User Manual
Table Of Contents
- Getting Started with TI-Nspire™ CX II Handhelds
- About Math Modes
- TI-Nspire™ CX II Handheld Keys
- Preparing the TI-Nspire™ CX II Handheld for Use
- Turning On the TI-Nspire™ CX II Handheld for the First Time
- Adjusting the Brightness of the Backlighting
- Using the TI-Nspire™ Touchpad
- Understanding the Scratchpad
- Using the Home Screen
- The TI-Nspire™ CX II Handheld Screen
- Using Hints
- Using Keyboard Shortcuts
- Using the Scratchpad
- Working with Documents on TI-Nspire™ CX II Handhelds
- Opening a Document
- Creating a New Document
- Saving Documents
- Working with Applications
- Using the Application Menu
- Context Menus
- Working with Problems and Pages
- Adding a Problem to a Document
- Viewing and Reordering Pages in a Document
- Copying, Pasting, and Deleting Problems
- Renaming a Problem
- Adding a Page to a Problem
- Moving Through Pages in a Document
- Managing Documents
- Closing a Document
- Understanding the TI-Nspire™ Tools
- Working with Images
- Working in a TI-Nspire™ CX Premium Teacher Software Classroom
- Configuring Handhelds
- Checking Battery Status
- Recharging the Handheld
- Changing Handheld Settings
- Changing a Preferred Language
- Customizing the Handheld Setup
- Customizing Document Settings
- Customizing Graphs & Geometry Settings
- Viewing Handheld Status
- Replacing TI-Nspire™ Rechargeable Batteries
- Precautions for Rechargeable Batteries
- Connecting Handhelds and Transferring Files
- File Management
- Updating the Handheld Operating System
- General Information
76 Connecting Handhelds and Transferring Files
Shown
on
Message and Description
handheld
OK
This message is displayed if a cable is not attached to the sending handheld’s
link port. Remove and then reinsert the cable and try the document
transmission again.
Click OK to cancel the transmission message.
Note: The sending handheld may not always display this message. Instead, it
may remain BUSY until you cancel the transmission.
Sending
handheld
“Receiver does not have enough storage space for file
transfer.“
OK
This message indicates that the receiving handheld does not have enough
storage to accept the file being transmitted.
The user of the receiving handheld must free space to obtain the new file. To
do this:
• Delete unneeded files.
• Store files on a computer for later retrieval, and then delete them from
the TI-Nspire™ handheld.
Sending
handheld
“<folder>/<filename> transferred as <folder>/<filename(#).“
This message is displayed at the end of a successful transfer when the file had
to be renamed because a file already exists on the receiving handheld with
the original name. The transmitted file is renamed by appending a number to
the end of the name. Rename numbering always begins with (2) and can
increment by one, as needed.
Sending
handheld
“<folder>/<filename> transferred as <folder>/<new filename>.“
This message indicates that a new folder was created on the receiving
handheld to contain the transmitted document.
Receiving
handheld
“<folder>/<filename(x)> received.“
This message indicates that the receiving handheld has a document with the
same name as the document being sent.
Receiving
handheld
“<new folder>/<new filename> received.“
This message indicates that a new folder has been created to contain the
transmitted document.
Receiving
handheld
“Transfer failed. Check cable and try again.“
OK
This message indicates that the cable is not correctly attached to the
receiving handheld’s link port. Remove the cable then reattach it and try the
transmission again.
Click OK to cancel the transmission message.