Datasheet

MSP430x23x, MSP430x24x(1), MSP430x2410
MIXED SIGNAL MICROCONTROLLER
SLAS547 -- JUNE 2007
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D Low Supply-Voltage Range: 1.8 V to 3.6 V
D Ultralow Power Consumption:
-- Active Mode: 355 μAat1MHz,2.2V
-- Standby Mode: 0.9 μA
-- Off Mode (RAM Retention): 0.1 μA
D Ultrafast Wake-Up From Standby Mode in
Less Than 1 μs
D 16-Bit RISC Architecture, 62.5-ns
Instruction Cycle Time
D Basic Clock Module Configurations:
-- Internal Frequencies up to 16 MHz
-- Internal Very Low Power LF Oscillator
-- 32-kHz Crystal
-- Internal Frequencies up to 16 MHz With
Four Calibrated Frequencies to ±1%
-- Resonator
-- External Digital Clock Source
-- External Resistor
D 12-Bit A/D Converter With Internal
Reference, Sample-and-Hold, and Autoscan
Feature
D 16-Bit Timer_A With Three
Capture/Compare Registers
D 16-Bit Timer_B With Seven
Capture/Compare-With-Shadow Registers
D Four Universal Serial Communication
Interface (USCI) Modules With:
-- Enhanced UART Supporting
Auto-Baudrate Detection (LIN)
-- IrDA Encoder and Decoder
-- Synchronous SPI
-- I
2
C™
D On-Chip Comparator
D Supply Voltage Supervisor/Monitor With
Programmable Level Detection
D Brownout Detector
D Bootstrap Loader
D Serial Onboard Programming,
No External Programming Voltage Needed,
Programmable Code Protection by Security
Fuse
D Family Members Include:
-- MSP430F233:
8KB+256B Flash Memory, 1KB RAM
-- MSP430F235:
16KB+256B Flash Memory, 2KB RAM
-- MSP430F247, MSP430F2471
†
:
32KB+256B Flash Memory, 4KB RAM
-- MSP430F248, MSP430F2481
†
:
48KB+256B Flash Memory, 4KB RAM
-- MSP430F249, MSP430F2491
†
:
60KB+256B Flash Memory, 2KB RAM
-- MSP430F2410:
56KB+256B Flash Memory, 4KB RAM
D Availablein64-PinQFPand64-PinQFN
(See Available Options)
D For Complete Module Descriptions, See the
MSP430x2xx Family User’s Guide,
Literature Number SLAU144
†
The MSP430F24x1 devices are identical to the MSP430F24x
devices, with the exception that the ADC12 module is not
implemented.
description
The Texas Instruments MSP430 family of ultralow-power mi crocontrollers consists of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low-power
modes, is optimized to achieve extended battery life in portable measurement applications. The device features
a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code
efficiency. The calibrated digitally controlled oscillator (DCO) allows wake-up from low-power modes to active
mode in less than 1 μs.
The MSP430F23x/24x(1)/2410 series are microcontroller configurations with two built-in 16-bit timers, a fast
12-bit A/D converter (not implemented in the MSP430F24x1), a comparator, four universal serial
communication interface (USCI) modules (two in the MSP430F23x), and up to 48 I/O pins. The MSP430F24x1
devices are identical to the MSP430F24x devices, with the exception that the ADC12 module is not
implemented. The MSP430F23x devices are identical to the MSP430F24x devices, with the exception that a
reduced Timer B and less RAM are integrated.
Typical applications include sensor systems, industrial control applications, hand-held meters, etc.
PRODUCT PRE
V
IEW
Copyright © 2007, Texas Instruments Incorporated
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
I
2
C is a trademark of Philips Semiconductors.