H X X X L H L H X L X X L L L H X H X X L H H L X X L X L L H L X X H X L H H H X X X L L L H H X X X H L H Select inputs S1 and S0
PAGE 3
CD74AC253, CD54/74ACT253 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 6V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±50mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .
PAGE 4
CD74AC253, CD54/74ACT253 DC Electrical Specifications (Continued) TEST CONDITIONS PARAMETER Low Level Output Voltage -40oC TO 85oC 25oC -55oC TO 125oC SYMBOL VI (V) IO (mA) VCC (V) MIN MAX MIN MAX MIN MAX UNITS VOL VIH or VIL 0.05 1.5 - 0.1 - 0.1 - 0.1 V 0.05 3 - 0.1 - 0.1 - 0.1 V 0.05 4.5 - 0.1 - 0.1 - 0.1 V 12 3 - 0.36 - 0.44 - 0.5 V 24 4.5 - 0.36 - 0.44 - 0.5 V 75 (Note 6, 7) 5.5 - - - 1.65 - - V 50 (Note 6, 7) 5.
PAGE 5
CD74AC253, CD54/74ACT253 ACT Input Load Table INPUT UNIT LOAD S0, S1, nI0, nI1 1 nOE 0.83 NOTE: Unit load is ∆ICC limit specified in DC Electrical Specifications Table, e.g., 2.4mA max at 25oC. Switching Specifications Input tr, tf = 3ns, CL = 50pF (Worst Case) -40oC TO 85oC PARAMETER -55oC TO 125oC SYMBOL VCC (V) MIN TYP MAX MIN TYP MAX UNITS tPLH, tPHL 1.5 - - 227 - - 250 ns 3.3 (Note 9) 7.2 - 25 7 - 28 ns 5 (Note 10) 5.2 - 18.2 5 - 20 ns 1.
PAGE 6
CD74AC253, CD54/74ACT253 tr = 3ns tf = 3ns INPUT LEVEL 90% OUTPUT DISABLE VS 10% GND tPZL tPLZ VS 0.2VCC OUTPUT: LOW TO OFF TO LOW tPHZ tPZH VOH (≠ VCC) 0.8 VCC VS OUTPUT: HIGH TO OFF TO HIGH OUTPUTS ENABLED OTHER INPUTS (TIED HIGH OR LOW) OUTPUTS DISABLED OUTPUT DISABLE OUTPUTS ENABLED GND (tPHZ, tPZH) OPEN (tPHL, tPLH) 2 VCC (tPLZ, tPZL) (OPEN DRAIN) 500Ω† RL DUT WITH THREESTATE OUTPUT VOL (≠ GND) OUT 500Ω† RL CL 50pF †FOR AC SERIES ONLY: WHEN VCC = 1.5V, RL = 1kΩ FIGURE 1.
PAGE 7
PACKAGE OPTION ADDENDUM www.ti.
PAGE 8
PACKAGE OPTION ADDENDUM www.ti.com 15-Oct-2009 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties.
PAGE 9
PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant CD74AC253M96 SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 CD74ACT253M96 SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.
PAGE 10
PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD74AC253M96 SOIC D 16 2500 333.2 345.9 28.6 CD74ACT253M96 SOIC D 16 2500 333.2 345.9 28.
PAGE 11
PAGE 12
PAGE 13
PAGE 14
PAGE 15
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.