Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsPMICsPTN78060HAH

FEATURES APPLICATIONS

DESCRIPTION

Inhibit

GND

1%,0.05W

(Required)

PTN78060

(TopView)

STANDARD APPLICATION

SET

4 5

Sense

C *

Ceramic

(Required)

C *

100 Fm

(Required)

*Seethe sectionforcapacitorrecommendations.Theminimuminputcapacitance

is PTN78060W,and PTN78060H.

ApplicationInformation

2.2 Ffor 14.1 F(3x4.7 F)form m m

#R oltage.Seethe sectionforValues.

SET

ApplicationInformationisrequiredtoadjusttheoutputv

PTN78060W , PTN78060H

www.ti.com

................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009

3-A, WIDE-INPUT ADJUSTABLE SWITCHING REGULATOR

• General-Purpose, Industrial Controls,

• 3-A Output Current

HVAC Systems

• Wide-Input Voltage

• Test and Measurement,

(7 V to 36 V) / (15 V to 36 V)

Medical Instrumentation

• Wide-Output Voltage Adjust

• AC/DC Adaptors, Vehicles,

(2.5 V to 12.6 V) / (11.85 V to 22 V)

Marine, and Avionics

• High Efficiency (Up to 96%)

• On/Off Inhibit

• Under-Voltage Lockout

• Output Current Limit

• Overtemperature Shutdown

• Operating Temperature: -40 ° C to 85 ° C

• Surface Mount Package Available

The PTN78060 is a series of high-efficiency, step-down integrated switching regulators (ISR), that represent the

third generation in the evolution of the popular (PT)78ST200, 78ST300, (PT)78HT200, and 78HT300 series of

products. In new designs, the PTN78060 series may also be considered in place of the PT6200, PT6210, and

PT6300 series of single in-line pin (SIP) products. In all cases, the PTN78060 has either similar or improved

electrical performance characteristics. The caseless, double-sided package has excellent thermal characteristics,

and is compatible with TI ' s roadmap for RoHS and lead-free compliance.

Operating from a wide-input voltage range, the PTN78060 provides high-efficiency, step-down voltage

conversion for loads of up to 3 A. The output voltage can be set to any value over a wide adjustment range using

a single external resistor. The PTN78060W may be set to any value within the range, 2.5 V to 12.6 V, and the

PTN78060H from 11.85 V to 22 V. The output voltage of the PTN78060W can be as little as 2 V lower than the

input, allowing operation down to 7 V, with an output voltage of 5 V. The output voltage of the PTN78060H can

be as little as 3 V lower than the input, allowing operation down to 15 V, with an output voltage of 12 V.

The PTN78060 has undervoltage lockout, an integral on/off inhibit, and includes an output current limit and

overtemperature protection. It is well suited to a wide variety of general-purpose applications that operate off

12-V, 24-V, or 28-V DC power.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (26 pages)

PAGE 1
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 3-A, WIDE-INPUT ADJUSTABLE SWITCHING REGULATOR FEATURES APPLICATIONS • • • 1 • • • • • • • • 3-A Output Current Wide-Input Voltage (7 V to 36 V) / (15 V to 36 V) Wide-Output Voltage Adjust (2.5 V to 12.6 V) / (11.
PAGE 2
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
PAGE 3
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 ELECTRICAL CHARACTERISTICS operating at 25°C free-air temperature, VI = 20 V, VO = 5 V, IO = IO (max), CI = 2.
PAGE 4
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com ELECTRICAL CHARACTERISTICS operating at 25°C free-air temperature, VI = 24 V, VO = 12 V, IO = IO (max), CI = 3 × 4.
PAGE 5
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 PIN ASSIGNMENT 1 7 PTN78060 (Top View) 2 6 3 4 5 TERMINAL FUNCTIONS TERMINAL NAME NO. GND 1, 7 I/O DESCRIPTION This is the common ground connection for the VI and VO power connections. It is also the 0-VDC reference for the Inhibit and VO Adjust control inputs.
PAGE 6
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS (7-V INPUT) (1) (2) EFFICIENCY vs OUTPUT CURRENT OUTPUT VOLTAGE RIPPLE vs OUTPUT CURRENT 100 VO = 5 V 80 VO = 3.3 V 70 VO = 2.5 V 60 50 0 0.5 1 1.5 2 2.5 40 VO = 3.3 V 30 VO = 2.
PAGE 7
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 TYPICAL CHARACTERISTICS (15-V INPUT) (1) (2) EFFICIENCY vs OUTPUT CURRENT OUTPUT VOLTAGE RIPPLE vs OUTPUT CURRENT 80 VO = 12 V VO = 9 V 70 VO = 5 V VO = 3.3 V 60 VO = 2.5 V 80 0 0.5 1 1.5 2 2.5 VO = 9 V VO = 5 V VO = 12 V 60 VO = 3.3 V 40 20 3 1 VO = 12 V 0.5 0.
PAGE 8
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS (24-V INPUT) (1) (2) EFFICIENCY vs OUTPUT CURRENT VO = 5 V VO = 3.3 V 60 VO = 2.5 V 50 40 0 0.5 1 1.5 2 2.5 2.5 160 140 VO = 12 V 120 100 80 VO = 3.3 V 60 VO = 5 V VO = 2.5 V 40 VO = 15 V VO = 12 V 2 VO = 5 V 1.5 VO = 3.3 V 1 VO = 2.5 V 0.
PAGE 9
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 TYPICAL CHARACTERISTICS (32-V INPUT) (1) (2) EFFICIENCY vs OUTPUT CURRENT OUTPUT VOLTAGE RIPPLE vs OUTPUT CURRENT 300 VO - Output Voltage Ripple - mVPP VO = 22 V 90 Efficiency - % 80 VO = 15 V 70 VO = 12 V 60 VO = 5 V 50 VO = 3.3 V 0 0.5 1 1.5 2 2.
PAGE 10
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com APPLICATION INFORMATION Adjusting the Output Voltage of the PTN78060 Wide-Output Adjust Power Modules General A resistor must be connected between the VO Adjust control (pin 4) and GND (pin 1) to set the output voltage. The adjustment range is from 2.5 V to 12.6 V for PTN78060W.
PAGE 11
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 5 Sense VI 2 VI PTN78060W VO 6 VO Inhibit GND GND Adjust 3 4 1 7 CI 2.2 mF Ceramic + C O 100 mF RSET 0.05 W 1% Inhibit GND GND (1) A 0.05-W rated resistor may be used. The tolerance should be 1%, with a temperature stability of 100 ppm/°C (or better).
PAGE 12
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com 5 Sense VI 2 VI PTN78060H VO VO 6 Inhibit GND GND Adjust 3 4 1 7 C1 4.7 mF Ceramic C3 4.7 mF Ceramic C2 4.7 mF Ceramic RSET 0.05 W 1% + C4 100 mF GND GND (1) A 0.05-W rated resistor may be used.
PAGE 13
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 CAPACITOR RECOMMENDATIONS for the PTN78060 WIDE-OUTPUT ADJUST POWER MODULES PTN78060W Input Capacitor PTN78060W has a minimum requirement for input capacitance of 2.2 µF of ceramic capacitance. The dielectric may have either an X5R or X7R temperature characteristic.
PAGE 14
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com Tantalum Capacitors Tantalum-type capacitors may be used at the output, and are recommended for applications where the ambient operating temperature can be less than 0°C.
PAGE 15
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 Table 5. Recommended Input/Output Capacitors (PTN78060W) (continued) CAPACITOR CHARACTERISTICS WORKING VOLTAGE (V) VALUE (µF) EQUIVALENT SERIES RESISTANCE (ESR) (Ω) 85° C MAXIMUM RIPPLE CURRENT (IRMS) (mA) 20 100 0.085 1543 20 100 0.200 > 817 Murata X5R Ceramic 6.3 100 0.
PAGE 16
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com Table 6. Recommended Input/Output Capacitors (PTN78060H) CAPACITOR CHARACTERISTICS QUANTITY WORKING VOLTAGE (V) VALUE (µF) EQUIVALENT SERIES RESISTANCE (ESR) (Ω) 85° C MAXIMUM RIPPLE CURRENT (IRMS) (mA) Panasonic FC( Radial) 50 100 0.162 615 10 × 12.5 FK (SMD) 50 150 0.
PAGE 17
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 VI (5 V/div) VO (2 V/div) II (2 A/div) t - Time = 5 ms/div Figure 29. Power-Up Waveforms Undervoltage Lockout The undervoltage lockout (UVLO) circuit prevents the module from attempting to power up until the input voltage is above the UVLO threshold.
PAGE 18
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com To use the output voltage sense feature, simply connect the VO Sense input (pin 5) to VO, close to the device that draws the most supply current. If an external voltage sense is not desired, the VO Sense input may be left open circuit.
PAGE 19
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 VO (2 V/div) II (1 A/div) Q1 VGS (10 V/div) t - Time = 5 ms/div Figure 31. Power-Up Response From Inhibit Control Optional Input/Output Filters Power modules include internal input and output ceramic capacitors in all of their designs.
PAGE 20
PTN78060W, PTN78060H SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009................................................................................................................................................... www.ti.com 5 Rset Sense 2 VI VI C C1 1 µF 50 V Ceramic A Inhibit C2 2.2 µF 50 V Ceramic (Required) VO PTN78060W 3 GND 6 VO B Adjust + 1 7 C3 100 µF (Required) 4 RSET GND C4 2.2 µF Ceramic GND UDG−05086 A. See specifications for required value and type.
PAGE 21
PTN78060W, PTN78060H www.ti.com................................................................................................................................................... SLTS229B – NOVEMBER 2004 – REVISED JUNE 2009 5 Sense L1 1 µH to 5 µH 2 VI D C1 1 µF 50 V Ceramic VI A Vo PTN78060W Inhibit GND GND C2 2.2 µF 50 V Ceramic (Required) 3 1 Adjust 7 L2 1 µH to 5 µH 6 Vo B C + 4 RSET + C3 100 µF (Required) GND C5 C4 2.2 µF Ceramic GND UDG−05087 A.
PAGE 22
PACKAGE OPTION ADDENDUM www.ti.
PAGE 23
PACKAGE OPTION ADDENDUM www.ti.com 26-Aug-2013 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device.
PAGE 24
PAGE 25
PAGE 26
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.