Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - transceivers RS232 1/1 TSSOP 16



      

 ±  



SLLS348M − JUNE 1999 − REVISED MARCH 2004

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

D RS-232 Bus-Pin ESD Protection Exceeds

±15 kV Using Human-Body Model (HBM)

D Meets or Exceeds the Requirements of

TIA/EIA-232-F and ITU v.28 Standards

D Operates With 3-V to 5.5-V V

Supply

D Operates Up To 250 kbit/s

D One Driver and One Receiver

D Low Standby Current...1 µA Typical

D External Capacitors ...4 × 0.1 µF

D Accepts 5-V Logic Input With 3.3-V Supply

D Alternative High-Speed Pin-Compatible

Device (1 Mbit/s)

− SNx5C3221

D Auto-Powerdown Feature Automatically

Disables Drivers for Power Savings

D Applications

− Battery-Powered, Hand-Held, and

Portable Equipment

− PDAs and Palmtop PCs

− Notebooks, Subnotebooks, and Laptops

− Digital Cameras

− Mobile Phones and Wireless Devices

description/ordering information

The MAX3221 consists of one line driver, one line receiver, and a dual charge-pump circuit with ±15-kV ESD

protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of

TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and

the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V

to 5.5-V supply. These devices operate at data signaling rates up to 250 kbit/s and a maximum of 30-V/µs driver

output slew rate.

ORDERING INFORMATION

PACKAGE

†

ORDERABLE

PART NUMBER

TOP-SIDE

MARKING

SSOP (DB)

Tube of 80 MAX3221CDB

MA3221C

−0°C to 70°C

SSOP (DB)

Reel of 2000 MAX3221CDBR

MA3221C

−0°C to 70°C

TSSOP (PW)

Tube of 90 MAX3221CPW

MA3221C

TSSOP (PW)

Reel of 2000 MAX3221CPWR

MA3221C

SSOP (DB)

Tube of 80 MAX3221IDB

MB3221I

−40°C to 85°C

SSOP (DB)

Reel of 2000 MAX3221IDBR

MB3221I

−40°C to 85°C

TSSOP (PW)

Tube of 90 MAX3221IPW

MB3221I

TSSOP (PW)

Reel of 2000 MAX3221IPWR

MB3221I

†

Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are

available at www.ti.com/sc/package.

  !"#$%! & '("")% $& ! *(+,'$%! -$%)

"!-('%& '!!"# %! &*)''$%!& *)" %.) %)"#& ! )/$& &%"(#)%&

&%$-$"- 0$""$%1 "!-('%! *"!')&&2 -!)& !% )')&&$",1 ',(-)

%)&%2 ! $,, *$"$#)%)"&

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

DB OR PW PACKAGE

(TOP VIEW)

C1+

V+

C1−

C2+

C2−

V−

RIN

FORCEOFF

GND

DOUT

FORCEON

DIN

INVALID

ROUT

Summary of content (19 pages)

PAGE 1
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 D RS-232 Bus-Pin ESD Protection Exceeds D D D D D D D D D D DB OR PW PACKAGE (TOP VIEW) ±15 kV Using Human-Body Model (HBM) Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards Operates With 3-V to 5.5-V VCC Supply Operates Up To 250 kbit/s One Driver and One Receiver Low Standby Current . . . 1 µA Typical External Capacitors . . . 4 × 0.
PAGE 2
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 description/ordering information (continued) Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal on the receiver input, the driver output is disabled.
PAGE 3
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 logic diagram (positive logic) DIN FORCEOFF FORCEON ROUT 11 13 DOUT 16 12 10 Auto-powerdown 8 9 1 INVALID RIN EN absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.
PAGE 4
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Note 4 and Figure 6) PARAMETER II Input leakage current TEST CONDITIONS FORCEOFF, FORCEON, EN Auto-powerdown disabled ICC Supply current MIN VCC = 3.
PAGE 5
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 ESD protection TERMINAL NAME NO. DOUT 13 TEST CONDITIONS HBM TYP UNIT ±15 kV RECEIVER SECTION electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Note 4 and Figure 6) PARAMETER VOH VOL TEST CONDITIONS High-level output voltage IOH = −1 mA IOL = 1.
PAGE 6
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 AUTO-POWERDOWN SECTION electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER TEST CONDITIONS MIN VT+(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC VT−(valid) Receiver input threshold for INVALID high-level output voltage
PAGE 7
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 PARAMETER MEASUREMENT INFORMATION 3V Generator (see Note B) Input RS-232 Output 50 Ω RL tTHL CL (see Note A) 3V FORCEOFF TEST CIRCUIT 0V tTLH −3 V −3 V 6V SR(tr) + t THL or t TLH VOH 3V 3V Output VOL VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B.
PAGE 8
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 PARAMETER MEASUREMENT INFORMATION 3V Input 3 V or 0 V FORCEON VCC S1 1.5 V GND 0V tPZH (S1 at GND) tPHZ (S1 at GND) RL 3 V or 0 V 1.5 V VOH Output 50% Output CL (see Note A) EN Generator (see Note B) 50 Ω 0.3 V tPZL (S1 at VCC) tPLZ (S1 at VCC) 0.3 V Output 50% VOL TEST CIRCUIT NOTES: A. B. C. D. VOLTAGE WAVEFORMS CL includes probe and jig capacitance.
PAGE 9
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 PARAMETER MEASUREMENT INFORMATION 2.7 V 2.7 V 0V Receiver Input 0V ROUT Generator (see Note B) 3V −2.7 V −2.7 V 50 Ω −3 V tvalid tinvalid VCC Autopowerdown INVALID CL = 30 pF (see Note A) FORCEOFF FORCEON DIN DOUT 50% VCC INVALID Output 50% VCC 0V ten ≈V+ V+ 0.3 V VCC 0V 0.
PAGE 10
± SLLS348M − JUNE 1999 − REVISED MARCH 2004 APPLICATION INFORMATION EN 1 16 2 VCC C1+ 15 + 3 C1 + + − − V+ Autopowerdown C3† 4 GND − 14 6 C2− 7 − RIN 12 C2 11 V− 10 C4 + DOUT C2+ + − CBYPASS = 0.1 µF C1− 13 5 FORCEOFF 8 9 FORCEON DIN INVALID ROUT 5 kΩ † C3 can be connected to VCC or GND. NOTES: A. Resistor values shown are nominal. B. Nonpolarized ceramic capacitors are acceptable.
PAGE 11
PACKAGE OPTION ADDENDUM www.ti.
PAGE 12
PACKAGE OPTION ADDENDUM www.ti.
PAGE 13
PACKAGE OPTION ADDENDUM www.ti.com 18-Oct-2013 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.
PAGE 14
PACKAGE MATERIALS INFORMATION www.ti.com 5-Jul-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 12.0 16.0 Q1 MAX3221CDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 MAX3221CPWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 MAX3221IDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.
PAGE 15
PACKAGE MATERIALS INFORMATION www.ti.com 5-Jul-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) MAX3221CDBR SSOP DB 16 2000 367.0 367.0 38.0 MAX3221CPWR TSSOP PW 16 2000 367.0 367.0 35.0 MAX3221IDBR SSOP DB 16 2000 367.0 367.0 38.0 MAX3221IPWR TSSOP PW 16 2000 364.0 364.0 27.0 MAX3221IPWRG4 TSSOP PW 16 2000 367.0 367.0 35.
PAGE 16
PAGE 17
PAGE 18
MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters.
PAGE 19
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.