Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLogic ICsLogic IC - Flip-Flop Standard Three-state, Inverted DIP 20

M54/74HCT564

M54/74HCT574

September 1993

HCT564 INVERTING - HCT574 NON INVERTING

OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT

B1R

(Plastic Package)

ORDER CODES :

M54HCTXXXF1R M74HCTXXXM1R

M74HCTXXXB1R M74HCTXXXC1R

F1R

(Ceramic Package)

M1R

(Micro Package)

C1R

(Chip Carrier)

PIN CONNECTION (top view)

.HIGH SPEED

MAX

= 62 MHz (TYP.) AT V

=5V

.LOW POWER DISSIPATION

=4µA (MAX.) AT T

=25°C

.COMPATIBLE WITH TTL OUTPUTS

= 2V (MIN.) V

= 0.8V (MAX)

.OUTPUT DRIVE CAPABILITY

15 LSTTL LOADS

.SYMMETRICAL OUTPUT IMPEDANCE

= I

= 6 mA (MIN.)

.BALANCEDPROPAGATION DELAYS

PLH

PHL

.PIN AND FUNCTION COMPATIBLE

WITH 54/74LS564/574

DESCRIPTION

The M54/74HCT564 and M54HCT574 are high

speed CMOS OCTAL D-TYPE FLIPFLOP WITH 3-

STATE OUTPUTSfabricated in silicon gate C

MOS

technology. They have the same high speed per-

formance of LSTTL combined with true CMOS low

power comsuption. These 8-bit D-type flip-flops are

controlled by a clockinput(CK) and anouput enable

input (OE).On thepositive transition of theclock,the

Q outputs will be set to thelogic statethatwere setup

at the D inputs (HCT574) or their complements

(HCT564).

While the OE input is low, the eight outputs will be

in a normal logic state (high or low logic level), and

while high level, the outputs will be in a high imped-

ance state. The output control does not affect the in-

ternal operation of flip-flops. That is, theold data can

be retained or the new data can be entered even

while the outputs are off. The application engineer

has a choice of combination of inverting and non-in-

verting outputs. The 3-state output configuration

and the wide choice of outline make bus-organized

systemssimple. All inputs are equipped withprotec-

tion circuits against static discharge and transient

excess voltage. This integrated circuit has input and

output characteristics that are fully compatible with

54/74 LSTTL logic families. M54/74HCT devices

are designed to directly interface HSC

MOS sys-

tems with TTL and NMOS components. They are

also plug in replacements for LSTTL devices giving

a reduction of power consumption.

HCT564 HCT574 HCT564 HCT574

1/13

Summary of content (13 pages)

PAGE 1
M54/74HCT564 M54/74HCT574 OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT HCT564 INVERTING - HCT574 NON INVERTING . . . . . . . HIGH SPEED fMAX = 62 MHz (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 4 µA (MAX.) AT TA = 25 °C COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN.) VIL = 0.8V (MAX) OUTPUT DRIVE CAPABILITY 15 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOL = IOH= 6 mA (MIN.
PAGE 2
M54/M74HCT564/574 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION (HCT564) PIN No SYMBOL 1 OE 2, 3, 4, 5, 6, 7, 8, 9 D0 to D7 12, 13, 14, 15, 16, 17, 18, 19 Q0 to Q7 11 CLOCK 10 20 GND V CC NAME AND FUNCTION PIN DESCRIPTION (HCT574) PIN No SYMBOL 1 OE Data Inputs 2, 3, 4, 5, 6, 7, 8, 9 D0 to D7 Data Inputs 3 State outputs 12, 13, 14, 15, 16, 17, 18, 19 Q0 to Q7 3 State outputs Clock Input (LOW to HIGH, edge triggered) 11 CLOCK Ground (0V) Positive Supply Voltage 10 20 GND
PAGE 3
M54/M74HCT564/574 TRUTH TABLE INPUTS OE H L L L CK X OUTPUTS D X Q (HCT574) Z Q (HCT564) Z X L H NO CHANGE L H NO CHANGE H L LOGIC DIAGRAMS HCT574 HCT564 3/13
PAGE 4
M54/M74HCT564/574 ABSOLUTE MAXIMUM RATINGS Symbol Value Unit VCC VI Supply Voltage DC Input Voltage -0.5 to +7 -0.5 to VCC + 0.5 V V VO DC Output Voltage -0.5 to VCC + 0.
PAGE 5
M54/M74HCT564/574 DC SPECIFICATIONS Test Conditions Symbol Parameter VCC (V) VIH High Level Input Voltage 4.5 to 5.5 V IL Low Level Input Voltage 4.5 to 5.5 V OH High Level Output Voltage VOL II ICC ∆ICC Low Level Output Voltage Input Leakage Current Quiescent Supply Current Additional worst case supply current Value TA = 25 oC 54HC and 74HC Min. Typ. Max. 2.0 -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 2.0 0.8 4.5 VI = IO=-20 µA VIH or IO=-6.0 mA V IL 4.
PAGE 6
M54/M74HCT564/574 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = t f = 6 ns) Test Conditions TA = 25 oC 54HC and 74HC Symbol Parameter VCC (V) CL (pF) tTLH tTHL tPLH tPHL Output Transition Time Propagation Delay Time 4.5 50 Typ. 7 Max.
PAGE 7
M54/M74HCT564/574 SWITCHING CHARACTERISTICS TEST WAVEFORM CLOCK DUTY : 50% 1 fMAX = TCK EACH FLIP-FLOP SHALL BE SET HIGH WHEN SWITCH IS CONNECTED TO GND LINE AND IT SHALL BE SET LOW WHEN SWITCH IS CONNECTED TO VCC LINE.
PAGE 8
M54/M74HCT564/574 TEST CIRCUIT ICC (Opr.) INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST.
PAGE 9
M54/M74HCT564/574 Plastic DIP20 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.254 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.010 1.65 0.055 0.065 b 0.45 0.018 b1 0.25 0.010 D 25.4 1.000 E 8.5 0.335 e 2.54 0.100 e3 22.86 0.900 F 7.1 0.280 I 3.93 0.155 L Z 3.3 0.130 1.34 0.
PAGE 10
M54/M74HCT564/574 Ceramic DIP20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 25 0.984 B 7.8 0.307 D E 3.3 0.5 e3 0.130 1.78 0.020 22.86 0.070 0.900 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 I 1.27 1.52 0.050 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N1 P Q 4° (min.), 15° (max.) 7.9 8.13 5.71 0.311 0.320 0.
PAGE 11
M54/M74HCT564/574 SO20 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 2.65 0.10 0.104 0.20 a2 MAX. 0.004 0.007 2.45 0.096 b 0.35 0.49 0.013 0.019 b1 0.23 0.32 0.009 0.012 C 0.50 0.020 c1 45° (typ.) D 12.60 13.00 0.496 0.512 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 F 7.40 7.60 0.291 0.299 L 0.50 1.27 0.19 0.050 M S 0.75 0.029 8° (max.
PAGE 12
M54/M74HCT564/574 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.
PAGE 13
M54/M74HCT564/574 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice.